- 您现在的位置：买卖IC网 > PDF目录176103 > ISD5108SYI (WINBOND ELECTRONICS CORP) 480 SEC, SPEECH SYNTHESIZER WITH RCDG, PDSO28 PDF资料下载
参数资料
| 型号： | ISD5108SYI |
| 厂商： | WINBOND ELECTRONICS CORP |
| 元件分类： | 音频合成 |
| 英文描述： | 480 SEC, SPEECH SYNTHESIZER WITH RCDG, PDSO28 |
| 封装： | 0.300 MM INCH, LEAD FREE, PLASTIC, SOIC-28 |
| 文件页数： | 16/89页 |
| 文件大小： | 600K |
| 代理商： | ISD5108SYI |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页
ISD5100 SERIES
Publication Release Date: May 16, 2007
- 23 -
Revision 1.4
To select this mode, the following control bits must be configured in the ISD5100 Series configuration
registers. To set up the transmit path:
1. Select the FTHRU path through the ANA OUT MUX—Bits AOS0, AOS1 and AOS2 control the
state of the ANA OUT MUX. These are the D6, D7 and D8 bits respectively of Configuration
Register 0 (CFG0) and they should all be ZERO to select the FTHRU path.
2. Power up the ANA OUT amplifier—Bit AOPD controls the power up state of ANA OUT. This is
bit D5 of CFG0 and it should be a ZERO to power up the amplifier.
To set up the receive path:
1. Set up the ANA IN amplifier for the correct gain—Bits AIG0 and AIG1 control the gain settings
of this amplifier. These are bits D14 and D15 respectively of CFG0. The input level at this pin
determines the setting of this gain stage. The ANA IN Amplifier Gain Settings table on page
36 will help determine this setting. In this example, we will assume that the peak signal never
goes above 1 volt p-p single ended. That would enable us to use the 9 dB attenuation setting,
or where D14 is ONE and D15 is ZERO.
2. Power up the ANA IN amplifier—Bit AIPD controls the power up state of ANA IN. This is bit
D13 of CFG0 and should be a ZERO to power up the amplifier.
3. Select the ANA IN path through the OUTPUT MUX—Bits OPS0 and OPS1 control the state of
the OUTPUT MUX. These are bits D3 and D4 respectively of CFG0 and they should be set to
the state where D3 is ONE and D4 is ZERO to select the ANA IN path.
4. Power up the Speaker Amplifier—Bits OPA0 and OPA1 control the state of the Speaker and
AUX amplifiers. These are bits D1 and D2 respectively of CFG0. They should be set to the
state where D1 is ONE and D2 is ZERO. This powers up the Speaker Amplifier and
configures it for its higher gain setting for use with a piezo speaker element and also powers
down the AUX output stage.
The status of the rest of the functions in the ISD5100 Series chip must be defined before the con-
figuration registers settings are updated:
1.
Power down the Volume Control Element—Bit VLPD controls the power up state of the
Volume Control. This is bit D0 of CFG0 and it should be set to a ONE to power down this
stage.
2.
Power down the AUX IN amplifier—Bit AXPD controls the power up state of the AUX IN input
amplifier. This is bit D10 of CFG0 and it should be set to a ONE to power down this stage.
3.
Power down the SUM1 and SUM2 Mixer amplifiers—Bits S1M0 and S1M1 control the SUM1
mixer and bits S2M0 and S2M1 control the SUM2 mixer. These are bits D7 and D8 in CFG1
and bits D5 and D6 in CFG1 respectively. All 4 bits should be set to a ONE to power down
these two amplifiers.
4.
Power down the FILTER stage—Bit FLPD controls the power up state of the FILTER stage in
the device. This is bit D1 in CFG1 and should be set to a ONE to power down the stage.
5.
Power down the AGC amplifier—Bit AGPD controls the power up state of the AGC amplifier.
This is bit D0 in CFG1 and should be set to a ONE to power down this stage.
相关PDF资料 |
PDF描述 |
|---|---|
| ISD5108SY | 480 SEC, SPEECH SYNTHESIZER WITH RCDG, PDSO28 |
| ISD5108X | 480 SEC, SPEECH SYNTHESIZER WITH RCDG, UUC27 |
| ISD5116EYI | 960 SEC, SPEECH SYNTHESIZER WITH RCDG, PDSO28 |
| ISD5116EY | 960 SEC, SPEECH SYNTHESIZER WITH RCDG, PDSO28 |
| ISD5116SYI | 960 SEC, SPEECH SYNTHESIZER WITH RCDG, PDSO28 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISD5108SYIR | 功能描述:IC VOICE REC/PLAY 4-8MN 28-SOIC RoHS:是 类别:集成电路 (IC) >> 接口 - 语音录制和重放 系列:ISD5100 标准包装:14 系列:- 接口:串行 滤波器通频带:1.7kHz 持续时间:8 ~ 32 秒 安装类型:通孔 封装/外壳:28-DIP（0.300"，7.62mm） 供应商设备封装:28-PDIP 其它名称:90-21300+000 |
| ISD5108SYR | 功能描述:IC VOICE REC/PLAY 4-8MN 28-SOIC RoHS:是 类别:集成电路 (IC) >> 接口 - 语音录制和重放 系列:ISD5100 标准包装:14 系列:- 接口:串行 滤波器通频带:1.7kHz 持续时间:8 ~ 32 秒 安装类型:通孔 封装/外壳:28-DIP（0.300"，7.62mm） 供应商设备封装:28-PDIP 其它名称:90-21300+000 |
| ISD5116 | 制造商:WINBOND 制造商全称:Winbond 功能描述:Single-Chip Voice Record/Playback Device Up to 16-Minute Duration with Digital Storage Capability |
| ISD5116E | 功能描述:IC VOICE REC/PLAY 8-16MN 28-TSOP RoHS:否 类别:集成电路 (IC) >> 接口 - 语音录制和重放 系列:ISD5100 标准包装:14 系列:- 接口:串行 滤波器通频带:1.7kHz 持续时间:8 ~ 32 秒 安装类型:通孔 封装/外壳:28-DIP（0.300"，7.62mm） 供应商设备封装:28-PDIP 其它名称:90-21300+000 |
| ISD5116ED | 功能描述:IC VOICE REC/PL 8-16MN EX 28TSOP RoHS:否 类别:集成电路 (IC) >> 接口 - 语音录制和重放 系列:ISD5100 标准包装:14 系列:- 接口:串行 滤波器通频带:1.7kHz 持续时间:8 ~ 32 秒 安装类型:通孔 封装/外壳:28-DIP（0.300"，7.62mm） 供应商设备封装:28-PDIP 其它名称:90-21300+000 |
发布紧急采购，3分钟左右您将得到回复。