参数资料
| 型号： | ISL12026IBZ-T7A |
| 厂商： | Intersil |
| 文件页数： | 9/24页 |
| 文件大小： | 0K |
| 描述： | IC RTC/CALENDAR EEPROM 8SOIC |
| 标准包装： | 250 |
| 类型： | 时钟/日历 |
| 特点： | 警报器，闰年 |
| 时间格式： | HH:MM:SS（12/24 小时） |
| 数据格式： | YY-MM-DD-dd |
| 接口： | I²C，2 线串口 |
| 电源电压： | 2.7 V ~ 5.5 V |
| 电压 - 电源，电池： | 1.8 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOIC |
| 包装： | 带卷 (TR) |
17
FN8231.9
November 30, 2010
individual register writes are not allowed. (Note: Prior to
writing to the CCR, the master must write a 02h, then 06h to
the status register in two preceding operations to enable the
write operation. See “Writing to the Clock/Control Registers”
After the receipt of each byte, the ISL12026 responds with
an acknowledge, and the address is internally incremented
by one. The address pointer remains at the last address byte
written. When the counter reaches the end of the page, it
“rolls over” and goes back to the first address on the same
page. This means that the master can write 16 bytes to a
memory array page or 8 bytes to a CCR section starting at
any location on that page. For example, if the master begins
writing at location 10 of the memory and loads 15 bytes, then
the first 6 bytes are written to addresses 10 through 15, and
the last 6 bytes are written to columns 0 through 5.
Afterwards, the address counter would point to location 6 on
the page that was just written. If the master supplies more
than the maximum bytes in a page, then the previously
loaded data is over-written by the new data, one byte at a
time. Refer to Figure 18. The master terminates the Data
Byte loading by issuing a stop condition, which causes the
ISL12026 to begin the non-volatile write cycle. As with the
byte write operation, all inputs are disabled until completion
of the internal write cycle. Refer to Figure 17 for the address,
acknowledge, and data transfer sequence.
Stops and Write Modes
Stop conditions that terminate write operations must be sent
by the master after sending at least 1 full data byte and it’s
associated ACK signal. If a stop is issued in the middle of a
data byte, or before 1 full data byte + ACK is sent, then the
ISL12026 resets itself without performing the write. The
contents of the array are not affected.
WORD
ADDRESS 0
S
T
A
R
T
S
T
O
P
SLAVE
ADDRESS
WORD
ADDRESS 1
DATA
(n)
A
C
K
A
C
K
A
C
K
SDA BUS
SIGNALS FROM
THE SLAVE
SIGNALS FROM
THE MASTER
0
DATA
(1)
A
C
K
1
≤ N ≤ 16 FOR EEPROM ARRAY
1
≤ N ≤ 8 FOR CCR
1
000 0 0 0 0
FIGURE 17. PAGE WRITE SEQUENCE
ADDRESS
10
6 BYTES
15
6 BYTES
ADDRESS = 5
ADDRESS POINTER ENDS
FIGURE 18. WRITING 12 BYTES TO A 16-BYTE MEMORY PAGE STARTING AT ADDRESS 10
AT ADDR = 5
ISL12026, ISL12026A
相关PDF资料 |
PDF描述 |
|---|---|
| ISL12027IV27AZ | IC RTC/CALENDAR EEPROM 8-TSSOP |
| ISL12028IVZ | IC RTC/CALENDAR EEPROM 14-TSSOP |
| ISL12029IVZ | IC RTC/CALENDAR EEPROM 14-TSSOP |
| ISL12030IBZ | IC RTC/CALENDAR EEPROM 8-SOIC |
| ISL12032IVZ | IC RTC LP BATT BACK SRAM 14TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL12026IVZ | 功能描述:实时时钟 REAL TIME CLK/CLNDR W/EEPROM IN 8LD RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 总线接口:I2C 日期格式:DW:DM:M:Y 时间格式:HH:MM:SS RTC 存储容量:64 B 电源电压-最大:5.5 V 电源电压-最小:1.8 V 最大工作温度:+ 85 C 最小工作温度: 安装风格:Through Hole 封装 / 箱体:PDIP-8 封装:Tube |
| ISL12026IVZ-T | 功能描述:实时时钟 REAL TIME CLK/CLNDR W/EEPROM IN 8LD RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 总线接口:I2C 日期格式:DW:DM:M:Y 时间格式:HH:MM:SS RTC 存储容量:64 B 电源电压-最大:5.5 V 电源电压-最小:1.8 V 最大工作温度:+ 85 C 最小工作温度: 安装风格:Through Hole 封装 / 箱体:PDIP-8 封装:Tube |
| ISL12027 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Real Time Clock/Calendar with EEPROM |
| ISL12027_10 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Real Time Clock/Calendar with EEPROM |
| ISL12027A | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Real Time Clock/Calendar with EEPROM |
发布紧急采购，3分钟左右您将得到回复。