参数资料
型号: ISL12032IVZ-T
厂商: Intersil
文件页数: 15/26页
文件大小: 0K
描述: IC RTC LP BATT BACK SRAM 14TSSOP
产品培训模块: Solutions for Industrial Control Applications
标准包装: 1
类型: 时间事件记录器
特点: 警报器,SRAM,涓流充电器
存储容量: 128B
时间格式: HH:MM:SS:hh(12/24 小时)
数据格式: YY-MM-DD-dd
接口: I²C,2 线串口
电源电压: 2.7 V ~ 5.5 V
电压 - 电源,电池: 1.8 V ~ 5.5 V
工作温度: -40°C ~ 85°C
安装类型: 表面贴装
封装/外壳: 14-TSSOP(0.173",4.40mm 宽)
供应商设备封装: 14-TSSOP
包装: 标准包装
产品目录页面: 1246 (CN2011-ZH PDF)
其它名称: ISL12032IVZ-TDKR
22
FN6618.3
May 5, 2011
Protocol Conventions
Data states on the SDA line can change only during SCL
LOW periods. SDA state changes during SCL HIGH are
reserved for indicating START and STOP conditions (see
Figure 6). On power-up of the ISL12032, the SDA pin is in
the input mode.
All I2C interface operations must begin with a START
condition, which is a HIGH to LOW transition of SDA while
SCL is HIGH. The ISL12032 continuously monitors the SDA
and SCL lines for the START condition and does not
respond to any command until this condition is met (see
Figure 6). A START condition is ignored during the power-up
sequence.
All I2C interface operations must be terminated by a STOP
condition, which is a LOW to HIGH transition of SDA while
SCL is HIGH (see Figure 6). A STOP condition at the end of
a read operation or at the end of a write operation to memory
only places the device in its standby mode.
An acknowledge (ACK) is a software convention used to
indicate a successful data transfer. The transmitting device,
either master or slave, releases the SDA bus after
transmitting eight bits. During the ninth clock cycle, the
receiver pulls the SDA line LOW to acknowledge the
reception of the eight bits of data (see Figure 7).
The ISL12032 responds with an ACK after recognition of a
START condition followed by a valid Identification Byte, and
once again after successful receipt of an Address Byte. The
ISL12032 also responds with an ACK after receiving a Data
Byte of a write operation. The master must respond with an
ACK after receiving a Data Byte of a read operation.
FIGURE 6. VALID DATA CHANGES, START AND STOP CONDITIONS
FIGURE 7. ACKNOWLEDGE RESPONSE FROM RECEIVER
FIGURE 8. BYTE WRITE SEQUENCE (SLAVE ADDRESS FOR CSR SHOWN)
SDA
SCL
START
DATA
STOP
STABLE
CHANGE
DATA
STABLE
SDA OUTPUT FROM
TRANSMITTER
SDA OUTPUT FROM
RECEIVER
8
1
9
START
ACK
SCL FROM
MASTER
HIGH IMPEDANCE
S
T
A
R
T
S
T
O
P
IDENTIFICATION
BYTE
DATA
BYTE
A
C
K
SIGNALS FROM
THE MASTER
SIGNALS FROM
THE ISL12032
A
C
K
10
0
11
A
C
K
WRITE
SIGNAL AT SDA
00 00
11 1
ADDRESS
BYTE
ISL12032
相关PDF资料
PDF描述
VE-J1N-MZ CONVERTER MOD DC/DC 18.5V 25W
VI-J1N-MZ CONVERTER MOD DC/DC 18.5V 25W
VE-J1P-MZ CONVERTER MOD DC/DC 13.8V 25W
ISL1209IU10Z-TK IC RTC LP SRAM EEPROM 10-MSOP
VI-J3Z-EY-F4 CONVERTER MOD DC/DC 2V 20W
相关代理商/技术参数
参数描述
ISL12057 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Low Cost and Low Power I2C RTC Real Time Clock/Calendar
ISL12057IBZ 功能描述:实时时钟 REAL TIME CLK W/ ALARM DS1337 COMP RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 总线接口:I2C 日期格式:DW:DM:M:Y 时间格式:HH:MM:SS RTC 存储容量:64 B 电源电压-最大:5.5 V 电源电压-最小:1.8 V 最大工作温度:+ 85 C 最小工作温度: 安装风格:Through Hole 封装 / 箱体:PDIP-8 封装:Tube
ISL12057IBZ-T 功能描述:实时时钟 REAL TIME CLK W/ ALARM DS1337 COMP RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 总线接口:I2C 日期格式:DW:DM:M:Y 时间格式:HH:MM:SS RTC 存储容量:64 B 电源电压-最大:5.5 V 电源电压-最小:1.8 V 最大工作温度:+ 85 C 最小工作温度: 安装风格:Through Hole 封装 / 箱体:PDIP-8 封装:Tube
ISL12057IRUZ-T 功能描述:实时时钟 REAL TIME CLK W/ ALARM DS1337 COMP RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 总线接口:I2C 日期格式:DW:DM:M:Y 时间格式:HH:MM:SS RTC 存储容量:64 B 电源电压-最大:5.5 V 电源电压-最小:1.8 V 最大工作温度:+ 85 C 最小工作温度: 安装风格:Through Hole 封装 / 箱体:PDIP-8 封装:Tube
ISL12057IUZ 功能描述:实时时钟 REAL TIME CLK W/ ALARM DS1337 COMP RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 总线接口:I2C 日期格式:DW:DM:M:Y 时间格式:HH:MM:SS RTC 存储容量:64 B 电源电压-最大:5.5 V 电源电压-最小:1.8 V 最大工作温度:+ 85 C 最小工作温度: 安装风格:Through Hole 封装 / 箱体:PDIP-8 封装:Tube