- 您现在的位置：买卖IC网 > PDF目录383128 > ISL1218 (Intersil Corporation) Low Power RTC with Battery Backed SRAM(具有电池供电SRAM的低功率RTC) PDF资料下载
参数资料
| 型号： | ISL1218 |
| 厂商： | Intersil Corporation |
| 英文描述： | Low Power RTC with Battery Backed SRAM(具有电池供电SRAM的低功率RTC) |
| 中文描述： | 低功耗RTC与电池供电的SRAM（具有电池供电的SRAM的低功率实时时钟） |
| 文件页数： | 12/21页 |
| 文件大小： | 351K |
| 代理商： | ISL1218 |
12
FN6313.0
June 22, 2006
NOTE: Writing to register 08h has restrictions. If V
BAT
>V
DD
, then no
byte writes to register 08h are allowed, only page writes beginning
with register 07h. If V
DD
>V
BAT
, then a byte write to register 08h IS
allowed, as well as page writes.
FREQUENCY OUT CONTROL BITS (FO <3:0>)
These bits enable/disable the frequency output function and
select the output frequency at the IRQ/F
OUT
pin. See
Table 4 for frequency selection. When the frequency mode is
enabled, it will override the alarm mode at the IRQ/F
OUT
pin.
FREQUENCY OUTPUT AND INTERRUPT BIT (FOBATB)
This bit enables/disables the F
OUT
/IRQ pin during battery
backup mode (i.e. V
BAT
power source active). When the
FOBATB is set to “1” the F
OUT
/IRQ pin is disabled during
battery backup mode. This means that both the frequency
output and alarm output functions are disabled. When the
FOBATB is cleared to “0”, the F
OUT
/IRQ pin is enabled
during battery backup mode.
LOW POWER MODE BIT (LPMODE)
This bit enables/disables low power mode. With
LPMODE = “0”, the device will be in normal mode and the
V
BAT
supply will be used when V
DD
< V
BAT
- V
BATHYS
and
V
DD
< V
TRIP
. With LPMODE = “1”, the device will be in low
power mode and the V
BAT
supply will be used when
V
DD
< V
BAT
- V
BATHYS
. There is a supply current saving of
about 600nA when using LPMODE = “1” with V
DD
= 5V.
(See Typical Performance Curves: I
DD
vs V
CC
with
LPMODE ON and OFF.)
It should be noted that any writes to the LPMODE bit that
may put the device into Low Power Mode should be avoided
if V
DD
<V
BAT
, as the device will no longer communicate over
the I
2
C interface (until V
DD
rises above V
BAT
).
ALARM ENABLE BIT (ALME)
This bit enables/disables the alarm function. When the ALME
bit is set to “1”, the alarm function is enabled. When the ALME
is cleared to “0”, the alarm function is disabled. The alarm
function can operate in either a single event alarm or a periodic
interrupt alarm (see IM bit).
NOTE: When the frequency output mode is enabled, the alarm function
is disabled.
INTERRUPT/ALARM MODE BIT (IM)
This bit enables/disables the interrupt mode of the alarm
function. When the IM bit is set to “1”, the alarm will operate
in the interrupt mode, where an active low pulse width of
250ms will appear at the IRQ/F
OUT
pin when the RTC is
triggered by the alarm as defined by the alarm registers (0Ch
to 11h). When the IM bit is cleared to “0”, the alarm will
operate in standard mode, where the IRQ/F
OUT
pin will be
tied low until the ALM status bit is cleared to “0”.
Analog Trimming Register
ANALOG TRIMMING REGISTER (ATR<5:0>)
Six analog trimming bits,
ATR0
to
ATR5
, are provided in
order to adjust the on-chip load capacitance value for
frequency compensation of the RTC. Each bit has a different
weight for capacitance adjustment. For example, using a
Citizen CFS-206 crystal with different ATR bit combinations
provides an estimated ppm adjustment range from -34 to
+80ppm to the nominal frequency compensation. The
combination of analog and digital trimming can give up to -94
to +140ppm of total adjustment.
TABLE 4. FREQUENCY SELECTION OF F
OUT
PIN
FREQUENCY,
F
OUT
UNITS
FO3
FO2
FO1
FO0
0
Hz
0
0
0
0
32768
Hz
0
0
0
1
4096
Hz
0
0
1
0
1024
Hz
0
0
1
1
64
Hz
0
1
0
0
32
Hz
0
1
0
1
16
Hz
0
1
1
0
8
Hz
0
1
1
1
4
Hz
1
0
0
0
2
Hz
1
0
0
1
1
Hz
1
0
1
0
1/2
Hz
1
0
1
1
1/4
Hz
1
1
0
0
1/8
Hz
1
1
0
1
1/16
Hz
1
1
1
0
1/32
Hz
1
1
1
1
IM BIT
INTERRUPT/ALARM FREQUENCY
0
Single Time Event Set By Alarm
1
Repetitive/Recurring Time Event Set By Alarm
FIGURE 11. DIAGRAM OF ATR
C
X1
X1
X2
CRYSTAL
OSCILLATOR
C
X2
ISL1218
相关PDF资料 |
PDF描述 |
|---|---|
| ISL1219 | Low Power RTC with Battery Backed SRAM and Event Detection(具有电池供电的SRAM和事件检测功能的低功率RTC) |
| ISL1220 | Low Power RTC with 8 Bytes of Battery Backed SRAM and Separate FOUT(具有电池供电的8位SRAM和独立输出的低功率RTC) |
| ISL1221 | Low Power RTC with Battery Backed SRAM and Event Detection(具有电池供电的SRAM和事件检测功能的低功率RTC) |
| ISL21009 | High Voltage Input Precision, Low Noise FGA Voltage References(高电压输入精度，低噪声FGA电压基准) |
| ISL21400 | Programmable Temperature Slope Voltage Reference(可编程温度斜率电压基准) |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL1218IBZ | 功能描述:实时时钟 REAL TIME CLKRTC IN 8LD RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 总线接口:I2C 日期格式:DW:DM:M:Y 时间格式:HH:MM:SS RTC 存储容量:64 B 电源电压-最大:5.5 V 电源电压-最小:1.8 V 最大工作温度:+ 85 C 最小工作温度: 安装风格:Through Hole 封装 / 箱体:PDIP-8 封装:Tube |
| ISL1218IBZ-T | 功能描述:实时时钟 REAL TIME CLKRTC IN 8LD RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 总线接口:I2C 日期格式:DW:DM:M:Y 时间格式:HH:MM:SS RTC 存储容量:64 B 电源电压-最大:5.5 V 电源电压-最小:1.8 V 最大工作温度:+ 85 C 最小工作温度: 安装风格:Through Hole 封装 / 箱体:PDIP-8 封装:Tube |
| ISL1218IUZ | 功能描述:实时时钟 REAL TIME CLKRTC IN RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 总线接口:I2C 日期格式:DW:DM:M:Y 时间格式:HH:MM:SS RTC 存储容量:64 B 电源电压-最大:5.5 V 电源电压-最小:1.8 V 最大工作温度:+ 85 C 最小工作温度: 安装风格:Through Hole 封装 / 箱体:PDIP-8 封装:Tube |
| ISL1218IUZ-T | 功能描述:实时时钟 REAL TIME CLKRTC IN RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 总线接口:I2C 日期格式:DW:DM:M:Y 时间格式:HH:MM:SS RTC 存储容量:64 B 电源电压-最大:5.5 V 电源电压-最小:1.8 V 最大工作温度:+ 85 C 最小工作温度: 安装风格:Through Hole 封装 / 箱体:PDIP-8 封装:Tube |
| ISL1219 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Low Power RTC with Battery Backed SRAM and Event Detection |
发布紧急采购，3分钟左右您将得到回复。