- 您现在的位置：买卖IC网 > PDF目录383128 > ISL22329 (Intersil Corporation) Low Noise, Low Power, I2C Bus, 128 Taps, Wiper Only(低噪声,低功率，I2C总线, 128抽头电位器) PDF资料下载
参数资料
| 型号： | ISL22329 |
| 厂商： | Intersil Corporation |
| 英文描述： | Low Noise, Low Power, I2C Bus, 128 Taps, Wiper Only(低噪声,低功率，I2C总线, 128抽头电位器) |
| 中文描述： | 低噪声，低功耗，I2C总线，128抽头，雨刷，只有（低噪声，低功率和I2C总线，128抽头电位器） |
| 文件页数： | 11/12页 |
| 文件大小： | 333K |
| 代理商： | ISL22329 |
11
FN6330.1
September 26, 2006
Write Operation
A Write operation requires a START condition, followed by a
valid Identification Byte, a valid Address Byte, a Data Byte,
and a STOP condition. After each of the three bytes, the
ISL22329 responds with an ACK. At this time, the device
enters its standby state (See Figure 14). Device can receive
more than one byte of data by auto incrementing the
address after each received byte. Note after reaching the
address 08h, the internal pointer “rolls over” to address 00h.
Non-volatile write cycle starts after STOP condition is
determined and it requires up to 20 ms delay for the next
non-volatile write. Thus, non-volatile registers must be
written individually.
Read Operation
A Read operation consist of a three byte instruction followed
by one or more Data Bytes (See Figure 15). The master
initiates the operation issuing the following sequence: a
START, the Identification byte with the R/W bit set to “0”, an
Address Byte, a second START, and a second Identification
byte with the R/W bit set to “1”. After each of the three bytes,
the ISL22329 responds with an ACK. Then the ISL22329
transmits Data Bytes as long as the master responds with an
ACK during the SCL cycle following the eighth bit of each
byte. The Data Bytes are from the registers indicated by an
internal pointer. This pointer initial value is determined by the
Address Byte in the Read operation instruction, and
increments by one during transmission of each Data Byte.
After reaching the memory location 08h, the pointer “rolls
over” to 00h, and the device continues to output data for
each ACK received.The master terminates the read
operation (issuing a ACK and STOP condition) following the
last bit of the last Data Byte (See Figure 15).
The Data Bytes are from the registers indicated by an
internal pointer. This pointer initial value is determined by the
Address Byte in the Read operation instruction, and
increments by one during transmission of each Data Byte.
After reaching the memory location 08h, the pointer “rolls
over” to 00h, and the device continues to output data for
each ACK received.
In order to read back the non-volatile IVR, it is recommended
that the application reads the ACR first to verify the WIP bit
is 0. If the WIP bit (ACR[5]) is not 0, the host should repeat
its reading sequence again.
S
T
A
R
T
S
T
O
P
IDENTIFICATION
BYTE
ADDRESS
BYTE
DATA
BYTE
A
C
K
SIGNALS FROM
THE MASTER
SIGNALS FROM
THE SLAVE
A
C
K
1
0
1
0
0
A
C
K
WRITE
SIGNAL AT SDA
0 0 0 0
A0
A1
A2
FIGURE 14. BYTE WRITE SEQUENCE
SIGNALS
FROM THE
MASTER
SIGNALS FROM
THE SLAVE
SIGNAL AT SDA
S
T
A
R
T
IDENTIFICATION
BYTE WITH
R/W=0
ADDRESS
BYTE
A
C
K
A
C
K
1
0
1
0
0
S
T
O
P
A
C
K
1
1
1
0
0
IDENTIFICATION
BYTE WITH
R/W = 1
A
C
K
S
T
A
R
T
LAST READ
DATA BYTE
FIRST READ
DATA BYTE
A
C
K
0
0 0 0
A0
A1
A2
A0
A1
A2
FIGURE 15. READ SEQUENCE
A
C
K
ISL22329
相关PDF资料 |
PDF描述 |
|---|---|
| ISL22346 | Low Noise, Low Power I2C Bus, 128 Taps(低噪声,低功率，I2C总线, 128抽头电位器) |
| ISL22349 | Low Noise, Low Power, I2C Bus, 128 Taps, Wiper Only(低噪声,低功率，I2C总线, 128抽头电位器) |
| ISL23710UIU10Z | Terminal Voltage +-3V or +-5V, 128 Taps Up/Down Interface |
| ISL23710WIU10Z | Terminal Voltage +-3V or +-5V, 128 Taps Up/Down Interface |
| ISL23710 | Terminal Voltage +-3V or +-5V, 128 Taps Up/Down Interface |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL22329UFU10Z | 功能描述:IC POT DGTL 128TP LN LP 10-MSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数字电位器 系列:XDCP™ 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 接片:32 电阻（欧姆）:50k 电路数:1 温度系数:标准值 50 ppm/°C 存储器类型:易失 接口:3 线串行（芯片选择，递增，增/减） 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 细型，TSOT-23-6 供应商设备封装:TSOT-23-6 包装:带卷 (TR) |
| ISL22329UFU10Z-TK | 功能描述:IC POT DGTL 128TP LN LP 10-MSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数字电位器 系列:XDCP™ 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 接片:32 电阻（欧姆）:50k 电路数:1 温度系数:标准值 50 ppm/°C 存储器类型:易失 接口:3 线串行（芯片选择，递增，增/减） 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 细型，TSOT-23-6 供应商设备封装:TSOT-23-6 包装:带卷 (TR) |
| ISL22329WFU10Z | 功能描述:IC POT DGTL 128TP LN LP 10-MSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数字电位器 系列:XDCP™ 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 接片:32 电阻（欧姆）:50k 电路数:1 温度系数:标准值 50 ppm/°C 存储器类型:易失 接口:3 线串行（芯片选择，递增，增/减） 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 细型，TSOT-23-6 供应商设备封装:TSOT-23-6 包装:带卷 (TR) |
| ISL22329WFU10Z-TK | 功能描述:IC POT DGTL 128TP LN LP 10-MSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数字电位器 系列:XDCP™ 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 接片:32 电阻（欧姆）:50k 电路数:1 温度系数:标准值 50 ppm/°C 存储器类型:易失 接口:3 线串行（芯片选择，递增，增/减） 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 细型，TSOT-23-6 供应商设备封装:TSOT-23-6 包装:带卷 (TR) |
| ISL22343 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Quad Digitally Controlled Potentiometer XDCP |
发布紧急采购，3分钟左右您将得到回复。