参数资料
| 型号： | ISL22343UFR20Z |
| 厂商： | Intersil |
| 文件页数： | 7/18页 |
| 文件大小： | 0K |
| 描述： | IC POT DGTL 256TP LN LP 20-QFN |
| 标准包装： | 600 |
| 系列： | XDCP™ |
| 接片： | 256 |
| 电阻（欧姆）： | 50k |
| 电路数： | 4 |
| 温度系数： | 标准值 ±45 ppm/°C |
| 存储器类型： | 非易失 |
| 接口： | I²C（设备位址） |
| 电源电压： | 2.25 V ~ 5.5 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-VQFN 裸露焊盘 |
| 供应商设备封装： | 20-QFN 裸露焊盘（5x5） |
| 包装： | 管件 |
15
FN6423.1
March 13, 2008
Write Operation
A Write operation requires a START condition, followed by a
valid Identification Byte, a valid Address Byte, a Data Byte,
and a STOP condition. After each of the three bytes, the
ISL22343 responds with an ACK. At this time, the device
enters its standby state (see Figure 18).
The non-volatile write cycle starts after STOP condition is
determined and it requires up to 20ms delay for the next
non-volatile write. Thus, non-volatile registers must be
written individually.
Read Operation
A Read operation consist of a three byte instruction followed
by one or more Data Bytes (see Figure 19). The master
initiates the operation issuing the following sequence: a
START, the Identification byte with the R/W bit set to “0”, an
Address Byte, a second START, and a second Identification
byte with the R/W bit set to “1”. After each of the three bytes,
the ISL22343 responds with an ACK. Then the ISL22343
transmits Data Bytes as long as the master responds with an
ACK during the SCL cycle following the eighth bit of each
byte. The Data Bytes are from the registers indicated by an
internal pointer. This pointers initial value is determined by
the Address Byte in the Read operation instruction, and
increments by one during transmission of each Data Byte.
After reaching the memory location 0Fh, the pointer “rolls
over” to 00h, and the device continues to output data for
each ACK received.The master terminates the read
operation issuing a NACK (ACK) and a STOP condition
following the last bit of the last Data Byte (See Figure 19).
Applications Information
When stepping up through each tap in voltage divider mode,
some tap transition points can result in noticeable voltage
transients (or overshoot/undershoot) resulting from the
sudden transition from a very low impedance “make” to a
much higher impedance “break within an extremely short
period of time (<50ns). Two such code transitions are EFh to
F0h, and 0Fh to 10h. Note that all switching transients will
settle well within the settling time as stated on the datasheet.
A small capacitor can be added externally to reduce the
amplitude of these voltage transients, but that will also
reduce the useful bandwidth of the circuit, thus this may not
be a good solution for some applications. It may be a good
idea, in that case, to use fast amplifiers in a signal chain for
fast recovery.
Application Example
Figure 20 shows an example of using ISL22343 for gain
setting and offset correction in a high side current
measurement application. DCP0 applies a programmable
offset voltage of ±25mV to the FB+ pin of the Instrumentation
Amplifier ISL28272 to adjust output offset to zero voltages.
DCP1 programs the gain of the ISL28272 from 90 to 110
with 5V output for 10A current through current sense
resistor. DCP2 and DCP3 are used for another channel of
dual ISL28272 correspondently (not shown in Figure 20).
More application examples can be found at
http://www.intersil.com/data/an/AN1145.pdf
SIGNALS
FROM THE
MASTER
SIGNALS FROM
THE SLAVE
SIGNAL AT SDA
S
T
A
R
T
IDENTIFICATION
BYTE WITH
R/W = 0
ADDRESS
BYTE
A
C
K
A
C
K
10
1
00
S
T
O
P
A
C
K
1
IDENTIFICATION
BYTE WITH
R/W = 1
A
C
K
S
T
A
R
T
LAST READ
DATA BYTE
FIRST READ
DATA BYTE
A
C
K
0
00 0
A0
A1
A0
A1
FIGURE 19. READ SEQUENCE
A
C
K
A2
10 1 0
ISL22343
相关PDF资料 |
PDF描述 |
|---|---|
| X9420WV14IZT1 | IC DGTL POT 10K 1CH 14TSSOP |
| X9429YV14IZT1 | IC XDCP SGL 64-TAP 2.5K 14-TSSOP |
| X9429WV14IZT1 | IC XDCP SGL 64-TAP 10K 14-TSSOP |
| MS3452W28-20SW | CONN RCPT 14POS BOX MNT W/SCKT |
| MS3452W28-20S | CONN RCPT 14POS BOX MNT W/SCKT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL22343UFR20Z-TK | 功能描述:数字电位计 IC 265 TAP FL RNG IND QD I2C DCP 5X5 RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
| ISL22343UFV20Z | 功能描述:数字电位计 IC 256 TAP FL RNG IND QD I2C DCP 20LD RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
| ISL22343UFV20Z-TK | 功能描述:数字电位计 IC 259 TAP FL RNG IND QD I2C DCP 20LD RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
| ISL22343WFR20Z | 功能描述:数字电位计 IC 263 TAP FL RNG IND QD I2C DCP 5X5 RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
| ISL22343WFR20Z-TK | 功能描述:数字电位计 IC 266 TAP FL RNG IND QD I2C DCP 5X5 RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。