参数资料
| 型号： | ISL22446WFRT20Z |
| 厂商： | Intersil |
| 文件页数： | 2/15页 |
| 文件大小： | 0K |
| 描述： | IC POT DGTL 128TP LN LP 20-TQFN |
| 产品培训模块： | Solutions for Industrial Control Applications |
| 标准包装： | 75 |
| 系列： | XDCP™ |
| 接片： | 128 |
| 电阻（欧姆）： | 10k |
| 电路数： | 4 |
| 温度系数： | 标准值 ±50 ppm/°C |
| 存储器类型： | 非易失 |
| 接口： | 4 线 SPI（芯片选择） |
| 电源电压： | 2.7 V ~ 5.5 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-WFQFN 裸露焊盘 |
| 供应商设备封装： | 20-TQFN（4x4） |
| 包装： | 管件 |
10
FN6181.2
September 9, 2009
Pin Description
Potentiometers Pins
RHI AND RLI (i = 0, 1, 2, 3)
The high (RHi) and low (RLi) terminals of the ISL22446 are
equivalent to the fixed terminals of a mechanical
potentiometer. RHi and RLi are referenced to the relative
position of the wiper and not the voltage potential on the
terminals. With WRi set to 127 decimal, the wiper will be
closest to RHi, and with the WRi set to 0, the wiper is closest
to RLi.
RWI (i = 0, 1, 2, 3)
RWi is the wiper terminal and is equivalent to the movable
terminal of a mechanical potentiometer. The position of the
wiper within the array is determined by the WRi register.
SHDN
The SHDN pin forces the resistor to end-to-end open circuit
condition on RHi and shorts RWi to RLi. When SHDN is
returned to logic high, the previous latch settings put RWi at
the same resistance setting prior to shutdown. This pin is
logically ANDed with SHDN bit in ACR register. SPI interface
is still available in shutdown mode and all registers are
accessible. This pin must remain HIGH for normal operation.
FIGURE 15. DCP CONNECTION IN SHUTDOWN MODE
Bus Interface Pins
SERIAL CLOCK (SCK)
This is the serial clock input of the SPI serial interface.
SERIAL DATA OUTPUT (SDO)
The SDO is an open drain serial data output pin. During a
read cycle, the data bits are shifted out at the falling edge of
the serial clock SCK, while the CS input is low.
SDO requires an external pull-up resistor for proper
operation.
SERIAL DATA INPUT (SDI)
The SDI is the serial data input pin for the SPI interface. It
receives device address, operation code, wiper address and
data from the SPI external host device. The data bits are
shifted in at the rising edge of the serial clock SCK, while the
CS input is low.
CHIP SELECT (CS)
CS LOW enables the ISL22446, placing it in the active
power mode. A HIGH to LOW transition on CS is required
prior to the start of any operation after power-up. When CS is
HIGH, the ISL22446 is deselected and the SDO pin is at
high impedance, and (unless an internal write cycle is
underway) the device will be in the standby state.
Principles of Operation
The ISL22446 is an integrated circuit incorporating four
DCPs with its associated registers, non-volatile memory and
the SPI serial interface providing direct communication
between host and potentiometers and memory. The resistor
array is comprised of individual resistors connected in
series. At either end of the array and between each resistor
is an electronic switch that transfers the potential at that
point to the wiper.
FIGURE 13. MIDSCALE GLITCH, CODE 3Fh TO 40h
FIGURE 14. LARGE SIGNAL SETTLING TIME
Typical Performance Curves (Continued)
SIGNAL AT WIPER
(WIPER UNLOADED)
WIPER MID POINT MOVEMENT
FROM 3Fh TO 40h
SIGNAL AT WIPER
(WIPER UNLOADED MOVEMENT
FROM 7Fh TO 00h)
SCL
RLi
RWi
RHi
ISL22446
相关PDF资料 |
PDF描述 |
|---|---|
| ISL22449UFV14Z-TK | IC POT DGTL 128TP LN LP 14-TSSOP |
| ISL22511UFB8Z | IC POT DGTL PB 32TP LN LP 8-SOIC |
| ISL22512WFB8Z | IC POT DGTL PB 16TP LN LP 8-SOIC |
| ISL23315WFUZ-TK | IC DGTL POT 256POS 10K 10MSOP |
| ISL23318WFUZ-TK | IC DGTL POT 1CH 10K 10MSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL22446WFRT20Z-TK | 功能描述:数字电位计 IC 128 TAP FL RNG IND QD DCP 20LD 4X4 TQFN RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
| ISL22446WFV20Z | 功能描述:数字电位计 IC 128 TAP FL RNG IND QD DCP 20LD RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
| ISL22446WFV20Z-TK | 功能描述:数字电位计 IC 128 TAP FL RNG IND QD DCP 20LD RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
| ISL22449 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Quad Digitally Controlled Potentiometer |
| ISL22449UFV14Z | 功能描述:IC POT DGTL 128TP LN LP 14-TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数字电位器 系列:XDCP™ 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 接片:32 电阻（欧姆）:50k 电路数:1 温度系数:标准值 50 ppm/°C 存储器类型:易失 接口:3 线串行（芯片选择，递增，增/减） 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 细型，TSOT-23-6 供应商设备封装:TSOT-23-6 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。