参数资料
| 型号： | ISL22446WFRT20Z |
| 厂商： | Intersil |
| 文件页数： | 5/15页 |
| 文件大小： | 0K |
| 描述： | IC POT DGTL 128TP LN LP 20-TQFN |
| 产品培训模块： | Solutions for Industrial Control Applications |
| 标准包装： | 75 |
| 系列： | XDCP™ |
| 接片： | 128 |
| 电阻（欧姆）： | 10k |
| 电路数： | 4 |
| 温度系数： | 标准值 ±50 ppm/°C |
| 存储器类型： | 非易失 |
| 接口： | 4 线 SPI（芯片选择） |
| 电源电压： | 2.7 V ~ 5.5 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-WFQFN 裸露焊盘 |
| 供应商设备封装： | 20-TQFN（4x4） |
| 包装： | 管件 |
13
FN6181.2
September 9, 2009
Applications Information
Communicating with ISL22446
Communication with ISL22446 proceeds using SPI interface
through the ACR (address 1000b), IVRi (addresses 0000b,
0001b, 0010b and 0011b) and WRi (addresses 0000b,
0001b, 0010b and 0011b) registers.
The wiper of the potentiometer is controlled by the WRi
register. Writes and reads can be made directly to these
registers to control and monitor the wiper position without
any non-volatile memory changes. This is done by setting
MSB bit at address 1000b to 1.
The non-volatile IVRi stores the power up value of the wiper.
IVRs are accessible when MSB bit at address 1000b is set
to 0. Writing a new value to the IVRi register will set a new
power up position for the wiper. Also, writing to this register
will load the same value into the corresponding WRi as the
IVRi. Reading from the IVRi will not change the WRi, if its
contents are different.
Examples
A. Writing to the IVR
This sequence will write a new value (77h) to the IVR2
(non-volatile):
Set the ACR (Addr 1000b) for NV write (40h)
Send the ID byte, Instruction Byte, then the Data byte
Set the IVR0 (Addr 0000b) to 77h
Send the ID byte, Instruction Byte, then the Data byte
B. Reading from the WR
This sequence will read the value from the WR3 (volatile):
Write to ACR first to access the WRs
Send the ID byte, Instruction Byte, then the Data byte
Read the data from WR3 (Addr 0011b)
Send the ID byte, Instruction Byte, then Read the Data byte
01 010 000 110 010 000 100 000 0
(Sent to SDI)
01 010 000 110 000 100 111 011 1
(Sent to SDI)
01 010 000 110 010 001 100 000 0
(Sent to SDI)
0 1 0 1 0 0 0 0 1 0 1 1 0 0 1 1 x xxx xxxx
(Out on SDO)
ISL22446
相关PDF资料 |
PDF描述 |
|---|---|
| ISL22449UFV14Z-TK | IC POT DGTL 128TP LN LP 14-TSSOP |
| ISL22511UFB8Z | IC POT DGTL PB 32TP LN LP 8-SOIC |
| ISL22512WFB8Z | IC POT DGTL PB 16TP LN LP 8-SOIC |
| ISL23315WFUZ-TK | IC DGTL POT 256POS 10K 10MSOP |
| ISL23318WFUZ-TK | IC DGTL POT 1CH 10K 10MSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL22446WFRT20Z-TK | 功能描述:数字电位计 IC 128 TAP FL RNG IND QD DCP 20LD 4X4 TQFN RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
| ISL22446WFV20Z | 功能描述:数字电位计 IC 128 TAP FL RNG IND QD DCP 20LD RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
| ISL22446WFV20Z-TK | 功能描述:数字电位计 IC 128 TAP FL RNG IND QD DCP 20LD RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
| ISL22449 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Quad Digitally Controlled Potentiometer |
| ISL22449UFV14Z | 功能描述:IC POT DGTL 128TP LN LP 14-TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数字电位器 系列:XDCP™ 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 接片:32 电阻（欧姆）:50k 电路数:1 温度系数:标准值 50 ppm/°C 存储器类型:易失 接口:3 线串行（芯片选择，递增，增/减） 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 细型，TSOT-23-6 供应商设备封装:TSOT-23-6 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。