参数资料
| 型号： | ISL23315TFRUZ-T7A |
| 厂商： | Intersil |
| 文件页数： | 7/20页 |
| 文件大小： | 0K |
| 描述： | IC DGTL POT 256POS 100K 10TQFN |
| 产品培训模块： | Solutions for Industrial Control Applications |
| 标准包装： | 1 |
| 系列： | XDCP™ |
| 接片： | 256 |
| 电阻（欧姆）： | 100k |
| 电路数： | 1 |
| 温度系数： | 标准值 70 ppm/°C |
| 存储器类型： | 易失 |
| 接口： | I²C（设备位址） |
| 电源电压： | 1.2 V ~ 5.5 V，1.7 V ~ 5.5 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-UFQFN |
| 供应商设备封装： | 10-UTQFN（2.1x1.6） |
| 包装： | 标准包装 |
| 其它名称： | ISL23315TFRUZ-T7ADKR |
ISL23315
15
FN7778.1
August 15, 2011
I2C Serial Interface
The ISL23315 supports an I2C bidirectional bus oriented
protocol. The protocol defines any device that sends data onto
the bus as a transmitter and the receiving device as the receiver.
The device controlling the transfer is a master and the device
being controlled is the slave. The master always initiates data
transfers and provides the clock for both transmit and receive
operations. Therefore, the ISL23315 operates as a slave device
in all applications.
All communication over the I2C interface is conducted by sending
the MSB of each byte of data first.
Protocol Conventions
Data states on the SDA line must change only during SCL LOW
periods. SDA state changes during SCL HIGH are reserved for
indicating START and STOP conditions (see Figure 27). On
power-up of the ISL23315, the SDA pin is in the input mode.
All I2C interface operations must begin with a START condition,
which is a HIGH-to-LOW transition of SDA while SCL is HIGH. The
ISL23315 continuously monitors the SDA and SCL lines for the
START condition and does not respond to any command until this
condition is met (see Figure 27). A START condition is ignored
during the power-up of the device.
All I2C interface operations must be terminated by a STOP
condition, which is a LOW to HIGH transition of SDA while SCL is
HIGH (see Figure 27). A STOP condition at the end of a read
operation or at the end of a write operation places the device in
its standby mode.
An ACK (Acknowledge) is a software convention used to indicate
a successful data transfer. The transmitting device, either master
or slave, releases the SDA bus after transmitting eight bits.
During the ninth clock cycle, the receiver pulls the SDA line LOW
to acknowledge the reception of the eight bits of data
(see Figure 28).
The ISL23315 responds with an ACK after recognition of a START
condition followed by a valid Identification Byte, and once again
after successful receipt of an Address Byte. The ISL23315 also
responds with an ACK after receiving a Data Byte of a write
operation. The master must respond with an ACK after receiving
a Data Byte of a read operation.
A valid Identification Byte contains 10100 as the five MSBs, and
the following two bits matching the logic values present at pins
A1 and A0. The LSB is the Read/Write bit. Its value is “1” for a
Read operation and “0” for a Write operation (see Table 3).
TABLE 3. IDENTIFICATION BYTE FORMAT
FIGURE 26. SHUTDOWN MODE WIPER RESPONSE
POWER-UP
USER PROGRAMMED
MID SCALE = 80H
SHDN ACTIVATED SHDN RELEASED
AFTER SHDN
WIPE
R
VO
LT
AGE,
V
RW
(V
)
SHDN MODE
TIME (s)
WIPER RESTORE TO
THE ORIGINAL POSITION
0
10100
A1
A0
R/W
(MSB)
(LSB)
LOGIC VALUES AT PINS A1 AND A0, RESPECTIVELY
SDA
SCL
START
DATA
STOP
STABLE
CHANGE
DATA
STABLE
FIGURE 27. VALID DATA CHANGES, START AND STOP CONDITIONS
相关PDF资料 |
PDF描述 |
|---|---|
| DS1390U-3+T&R | IC RTC SPI 3WIRE W/CHRGR 10-MSOP |
| VI-J7Y-MZ | CONVERTER MOD DC/DC 3.3V 16.5W |
| DS1393U-18+T&R | IC RTC W/CHARGER 10-USOP |
| DS1391U-33+T&R | IC RTC W/CHARGER 10-USOP |
| VI-J6X-MZ | CONVERTER MOD DC/DC 5.2V 25W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL23315TFRUZ-TK | 功能描述:数字电位计 IC 256 TAP VOLATILE I2C FL RNG INC DCP 21X16 RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
| ISL23315TFUZ | 功能描述:数字电位计 IC 256 TAP VOLATILE I2C DL FL RNG DCP 10LD RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
| ISL23315TFUZ-T7A | 功能描述:数字电位计 IC 256 TAP VOLATILE I2C DL FL RNG DCP 10LD RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
| ISL23315TFUZ-TK | 功能描述:数字电位计 IC 256 TAP VOLATILE I2C DL FL RNG DCP 10LD RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
| ISL23315UFRUZ-T7A | 功能描述:数字电位计 IC 256 TAP VOLATILE I2C FL RNG INC DCP 21X16 RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。