参数资料
| 型号： | ISL23315TFRUZ-T7A |
| 厂商： | Intersil |
| 文件页数： | 9/20页 |
| 文件大小： | 0K |
| 描述： | IC DGTL POT 256POS 100K 10TQFN |
| 产品培训模块： | Solutions for Industrial Control Applications |
| 标准包装： | 1 |
| 系列： | XDCP™ |
| 接片： | 256 |
| 电阻（欧姆）： | 100k |
| 电路数： | 1 |
| 温度系数： | 标准值 70 ppm/°C |
| 存储器类型： | 易失 |
| 接口： | I²C（设备位址） |
| 电源电压： | 1.2 V ~ 5.5 V，1.7 V ~ 5.5 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-UFQFN |
| 供应商设备封装： | 10-UTQFN（2.1x1.6） |
| 包装： | 标准包装 |
| 其它名称： | ISL23315TFRUZ-T7ADKR |
ISL23315
17
FN7778.1
August 15, 2011
Write Operation
A Write operation requires a START condition, followed by a valid
Identification Byte, a valid Address Byte, a Data Byte, and a STOP
condition. After each of the three bytes, the ISL23315 responds
with an ACK. The data is transferred from I2C block to the
corresponding register at the 9th clock of the data byte and
Read Operation
A Read operation consists of a three byte instruction followed by
one or more Data Bytes (see Figure 30). The master initiates the
operation issuing the following sequence: a START, the
Identification byte with the R/W bit set to “0”, an Address Byte, a
second START, and a second Identification byte with the R/W bit
set to “1”. After each of the three bytes, the ISL23315 responds
with an ACK; then the ISL23315 transmits Data Byte. The master
terminates the read operation issuing a NACK (ACK) and a STOP
condition following the last bit of the last Data Byte (see
Figure 30).
Applications Information
VLOGIC Requirements
It is recommended to keep VLOGIC powered all the time during
normal operation. In a case where turning VLOGIC OFF is
necessary, it is recommended to ground the VLOGIC pin of the
ISL23315. Grounding the VLOGIC pin or both VLOGIC and VCC does
not affect other devices on the same bus. It is good practice to
put a 1F cap in parallel to 0.1F as close to the VLOGIC pin as
possible.
VCC Requirements and Placement
It is recommended to put a 1F capacitor in parallel with 0.1F
decoupling capacitor close to the VCC pin.
Wiper Transition
When stepping up through each tap in voltage divider mode,
some tap transition points can result in noticeable voltage
transients, or overshoot/undershoot, resulting from the sudden
transition from a very low impedance “make” to a much higher
impedance “break” within a short period of time (<1s). There
are several code transitions such as 0Fh to 10h, 1Fh to 20h,...,
EFh to FFh, which have higher transient glitch. Note, that all
switching transients will settle well within the settling time as
stated in the datasheet. A small capacitor can be added
externally to reduce the amplitude of these voltage transients.
However, that will also reduce the useful bandwidth of the circuit,
thus may not be a good solution for some applications. It may be
a good idea, in that case, to use fast amplifiers in a signal chain
for fast recovery.
相关PDF资料 |
PDF描述 |
|---|---|
| DS1390U-3+T&R | IC RTC SPI 3WIRE W/CHRGR 10-MSOP |
| VI-J7Y-MZ | CONVERTER MOD DC/DC 3.3V 16.5W |
| DS1393U-18+T&R | IC RTC W/CHARGER 10-USOP |
| DS1391U-33+T&R | IC RTC W/CHARGER 10-USOP |
| VI-J6X-MZ | CONVERTER MOD DC/DC 5.2V 25W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL23315TFRUZ-TK | 功能描述:数字电位计 IC 256 TAP VOLATILE I2C FL RNG INC DCP 21X16 RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
| ISL23315TFUZ | 功能描述:数字电位计 IC 256 TAP VOLATILE I2C DL FL RNG DCP 10LD RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
| ISL23315TFUZ-T7A | 功能描述:数字电位计 IC 256 TAP VOLATILE I2C DL FL RNG DCP 10LD RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
| ISL23315TFUZ-TK | 功能描述:数字电位计 IC 256 TAP VOLATILE I2C DL FL RNG DCP 10LD RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
| ISL23315UFRUZ-T7A | 功能描述:数字电位计 IC 256 TAP VOLATILE I2C FL RNG INC DCP 21X16 RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。