参数资料
| 型号： | ISL23415WFRUZ-T7A |
| 厂商： | Intersil |
| 文件页数： | 8/20页 |
| 文件大小： | 0K |
| 描述： | IC DGTL POT 256POS 10K 10TQFN |
| 产品培训模块： | Solutions for Industrial Control Applications |
| 标准包装： | 1 |
| 系列： | XDCP™ |
| 接片： | 256 |
| 电阻（欧姆）： | 10k |
| 电路数： | 1 |
| 温度系数： | 标准值 175 ppm/°C |
| 存储器类型： | 易失 |
| 接口： | 4 线 SPI（芯片选择） |
| 电源电压： | 1.2 V ~ 5.5 V，1.7 V ~ 5.5 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-UFQFN |
| 供应商设备封装： | 10-UTQFN（2.1x1.6） |
| 包装： | 标准包装 |
| 其它名称： | ISL23415WFRUZ-T7ADKR |
ISL23415
16
FN7780.1
August 16, 2011
Applications Information
Communicating with ISL23415
Communication with ISL23415 proceeds using SPI interface
through the ACR (address 10000b) and WR (addresses 00000b)
registers.
The wiper of the potentiometer is controlled by the WR register.
Writes and reads can be made directly to these register to control
and monitor the wiper position.
Daisy Chain Configuration
When application needs more than one ISL23415, it can
communicate with all of them without additional CS lines by
daisy chaining the DCPs as shown on Figure 29. In Daisy Chain
configuration, the SDO pin of the previous chip is connected to
the SDI pin of the following chip, and each CS and SCK pins are
connected to the corresponding microcontroller pins in parallel,
like regular SPI interface implementation. The Daisy Chain
configuration can also be used for simultaneous setting of
multiple DCPs. Note, the number of daisy chained DCPs is
limited only by the driving capabilities of SCK and CS pins of
microcontroller; for larger number of SPI devices buffering of
SCK and CS lines is required.
Daisy Chain Write Operation
The write operation starts by HIGH-to-LOW transition on CS line,
followed by N number of two bytes write instructions on SDI line
with reversed chain access sequence: the instruction byte + data
byte for the last DCP in chain is going first, as shown in Figure 30,
where N is a number of DCPs in chain. The serial data is going
through DCPs from DCP0 to DCP(N-1) as follow: DCP0 --> DCP1 -->
DCP2 --> ... --> DCP(N-1). The write instruction is executed on the
rising edge of CS for all N DCPs simultaneously.
Daisy Chain Read Operation
The read operation consists of two parts: first, send the read
instructions (N two bytes operation) with valid address; second,
read the requested data while sending NOP instructions (N two
The first part starts by HIGH-to-LOW transition on CS line,
followed by N two bytes read instruction on SDI line with reversed
chain access sequence: the instruction byte + dummy data byte
for the last DCP in chain is going first, followed by LOW-to-HIGH
transition on CS line. The read instructions are executed during
second part of read sequence. It also starts by HIGH-to-LOW
transition on CS line, followed by N number of two bytes NOP
instructions on SDI line and LOW-to-HIGH transition of CS. The
data is read on every even byte during second part of read
sequence while every odd byte contains code 111b followed by
address from which the data is being read.
Wiper Transition
When stepping up through each tap in voltage divider mode,
some tap transition points can result in noticeable voltage
transients, or overshoot/undershoot, resulting from the sudden
transition from a very low impedance “make” to a much higher
impedance “break within a short period of time (<1s). There are
several code transitions such as 0Fh to 10h, 1Fh to 20h,..., EFh to
FFh, which have higher transient glitch. Note, that all switching
transients will settle well within the settling time as stated in the
datasheet. A small capacitor can be added externally to reduce
the amplitude of these voltage transients, but that will also
reduce the useful bandwidth of the circuit, thus may not be a
good solution for some applications. It may be a good idea, in
that case, to use fast amplifiers in a signal chain for fast
recovery.
VLOGIC Requirements
It is recommended to keep VLOGIC powered all the time during
normal operation. In a case where turning VLOGIC OFF is
necessary, it is recommended to ground the VLOGIC pin of the
ISL23415. Grounding the VLOGIC pin or both VLOGIC and VCC does
not affect other devices on the same bus. It is good practice to put
a 1F capacitor in parallel with 0.1F decoupling capacitor close to
the VLOGIC pin.
VCC Requirements and Placement
It is recommended to put a 1F capacitor in parallel with 0.1F
decoupling capacitor close to the VCC pin.
CS
SCK
MOSI
MISO
CS
SCK
SDI
SDO
CS
SCK
SDI
SDO
CS
SCK
SDI
SDO
CS
SCK
SDI
SDO
C
DCP0
DCP1
DCP2
DCP(N-1)
FIGURE 29. DAISY CHAIN CONFIGURATION
N DCP IN A CHAIN
相关PDF资料 |
PDF描述 |
|---|---|
| DS1307Z/T&R | IC RTC SERIAL 512K 8-SOIC |
| DS1302S/T&R | IC TIMEKEEPER T-CHARGE 8-SOIC |
| VI-JN4-MZ | CONVERTER MOD DC/DC 48V 25W |
| ISL23315TFRUZ-T7A | IC DGTL POT 256POS 100K 10TQFN |
| DS1390U-3+T&R | IC RTC SPI 3WIRE W/CHRGR 10-MSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL23415WFRUZ-TK | 功能描述:数字电位计 IC 256 TAP VOLATILE SPI FL RNG INC DCP 21X16 RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
| ISL23415WFUZ | 功能描述:数字电位计 IC 256 TAP VOLATILE SPI DL FL RNG DCP 10LD RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
| ISL23415WFUZ-T7A | 功能描述:数字电位计 IC 256 TAP VOLATILE SPI DL FL RNG DCP 10LD RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
| ISL23415WFUZ-TK | 功能描述:数字电位计 IC 256 TAP VOLATILE SPI DL FL RNG DCP 10LD RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
| ISL23418 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Single, 128-Tap, Low Voltage Digitally Controlled Potentiometer (XDCPa?￠) |
发布紧急采购，3分钟左右您将得到回复。