参数资料
| 型号： | ISL23448UFVZ |
| 厂商： | Intersil |
| 文件页数： | 7/21页 |
| 文件大小： | 0K |
| 描述： | IC DGTL POT 4CH 50K 20TSSOP |
| 产品培训模块： | Solutions for Industrial Control Applications |
| 标准包装： | 740 |
| 系列： | XDCP™ |
| 接片： | 128 |
| 电阻（欧姆）： | 50k |
| 电路数： | 4 |
| 温度系数： | 标准值 65 ppm/°C |
| 存储器类型： | 易失 |
| 接口： | 4 线 SPI（芯片选择） |
| 电源电压： | 1.2 V ~ 5.5 V，1.7 V ~ 5.5 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 20-TSSOP |
| 包装： | 管件 |
ISL23448
15
FN7905.0
August 19, 2011
When the device enters shutdown, all current DCP WR settings are
maintained. When the device exits shutdown, the wipers will return
to the previous WR settings after a short settling time (see
Figure 26).
In shutdown mode, if there is a glitch on the power supply which
causes it to drop below 1.3V for more than 0.2 to 0.4s the
wipers will be RESET to their mid position. This is done to avoid
an undefined state at the wiper outputs.
SPI Serial Interface
The ISL23448 supports an SPI serial protocol, mode 0. The
device is accessed via the SDI input and SDO output with data
clocked in on the rising edge of SCK, and clocked out on the
falling edge of SCK. CS must be LOW during communication with
the ISL23448. The SCK and CS lines are controlled by the host or
master. The ISL23448 operates only as a slave device.
All communication over the SPI interface is conducted by
sending the MSB of each byte of data first.
Protocol Conventions
The SPI protocol contains Instruction Byte followed by one or more
Data Bytes. A valid Instruction Byte contains instruction as the three
MSBs, with the following five register address bits (see Table 3).
The next byte sent to the ISL23448 is the Data Byte.
Table 4 contains a valid instruction set for ISL23448.
If the [R4:R0] bits are zero, one, two or three then the read or write
is to the WRi register. If the [R4:R0] are 10000, then the operation
is to the ACR.
Write Operation
A write operation to the ISL23448 is a two or more bytes
operation. First, it requires that the CS transition from
HIGH-to-LOW. Then, the host sends a valid Instruction Byte,
followed by one or more Data Bytes to the SDI pin. The host
terminates the write operation by pulling the CS pin from
LOW-to-HIGH. Instruction is executed on the rising edge of CS
(see Figure 27).
Read Operation
A Read operation to the ISL23448 is a four byte operation. First,
it requires that the CS transition from HIGH-to-LOW. Then, the
host sends a valid Instruction Byte, followed by a “dummy” Data
Byte, NOP Instruction Byte and another “dummy” Data Byte to
the SDI pin. The SPI host receives the Instruction Byte (instruction
code + register address) and requested Data Byte from the SDO
pin on the rising edge of SCK during the third and fourth bytes,
respectively. The host terminates the read by pulling the CS pin
from LOW-to-HIGH (see Figure 28).
FIGURE 26. SHUTDOWN MODE WIPER RESPONSE
POWER-UP
USER PROGRAMMED
MID SCALE = 40H
SHDN ACTIVATED SHDN RELEASED
AFTER SHDN
WIPE
R
V
O
LT
AGE
,
V
RW
(V
)
SHDN MODE
TIME (s)
WIPER RESTORE TO
THE ORIGINAL POSITION
0
TABLE 3. INSTRUCTION BYTE FORMAT
BIT #
7
654321
0
I2
I1
I0
R4
R3
R2
R1
R0
TABLE 4. INSTRUCTION SET
INSTRUCTION SET
OPERATION
I2
I1
I0
R4
R3
R2
R1
R0
0
XXX
XX
NOP
0
1
XXX
XX
ACR READ
0
1
XXX
XX
ACR WRTE
1
0
R4R3R2R1R0
WRi or ACR READ
1
0
R4R3R2R1R0
WRi or ACR WRTE
Where X means “do not care”.
相关PDF资料 |
PDF描述 |
|---|---|
| MS27505E23F53P | CONN RCPT 53POS BOX MNT W/PINS |
| MS3451W24-22S | CONN RCPT 4POS CBL MNT W/SCKT |
| ISL23448UFRZ | IC DGTL POT 4CH 50K 20QFN |
| MS3451L24-22S | CONN RCPT 4POS CBL MNT W/SCKT |
| MS27466P23B53P | CONN RCPT 53POS WALL MT W/PINS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL23448UFVZ-T7A | 功能描述:数字电位计 IC 128 TAPVOLATILE SPI QUAD RNG IND 20LD RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
| ISL23448UFVZ-TK | 功能描述:数字电位计 IC 128 TAP VOLATILE SPI QD FL RNG DCP 20LD RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
| ISL23448WFRZ | 功能描述:数字电位计 IC 128 TAP VOLATILE SPI QD FL RNG DCP 20LD RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
| ISL23448WFRZ-T7A | 功能描述:数字电位计 IC 128 TAPVOLATILE SPI QUAD RNG IND 20LD RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
| ISL23448WFRZ-TK | 功能描述:数字电位计 IC 128 TAP VOLATILE SPI QD FL RNG DCP 20LD RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。