参数资料
| 型号： | ISL26710IRTZ |
| 厂商： | Intersil |
| 文件页数： | 7/21页 |
| 文件大小： | 0K |
| 描述： | IC ADC 10BIT SAR 1MSPS 8-TDFN |
| 标准包装： | 100 |
| 位数： | 10 |
| 采样率（每秒）： | 1M |
| 数据接口： | 串行，SPI? |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 8.5mW |
| 电压电源： | 单电源 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-WDFN 裸露焊盘 |
| 供应商设备封装： | 8-TDFN（3x3） |
| 包装： | 管件 |
| 输入数目和类型： | 1 个差分，单极 |
ISL26712, ISL26710, ISL26708
15
FN7999.3
September 5, 2012
Converter Operation
The ISL26712, ISL26710 and ISL26708 are designed to
minimize power consumption by only powering up the SAR
comparator during conversion time. When the converter is in
track mode (its sample capacitors are tracking the input signal)
the SAR comparator is powered down. The state of the converter
is dictated by the logic state of CS. When CS is high the SAR
comparator is powered down while the sampling capacitor array
is tracking the input. When CS transitions low, the capacitor array
immediately captures the analog signal that is being tracked.
After CS is taken low, the SCLK pin is toggled 16 times. For the
first 3 clocks, the comparator is powered up and auto-zeroed,
then the SAR decision process is begun. This process uses 12
SCLK cycles for the 12-bit ISL26712. Each SAR decision is
presented to the SDATA output on the next clock cycle after the
SAR decision is performed. The SAR process (12 bits) is
completed on SCLK cycle 15. At this point in time, the SAR
comparator is powered down and the capacitor array is placed
back into Track mode. The last SAR comparator decision is
output from SDATA on the 16th SCLK cycle. When the last data
bit is output from SDATA the output switches to a logic 0 until CS
is taken high, at which time, the SDATA output enters a High-Z
state.
The ISL26710 and ISL26708 will take fewer clock cycles for their
SAR decisions and will output fewer data bits. The extra bits
following the output of the LSB will be logic zeroes.
10- and 8-bit converters respectively.
FIGURE 30. PRECISION VOLTAGE REFERENCE FOR +5V SUPPLY
1
2
3
4
8
7
6
5
DNC
VIN
COMP
GND
DNC
VOUT
TRIM
0.1F
VDD
0.1F
2.5V
VREF
0.1F
BULK
+
5V
ISL21090
ISL267440
ISL267450A
FIGURE 31. VOLTAGE REFERENCE FOR +2.7V TO +3.6V, OR FOR +5V SUPPLY
ISL267817
VDD
0.1F
VREF
0.1F
BULK
+
+2.7V TO +3.6V
ISL21010
GND
VIN
VOUT
1
2
3
0.1F
1.25, 2.048 OR 2.5V
OR +5V
相关PDF资料 |
PDF描述 |
|---|---|
| ISL26710IRTZ-T | IC ADC 10BIT SAR 1MSPS 8-TDFN |
| XRT73LC03AIV | IC LIU E3/DS3/STS-1 3CH 120LQFP |
| MS3101A22-20S | CONN RCPT 9POS FREE HNG W/SCKT |
| IDT72V263L10PFI8 | IC FIFO 8192X18 10NS 80QFP |
| VI-B6B-IV-F1 | CONVERTER MOD DC/DC 95V 150W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL26710IRTZ-T | 功能描述:IC ADC 10BIT SAR 1MSPS 8-TDFN RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:250 系列:- 位数:12 采样率（每秒）:1.8M 数据接口:并联 转换器数目:1 功率耗散（最大）:1.82W 电压电源:模拟和数字 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-LQFP 供应商设备封装:48-LQFP（7x7） 包装:管件 输入数目和类型:2 个单端，单极 |
| ISL26710IRTZ-T7A | 功能描述:模数转换器 - ADC 10 BIT 1MSPS SAR ADC IN 8LD 3x3 RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| ISL26712 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:12-Bit, 10-Bit and 8-Bit, 1MSPS SAR ADCs |
| ISL2671286 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:12-Bit, 20kSPS SAR ADC |
| ISL2671286IBZ | 功能描述:模数转换器 - ADC 12 BIT SINGLE ENDED 20KHZ SAR ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
发布紧急采购，3分钟左右您将得到回复。