参数资料
| 型号： | ISL28288FBZ-T7 |
| 厂商： | Intersil |
| 文件页数： | 4/20页 |
| 文件大小： | 0K |
| 描述： | IC OP AMP DUAL RRIO 8-SOIC |
| 标准包装： | 1,000 |
| 放大器类型： | 通用 |
| 电路数： | 2 |
| 输出类型： | 满摆幅 |
| 转换速率： | 0.14 V/µs |
| 增益带宽积： | 300kHz |
| 电流 - 输入偏压： | 10pA |
| 电压 - 输入偏移： | 50µV |
| 电流 - 电源： | 120µA |
| 电流 - 输出 / 通道： | 31mA |
| 电压 - 电源，单路/双路(±)： | 2.4 V ~ 5.5 V，±1.2 V ~ 2.75 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOIC |
| 包装： | 带卷 (TR) |
ISL28288, ISL28488
12
FN6339.4
July 26, 2011
exceed 0.5V, external series resistors must be used to ensure the
input currents never exceed 5mA (as shown in Figure 37).
Rail-to-Rail Output
A pair of complementary MOSFET devices are used to achieve the
rail-to-rail output swing. The NMOS sinks current to swing the output
in the negative direction. The PMOS sources current to swing the
output in the positive direction. With a 100k
Ω load they will swing to
within 4mV of the positive supply rail and within 3mV of the negative
supply rail.
Enable/Disable Feature
The ISL28288 (only MSOP package option), offers an EN pin that
disables the device when pulled up to at least 2.0V. In the
disabled state (output in a high impedance state), the part
consumes typically 4A. By disabling the part, multiple
ISL28288 parts can be connected together as a MUX. In this
configuration, the outputs are tied together in parallel and a
channel can be selected by the EN pin. The loading effects of the
feedback resistors of the disabled amplifier must be considered
when multiple amplifier outputs are connected together. The EN
pin also has an internal pull-down. If left open, the EN pin will pull
to the negative rail and the device will be enabled by default.
Using Only One Channel
If the application only requires one channel, the user must
configure the unused channel to prevent it from oscillating. The
unused channel will oscillate if the input and output pins are
floating. This will result in higher than expected supply currents
and possible noise injection into the channel being used. The
proper way to prevent this oscillation is to short the output to the
negative input and ground the positive input (as shown in
Figure 38).
Proper Layout Maximizes Performance
To achieve the maximum performance of the high input
impedance and low offset voltage, care should be taken in the
circuit board layout. The PC board surface must remain clean
and free of moisture to avoid leakage currents between adjacent
traces. Surface coating of the circuit board will reduce surface
moisture and provide a humidity barrier, reducing parasitic
resistance on the board.
Current Limiting
The ISL28288 has no internal current-limiting circuitry. If the
output is shorted, it is possible to exceed the Absolute Maximum
Rating for output current or power dissipation, potentially
resulting in the destruction of the device.
Power Dissipation
It is possible to exceed the +150°C maximum junction
temperatures under certain load and power-supply conditions. It
is therefore important to calculate the maximum junction
temperature (TJMAX) for all applications to determine if power
supply voltages, load conditions, or package type need to be
modified to remain in the safe operating area. These parameters
are related in Equation 1:
where:
PDMAXTOTAL is the sum of the maximum power dissipation of
each amplifier in the package (PDMAX)
where:
TMAX = Maximum ambient temperature
θJA = Thermal resistance of the package
PDMAX = Maximum power dissipation of 1 amplifier
VS = Supply voltage (Magnitude of V+ and V-)
IMAX = Maximum supply current of 1 amplifier
VOUTMAX = Maximum output voltage swing of the application
RL = Load resistance
Application Circuits
THERMOCOUPLE AMPLIFIER
Thermocouples are the most popular temperature-sensing
device because of their low cost, interchangeability, and ability to
measure a wide range of temperatures. The ISL28x88 (see
Figure 39) is used to convert the differential thermocouple
voltage into single-ended signal with 10X gain. The amplifier’s
rail-to-rail input characteristic allows the thermocouple to be
biased at ground and the amplifier to run from a single 5V
supply.
FIGURE 37. INPUT ESD DIODE CURRENT LIMITING - UNITY GAIN
-
+
RIN
RL
VIN
VOUT
V+
V-
FIGURE 38. PREVENTING OSCILLATIONS IN UNUSED CHANNELS
-
+
ISL28288
TJMAX
TMAX θJAxPDMAXTOTAL
()
+
=
(EQ. 1)
PDMAX
2*VS ISMAX VS
(
- VOUTMAX)
VOUTMAX
RL
------------------------
×
+
×
=
(EQ. 2)
相关PDF资料 |
PDF描述 |
|---|---|
| 108477064001025 | CONN HEADER INVRTD 64POS STR |
| TLC2272CPWG4 | IC OPAMP GP R-R 2.25MHZ 8TSSOP |
| SMF11AT1G | TVS ZENER 200W 11V SOD123FL |
| SMF10AT1G | TVS ZENER 200W 10V SOD123FL |
| SMF7.5AT1G | IC TVS ZENER 200W 7.5V SOD123FL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL28288FUZ | 功能描述:IC OP AMP DUAL RRIO 10-MSOP RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 其它有关文件:TS1854A View All Specifications 标准包装:50 系列:- 放大器类型:通用 电路数:4 输出类型:满摆幅 转换速率:0.25 V/µs 增益带宽积:630kHz -3db带宽:- 电流 - 输入偏压:16nA 电压 - 输入偏移:1000µV 电流 - 电源:162µA 电流 - 输出 / 通道:48mA 电压 - 电源，单路/双路(±):1.8 V ~ 6 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:14-SOIC（0.154"，3.90mm 宽） 供应商设备封装:14-SO 包装:管件 |
| ISL28288FUZ-T7 | 功能描述:IC OP AMP DUAL RRIO 10-MSOP RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:500 系列:- 放大器类型:通用 电路数:4 输出类型:- 转换速率:2 V/µs 增益带宽积:5MHz -3db带宽:- 电流 - 输入偏压:100nA 电压 - 输入偏移:1500µV 电流 - 电源:1.7mA 电流 - 输出 / 通道:100mA 电压 - 电源，单路/双路(±):4 V ~ 36 V，±2 V ~ 18 V 工作温度:-40°C ~ 85°C 安装类型:通孔 封装/外壳:14-DIP（0.300"，7.62mm） 供应商设备封装:14-PDIP 包装:管件 产品目录页面:1130 (CN2011-ZH PDF) 其它名称:MC33179PGOS |
| ISL28290 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Rail-to-Rail Output, Op Amp |
| ISL28290EVAL1Z | 功能描述:EVALUATION BOARD FOR ISL28290 RoHS:是 类别:编程器，开发系统 >> 评估板 - 运算放大器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- |
| ISL28290FBZ | 功能描述:IC OP AMP R-R DUAL ULN 8-SOIC RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:75 系列:MicroAmplifier™ 放大器类型:通用 电路数:1 输出类型:满摆幅 转换速率:0.03 V/µs 增益带宽积:100kHz -3db带宽:- 电流 - 输入偏压:1pA 电压 - 输入偏移:60µV 电流 - 电源:20µA 电流 - 输出 / 通道:5mA 电压 - 电源，单路/双路(±):2.3 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商设备封装:8-SOIC 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。