参数资料
型号: ISL3873AIK
厂商: INTERSIL CORP
元件分类: 微控制器/微处理器
英文描述: RES 0805 1/8W 5% 1.2KOHM
中文描述: 1 CHANNEL(S), 11M bps, LOCAL AREA NETWORK CONTROLLER, PBGA192
封装: 14 X 14 MM, PLASTIC, BGA-192
文件页数: 15/42页
文件大小: 778K
代理商: ISL3873AIK
15
USB Port
The USB interface implemented in the ISL3873A Is
compatible with the Universal Serial Bus Specification
Revision 1.1. dated September 23, 1998, which is available
from the USB Implementers’ Forum at
http://www.usb.org/
.
The USB supports 4 endpoints.
One Communications Class control endpoint for interface
management;
One Communications Class interrupt endpoint for
signalling interrupts to the host; and,
Two Bulk endpoints for transfer of encapsulated NDIS
functions to and from the host.
The USB along with USB support firmware provides an
alternate host interface for attaching an 802.11{b} WLAN
adapter to a host computer. This interface does not provide
“wireless USB” where USB packets are sent on the wireless
medium due to timing constraints in the USB protocol.
USB+ and USB- are the differential pair signals provided for
the user. These signals are capable of directly driving a USB
cable.
USB_DETECT is a 5V tolerant input to the ISL3873A device.
It is used to signal the MAC processor that a USB cable is
attached to the unit.
Complete details on the USB firmware for controlling this
port can be obtained by contacting the factory directly.
Power Sequencing
The ISL3873A provides a number of firmware controlled port
pins that are used for controlling the power sequencing and
other functions in the front end and baseband processor
components of the radio.
Packet transmission requires precise control of the radio.
Ideally, energy at the antenna ceases immediately after the
last symbol of information has been transmitted while
minimizing spurious radiation. To this end, the
transmit/receive switch is used to smoothly control the power
output. It's also important to apply appropriate modulation to
the PA while it is active to minimize radiation of CW signals.
Signaling sequences for the beginning and end of normal
transmissions are illustrated in Figure 10. Table 1 lists
applicable delays associated with these control signals.
A transmission begins with PE2 and an internal signal
(TX_PE) to the Baseband processor as shown in Figure 10.
This enable activates the transmit state machine in the BBP
and the upconverter in the ISL3783. This starts the
modulated signal flowing to the PA which is turned on by
PA_PE once the drive signal is available. The PA power
ramps up and the power control loop becomes active and
stabilizes. Lastly, the transmit/receive switch is configured
for transmission via the differential pair TR_SW and
TR_SW_BAR. Delays for these signals related to the
initiation of transmission are referenced to PE2. The
switching of the T/R switch after the PA is enabled is done to
minimize RF spurious radiation. While it is not usual practice
to switch the T/R switch while RF is on, in this case it
suppresses spurious by employing the 20dB attenuation of
the switch until the PA turn-on or turn-off transients have died.
After the final data bit has been clocked out of the MAC it waits
for an internal control signal (TX_READY) from the Baseband
processor. This signals that the BBP has modulated the final
information-rich symbol. After allowing time for that symbol to
exit the antenna, the MAC de-asserts TR_SW and
TR_SW_BAR to shut off transmission and lowers PA_PE
followed by PE2 going high. Delays for these signals related to
the termination of transmission are referenced to the rising
edge of PE2. The baseband processor also internally extends
the transmission of data bits for a sufficient time to insure that it
outputs the final bits
.
FIGURE 9. BLOCK DIAGRAM OF A BUFFER ACCESS PATH
BUFFER DESCRIPTOR
ACCESS (FIRMWARE)
ALLOCATE/
DEALLOCATE
REQUEST
BLOCK
OFFSET
VIRTUAL
FRAME BUFFER
DATA PORT
PRE-READ/
POST-WRITE
OFFSET CENTER
HOST
BUS
STATUS
HEADER
DATA
BUFFER
MEMORY
A
FID
D
ISL3873A
相关PDF资料
PDF描述
ISL3874IK96 Wireless LAN Integrated Medium Access Controller with Baseband Processor with Mini-PCI
ISL3874 Wireless LAN Integrated Medium Access Controller with Baseband Processor with Mini-PCI
ISL3874IK Wireless LAN Integrated Medium Access Controller with Baseband Processor with Mini-PCI
ISL39300A-DAPDK-CD PRISM 54Mbps Wireless Local Area Network Access Point
ISL39300A-DAPDK PRISM 54Mbps Wireless Local Area Network Access Point
相关代理商/技术参数
参数描述
ISL3873AIK-TK 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Wireless LAN Integrated Medium Access Controller with Baseband Processor
ISL3873BIK 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:Intersil Corporation 功能描述:
ISL3873BIK-TK 制造商:Intersil Corporation 功能描述:1 CHANNEL(S), 11M bps, LOCAL AREA NETWORK CONTROLLER, PBGA192
ISL3873IK 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Wireless LAN Integrated Medium Access Controller with Baseband Processor
ISL3873IK96 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Wireless LAN Integrated Medium Access Controller with Baseband Processor