- 您现在的位置：买卖IC网 > PDF目录11791 > ISL54102ACQZ (Intersil)IC TMDS REGEN W/MUX 128-MQFP PDF资料下载
参数资料
| 型号： | ISL54102ACQZ |
| 厂商： | Intersil |
| 文件页数： | 5/21页 |
| 文件大小： | 0K |
| 描述： | IC TMDS REGEN W/MUX 128-MQFP |
| 标准包装： | 66 |
| 应用： | 多媒体显示器，测试设备 |
| 接口： | I²C |
| 电源电压： | 3 V ~ 3.6 V |
| 封装/外壳： | 128-BFQFP |
| 供应商设备封装： | 128-MQFP（14x20） |
| 包装： | 托盘 |
| 安装类型： | 表面贴装 |
| 产品目录页面： | 1244 (CN2011-ZH PDF) |
13
FN6725.0
June 17, 2008
Application Information
The ISL54100A, ISL54101A, and ISL54102A are TMDS
regenerators, locking to the incoming DVI or HDMI signal
with triple Clock Data Recovery units (CDRs) and a Phase
Locked Loop (PLL). The PLL generates a low jitter pixel
clock from the incoming TMDS clock. The TMDS data
signals are equalized, sliced by the CDR, re-aligned to the
PLL clock, and sent out the TMDS outputs. The ISL54100A
and ISL54102A also include an input multiplexer.
Compatibility With the ISL5410x Family
The ISL54100A and ISL54102A are plug-in and backwards
compatible with the ISL54100 and ISL54102 in every
respect except one: the CH_SEL pins.
The CH_SEL pins on the ISL54100 and ISL54102 are
bi-directional. They can be used as inputs to externally
chose which channel is selected, or they can be used as
outputs to indicate which channel has been selected (either
via I2C programming or automatic selection).
However the CH_SEL pins on the ISL54100A and
ISL54102A are inputs only. When channel selection is done
via I2C programming or automatically, these pins are
floating, and should be pulled to ground via 47k resistors.
The ISL54101A does not have any CH_SEL pins and is
therefore 100% plug-in and backwards compatible with the
ISL54100.
Multiplexer Operation
The ISL54100A and ISL54102A have 4:1 and 2:1
(respectively) input multiplexers. After power-up or a
hardware reset, the IC defaults to hardware channel
selection, using the AUTO_CH_SEL and CH_SEL_x pins. If
AUTO_CH_SEL is pulled high, the highest priority channel
with an active TMDS clock will be automatically selected
(Channel A = highest priority, B = second highest priority,
C = second lowest, and D = lowest priority). If, for example,
a DVD player is attached to Channel A, a set-top-box (STB)
is attached to Channel B, and a video game is attached to
Channel C, the DVD player will have the highest priority,
overriding the STB and the video game whenever the DVD
player is transmitting a TMDS clock. Likewise, the STB will
have higher priority than the video game. Table 1 shows the
auto channel selection priority matrix.
In the auto channel select mode, the selected channel can
be determined by reading register 0x02 bits 1:0.
If manual channel selection is desired, the AUTO_CH_SEL
pin should be tied to ground and the CH_SEL_x pins used to
select the desired channel.
The input multiplexer can also be controlled by software via
the I2C interface. Software control is initiated by writing a 0 to
the Hardware Channel Select bit (bit 3 of register 0x02). In
this case, the Auto Channel Select bit (bit 2 of register 0x02)
and the Channel Select bits (bits 0 and 1 of register 0x02)
perform the same functions as the external pins described
above. In the Auto Channel Select mode, the Channel
Select bits are read only, indicating the currently selected
channel. In the Manual Channel Select mode, the Channel
Select bits are read/write, and used to select the channel.
Activity Detection
A channel is considered active using one of two methods. The
original default activity detect method (register 0x03b4 = 1) is
to measure the common mode of the TMDS clock input for
each channel. If the common mode is 3.3V, it indicates that
there is nothing connected to that input, or that whatever is
connected is turned off (inactive). This has been found to be
relatively unreliable, particularly with weak signals.
The preferred method of activity detection is looking for an
active AC signal on the TMDS clock input for that channel
(register 0x03b4 = 1). This is more robust, however
disconnected inputs will cause both inputs to the differential
receiver to be the same level - 3.3V. If the offset error of the
differential TMDS receiver is very small, the receiver can not
resolve a 1 or a 0 and will randomly switch between states,
which may be detected as an active clock. Register 0x03 bits
5 and 6 allow a 10mV or 20mV offset to be added to the input
stage of the clock inputs, eliminating this problem. This offset
will slightly reduce the sensitivity of TMDS receiver for the
clock lines, but since the clock signals are much lower
frequency than the data, they will not be nearly as
attenuated, so this is not a problem in practice.
Again, using the AC activity detection method (register
0x03b4 = 0) is recommended.
Rx Equalization
Registers 0x07 and 0x08 control the amount of equalization
applied to the TMDS inputs, with 4 bits of control for each
channel. The equalization range available is from a minimum
of 1dB boost to a maximum of 13dB at 800MHz, in 0.8dB
increments. Ideally, the equalization is adjusted in the final
application to provide optimal performance with the specific
DVI/HDMI transmitter and cable used. In general, the
amount of equalization required is proportional to the cable
length. If the equalization must be fixed (can not be adjusted
in the final application), an equalization setting of 0xA works
well with short cables as well as medium to longer cables.
TABLE 1. AUTO CHANNEL SELECTION PRIORITIES
(ISL54102A OPTIONS IN BLUE)
CHANNEL A CHANNEL B CHANNEL C CHANNEL D OUTPUT
Inactive
Active
Don’t Care
Channel A
Inactive
Active
Don’t Care
Channel B
Inactive
Active
Don’t Care
Channel C
Inactive
Active
Channel D
ISL54100A, ISL54101A, ISL54102A
相关PDF资料 |
PDF描述 |
|---|---|
| ISL54102CQZ | IC TMDS REGEN W/MUX 128MQFP |
| IA186ES-PTQ100I-R-03 | IC MCU 8/16BIT 40MHZ 100TQFP |
| PI7C8152BMAE | IC PCI-PCI BRIDGE 2PORT 160-MQFP |
| DS80C310-MCG+ | IC MCU HI SPEED 25MHZ 40-DIP |
| MS27468E21B41S | CONN RCPT 41POS JAM NUT W/SCKT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL54102CQZ | 功能描述:IC TMDS REGEN W/MUX 128MQFP RoHS:是 类别:集成电路 (IC) >> 接口 - 专用 系列:- 特色产品:NXP - I2C Interface 标准包装:1 系列:- 应用:2 通道 I²C 多路复用器 接口:I²C，SM 总线 电源电压:2.3 V ~ 5.5 V 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:16-TSSOP 包装:剪切带 (CT) 安装类型:表面贴装 产品目录页面:825 (CN2011-ZH PDF) 其它名称:568-1854-1 |
| ISL54103 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:DDC Accelerator (DDCA) |
| ISL54103IHZ-T7 | 功能描述:接口 - 专用 ISL55016IRTZFREE DIF GAIN BLOCK(75OHM ZIN RoHS:否 制造商:Texas Instruments 产品类型:1080p60 Image Sensor Receiver 工作电源电压:1.8 V 电源电流:89 mA 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:BGA-59 |
| ISL54103IHZ-T7A | 功能描述:接口 - 专用 ISL55020IRZ FL DIFFR CFA W/LW DISTORTIO RoHS:否 制造商:Texas Instruments 产品类型:1080p60 Image Sensor Receiver 工作电源电压:1.8 V 电源电流:89 mA 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:BGA-59 |
| ISL54105A | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:TMDS Regenerator |
发布紧急采购，3分钟左右您将得到回复。