- 您现在的位置：买卖IC网 > PDF目录11343 > ISL54209IRUZ-T7A (Intersil)IC USB SWITCH DUAL SPDT 10UTQFN PDF资料下载
参数资料
| 型号： | ISL54209IRUZ-T7A |
| 厂商： | Intersil |
| 文件页数： | 3/19页 |
| 文件大小： | 0K |
| 描述： | IC USB SWITCH DUAL SPDT 10UTQFN |
| 标准包装： | 1 |
| 功能： | USB 开关 |
| 电路： | 2 x SPDT - NO |
| 导通状态电阻： | 20 欧姆 |
| 电压电源： | 单电源 |
| 电压 - 电源，单路/双路(±)： | 2.5 V ~ 5 V |
| 电流 - 电源： | 7µA |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-UFQFN |
| 供应商设备封装： | 10-UTQFN（2.1x1.6） |
| 包装： | 标准包装 |
| 其它名称： | ISL54209IRUZ-T7ADKR |
11
FN6627.4
June 10, 2010
Detailed Description
The ISL54209 device is a dual single pole/double throw
(SPDT) analog switch that operates from a single DC
power supply in the range of 2.5V to 5.0V. It was
designed to function as a dual 2 to 1 multiplexer to select
between USB differential data signals and audio L and R
stereo signals. It comes in tiny TQFN and TDFN
packages for use in MP3 players, PDAs, cellular phones
and other personal media players.
The part consists of two 2.5Ω audio switches and two 5Ω
USB switches. The audio switches can accept signals that
swing below ground. They were designed to pass audio
left and right stereo signals, that are ground referenced,
with minimal distortion. The USB switches were designed
to pass high-speed USB differential data signals with
minimal edge and phase distortion.
The ISL54209 was specifically designed for MP3 players,
personal media players and cellular phone applications
that need to combine the audio headphone jack and the
USB data connector into a single shared connector,
thereby saving space and component cost. “Typical
The ISL54209 has a single logic control pin (IN) that
selects between the audio switches and the USB
switches. This pin can be driven Low or High to switch
between the audio CODEC drivers and USB transceiver of
the MP3 player or cellular phone. The ISL54209 also
contains a logic control pin (CTRL) that when driven Low
while IN is Low, opens all switches and puts the part into
a low power state, drawing typically 1nA of IDD current.
Detailed descriptions of the two types of switches are
provided in the following sections.
Audio Switches
The two audio switches (L, R) are 2.5Ω switches that can
pass signals that swing below ground by as much as
1.5V. They were designed to pass ground reference
stereo signals with minimal insertion loss and very low
distortion over a ±1V signal range.
Crosstalk between the audio channels is -110dB over the
audio band. Crosstalk between the audio channel and
USB channel is -95dB at 100kHz. These switches have
excellent OFF-isolation, 114dB, over the audio band with
a 32Ω load.
Over a signal range of ±1V (0.707VRMS) with
VDD > 2.7V, these switches have an extremely low rON
resistance variation. They can pass ground referenced
audio signals with very low distortion (<0.06% THD+N)
when delivering 15.6mW into a 32Ω headphone speaker
These switches are bi-directional switches. In typical
applications, the audio drivers would be connected at the
L and R side of the switch and the speaker loads would
be connected at the COM side of the switch.
The audio switches are active (turned ON) whenever the
IN voltage is ≤ 0.5V or floating and the CTRL voltage ≥ to
1.4V.
USB Switches
The two USB switches (D+, D-) are bidirectional switches
that can pass rail-to-rail signals. When powered with a
3.3V supply, these switches have a nominal rON of 5Ω
over the signal range of 0V to 400mV with a rON flatness
of 0.45Ω. The rON matching between the D+ and D-
switches over this signal range is only 0.05Ω ensuring
minimal impact by the switches to USB high speed signal
transitions. As the signal level increases, the rON
resistance increases. At a signal level of 3.3V, the switch
resistance is nominally 25Ω.
The USB switches were specifically designed to pass USB
2.0 high-speed (480Mbps) differential signals typically in
the range of 0V to 400mV. They have low capacitance
and high bandwidth to pass the USB high-speed signals
with minimum edge and phase distortion to meet USB
2.0 high speed signal quality specifications. See
Figure 12.
The USB switches can also pass USB full-speed signals
(12Mbps) with minimal distortion and meet all the USB
requirements for USB 2.0 full-speed signaling. See
Figure 13 for Full-speed Eye Pattern taken with switch in
the signal path.
The USB switches are active (turned ON) whenever the
IN voltage is ≥ to 1.4V.
COM+, COM-, 1D-, 1D+, 2D-, AND 2D+ ARE
OVERVOLTAGE TOLERANT UP TO 5.5V AND
DOWN TO -1.5V
For normal operation, the signal range for the USB
switches is from -1V to VDD. During normal operation,
the signal voltage at D- and D+ should not be allowed
to exceed the VDD voltage rail or go below ground by
more than -1.0V. However, the ISL54209, with a VDD
supply voltage in the range of 0V to 5.0V, can
withstand an overvoltage of up to 5.5V or down to
-1.5V applied at its COM pins (COM-, COM+) and/or
USB signal pins (1D-, 1D+, 2D-, 2D+) without
damage. In this overvoltage condition, the part draws
<1mA of current and causes no stress to the IC.
Note: When in the overvoltage state, the fault voltage
at a COM pin will pass thru the USB switch to the signal
side of the switch, so the media player’s USB
transceiver must have protection circuitry to protect it
from damage.
ISL54209 Operation
The following will discuss using the ISL54209 in the
VDD SUPPLY
The DC power supply connected at VDD pin provides the
required bias voltage for proper switch operation. The
ISL54209
相关PDF资料 |
PDF描述 |
|---|---|
| PIC16LF874-04/P | IC MCU FLASH 4KX14 EE A/D 40DIP |
| PIC16C621-20/SO | IC MCU OTP 1KX14 COMP 18SOIC |
| PIC16F873T-20/SO | IC MCU FLASH 4KX14 EE 28SOIC |
| PIC16F767-E/ML | IC PIC MCU FLASH 8KX14 28QFN |
| DEHR33A681KB2B | CAP CER 680PF 1KV 10% RADIAL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL54210 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:MP3/USB 2.0 High Speed Switch with Negative Signal Handling/Click and Pop Suppression |
| ISL54210EVAL1Z | 功能描述:EVALUATION BOARD FOR ISL54210 RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:PCI Express® (PCIe) 主要目的:接口，收发器，PCI Express 嵌入式:- 已用 IC / 零件:DS80PCI800 主要属性:- 次要属性:- 已供物品:板 |
| ISL54210IRTZ | 功能描述:IC SWITCH DUAL SPDT HS 10-TDFN RoHS:是 类别:集成电路 (IC) >> 接口 - 模拟开关，多路复用器，多路分解器 系列:- 应用说明:Ultrasound Imaging Systems Application Note 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:250 系列:- 功能:开关 电路:单刀单掷 导通状态电阻:48 欧姆 电压电源:单电源 电压 - 电源，单路/双路(±):2.7 V ~ 5.5 V 电流 - 电源:5µA 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:48-LQFP 供应商设备封装:48-LQFP（7x7） 包装:托盘 |
| ISL54210IRTZ-T | 功能描述:IC SWITCH DUAL SPDT HS 10-TDFN RoHS:是 类别:集成电路 (IC) >> 接口 - 模拟开关，多路复用器，多路分解器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:36 系列:- 功能:多路复用器 电路:2 x 4:1 导通状态电阻:75 欧姆 电压电源:单/双电源 电压 - 电源，单路/双路(±):2 V ~ 12 V，±2 V ~ 6 V 电流 - 电源:- 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:20-SOIC（0.295"，7.50mm 宽） 供应商设备封装:20-SOIC W 包装:管件 |
| ISL54210IRUZ-T | 功能描述:IC SWITCH HS DUAL SPDT 10-TQFN RoHS:是 类别:集成电路 (IC) >> 接口 - 模拟开关，多路复用器，多路分解器 系列:- 标准包装:2,500 系列:- 功能:视频交叉点开关 电路:1 x 8:6 导通状态电阻:- 电压电源:单电源 电压 - 电源，单路/双路(±):3.135 V ~ 5.25 V 电流 - 电源:55mA 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:24-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:24-TSSOP 包装:带卷 (TR) 产品目录页面:1214 (CN2011-ZH PDF) 其它名称:FMS6502MTC24XTR |
发布紧急采购，3分钟左右您将得到回复。