参数资料
| 型号： | ISL54225IRUZ-T7A |
| 厂商： | Intersil |
| 文件页数： | 3/18页 |
| 文件大小： | 0K |
| 描述： | IC MULTIPLEXER DUAL 2:1 10TQFN |
| 标准包装： | 1 |
| 功能： | 多路复用器 |
| 电路： | 2 x 2:1 |
| 导通状态电阻： | 20 欧姆 |
| 电压电源： | 单电源 |
| 电压 - 电源，单路/双路(±)： | 2.7 V ~ 5.25 V |
| 电流 - 电源： | 45µA |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-UFQFN |
| 供应商设备封装： | 10-UTQFN（1.8x1.40） |
| 包装： | 标准包装 |
| 其它名称： | ISL54225IRUZ-T7ADKR |
11
FN7627.0
July 2, 2010
LOGIC CONTROL
The state of the ISL54225 device is determined by the
voltage at the SEL pin and the OE pin. SEL is only active
when the OE pin is logic “0” (Low). Refer to “Truth Table”
The ISL54225 logic pins are designed to minimize
current consumption when the logic control voltage is
lower than the VDD supply voltage. With VDD = 3.6V and
logic pins at 1.4V, the part typically draws only 25A.
With VDD = 4.3V and logic pins at 2.6V, the part typically
draws only 35A. Driving the logic pins to the VDD supply
rail minimizes power consumption.
The SEL pin and OE pin have special circuitry that allows
them to be driven with a voltage higher than the VDD
supply voltage. These pins can be driven up to 5.25V
with a VDD supply in the range of 2.7V to 5.25V.
The SEL pin is internally pulled low through 4MΩ resistor
to ground. The OE pin is internally pulled high through a
4MΩ resistor to VDD. These pins can be tri-stated by a
Processor or left floating.
Logic Control Voltage Levels
HSD1 USB Channel
If the SEL pin = Logic “0” and the OE pin = Logic “0”,
high-speed Channel 1 will be ON. The HSD1- and HSD1+
switches are ON and the HSD2- and HSD2+ switches are
OFF (high impedance).
When a computer or USB hub is plugged into the
common USB connector and Channel 1 is active, a link
will be established between the USB 1 transceiver section
of the media player and the computer. The device will be
able to transmit and receive data from the computer.
HSD2 USB Channel
If the SEL pin = Logic “1” and the OE pin = Logic “0”,
high-speed Channel 2 will be ON. The HSD2- and HSD2+
switches are ON and the HSD1- and HSD1+ switches are
OFF (high impedance).
When a USB cable from a computer or USB hub is
connected at the common USB connector and the part
has Channel 2 active, a link will be established between
the USB 2 driver section of the media player and the
computer. The device will be able to transmit and receive
data from the computer.
All Switches OFF Mode
If the SEL pin = Logic “0” and the OE pin = Logic “1”, all of
the switches will turn OFF (high impedance) and the part
will be put in a low power mode. In this mode, the part
draws only 10A (max) of current across the operating
temperature range. In the low power mode, the persistence
checking of the OVP circuitry is de-activated.
If the SEL pin = Logic “1” and the OE pin = Logic “1”, all
of the switches will turn OFF (high impedance). In this
state the complete OTV circuitry is activated.
The all OFF state can be used to switch between the two
USB sections of the media player. When disconnecting
from one USB device to the other USB device, you can
momentarily put the ISL54225 switch in the “all off”
state in order to get the computer to disconnect from
the one device so it can properly connect to the other
USB device when that channel is turned ON.
Whenever the ISL54225 senses a fault condition on the
COM pins, all switches will be turned OFF regardless of
the voltage levels at the SEL and OE pins.
USB 2.0 VBUS Short Requirements
The USB specification in section 7.1.1 states a USB
device must be able to withstand a VBUS short (4.4V to
5.25V) or a -1V short to the D+ or D- signal lines when
the device is either powered off or powered on for at
least 24 hours.
The ISL54225 part has special power-off protection and
OVP detection circuitry to meet these short circuit
requirements. This circuitry allows the ISL54225 to
provide protection to the USB down-stream transceivers
connected at its signal pins (HS1D-, HS1D+, HS2D-,
HS2D+) to meet the USB specification short circuit
requirements.
The power-off protection and OVP circuitry allows the COM
pins (D-, D+) to be driven up to 5.25V or down to -5V while
the VDD supply voltage is in the range of 0V to 5.25V. In
these overvoltage conditions with a 500Ω external VDD
resistor, the part draws < 55A of current into the COM pins
and causes no stress/damage to the IC. In addition, all
switches are OFF and the shorted VBUS voltage will be
isolated from getting through to the other side of the switch
channels, thereby protecting the USB transceivers.
TABLE 2. LOGIC CONTROL VOLTAGE LEVELS
VDD SUPPLY
RANGE
LOGIC = “0” (LOW)
LOGIC = “1”
(HIGH)
OE
SEL
OE
SEL
2.7V to 3.6V
≤ 0.5V
or
floating
≥1.4V
or
floating
≥1.4V
3.7V to 4.2V
≤ 0.7V
or
floating
≥1.7V
or
floating
≥1.7V
4.3V to 5.25V
≤ 0.8V
or
floating
≥2.0V
or
floating
≥2.0V
ISL54225
相关PDF资料 |
PDF描述 |
|---|---|
| ISL54226IRUZ-T | IC USB SWITCH DPST OVP 8TQFN |
| ISL54227IRTZ | IC USB SWITCH DUAL DPST 10TDFN |
| ISL54228IRUZ-T | IC USB SWITCH DPST OVP 8TQFN |
| ISL54230IRTZ | IC SWITCH QUAD DPDT 32TQFN |
| ISL54233IRUZ-T | IC INTERFACE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL54226 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:High-Speed USB 2.0 (480Mbps) DPST Switch with Overvoltage Protection (OVP) and Dedicated Charger Port Detection |
| ISL54226_10 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:High-Speed USB 2.0 (480Mbps) DPST Switch with Overvoltage Protection (OVP) and Dedicated Charger Port Detection |
| ISL54226IRTZEVAL1Z | 功能描述:BOARD EVAL FOR ISL5426A MUX RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:PCI Express® (PCIe) 主要目的:接口，收发器，PCI Express 嵌入式:- 已用 IC / 零件:DS80PCI800 主要属性:- 次要属性:- 已供物品:板 |
| ISL54226IRTZ-T | 功能描述:IC USB SWITCH DPST OVP 8TDFN RoHS:是 类别:集成电路 (IC) >> 接口 - 模拟开关，多路复用器，多路分解器 系列:- 其它有关文件:STG4159 View All Specifications 标准包装:5,000 系列:- 功能:开关 电路:1 x SPDT 导通状态电阻:300 毫欧 电压电源:双电源 电压 - 电源，单路/双路(±):±1.65 V ~ 4.8 V 电流 - 电源:50nA 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:7-WFBGA，FCBGA 供应商设备封装:7-覆晶 包装:带卷 (TR) |
| ISL54226IRTZ-T7A | 功能描述:IC USB SWITCH DPST OVP 8TDFN RoHS:是 类别:集成电路 (IC) >> 接口 - 模拟开关，多路复用器，多路分解器 系列:- 应用说明:Ultrasound Imaging Systems Application Note 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:250 系列:- 功能:开关 电路:单刀单掷 导通状态电阻:48 欧姆 电压电源:单电源 电压 - 电源，单路/双路(±):2.7 V ~ 5.5 V 电流 - 电源:5µA 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:48-LQFP 供应商设备封装:48-LQFP（7x7） 包装:托盘 |
发布紧急采购，3分钟左右您将得到回复。