- 您现在的位置：买卖IC网 > PDF目录11343 > ISL54228IRUZ-T7A (Intersil)IC USB SWITCH DPST OVP 8TQFN PDF资料下载
参数资料
| 型号： | ISL54228IRUZ-T7A |
| 厂商： | Intersil |
| 文件页数： | 2/17页 |
| 文件大小： | 0K |
| 描述： | IC USB SWITCH DPST OVP 8TQFN |
| 标准包装： | 1 |
| 功能： | 开关 |
| 电路： | 2 x SPST |
| 导通状态电阻： | 17 欧姆 |
| 电压电源： | 单电源 |
| 电压 - 电源，单路/双路(±)： | 2.7 V ~ 5.25 V |
| 电流 - 电源： | 45µA |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-XFQFN |
| 供应商设备封装： | 8-UTQFN（1.2x1.4） |
| 包装： | 标准包装 |
| 其它名称： | ISL54228IRUZ-T7ADKR |
ISL54228
10
FN7628.0
July 29, 2010
distortion and meet all the USB requirements for USB
2.0 full-speed signaling. See Figure 15 in the “Typical
Performance Curves” on page 14 for USB Full-speed
Eye Pattern taken with switch in the signal path.
The switches are active (turned ON) whenever the OE
voltage is logic “1” (High) and the LP voltage is logic
“X” (Don’t Care) and OFF when the OE voltage is logic
“0” (Low) and the LP voltage is logic “X” (Don’t Care).
When the OE voltage is logic “0” (Low) and the LP
voltage is logic “1” (High) the part goes into low power
mode.
OVERVOLTAGE PROTECTION (OVP)
The maximum normal operating signal range for the Dx
switches is from 0V to 3.6V. For normal operation, the
signal voltage should not be allowed to exceed these
voltage levels or go below ground by more than -0.3V.
However, in the event that a positive voltage >3.8V
(typ) to 5.25V, such as the USB 5V VBUS voltage, gets
shorted to one or both of the COM+ and COM- pins or
a negative voltage < -0.45V (typ) to -5V gets shorted
to one or both of the COM pins, the ISL54228 has OVP
circuitry to detect the overvoltage condition and open
the SPST switches to prevent damage to the USB
down-stream transceiver connected at the signal pins
(D-, D+).
The OVP and power-off protection circuitry allows the
COM pins (COM-, COM+) to be driven up to 5.25V
while the VDD supply voltage is in the range of 0V to
5.25V. In this condition, the part draws < 100A of
ICOMx and IDD current and causes no stress to the IC.
In addition, the SPST switches are OFF and the fault
voltage is isolated from the other side of the switch.
External VDD Series Resistor to Limit IDD
Current During Negative OVP Condition
A 100Ω to 1kΩ resistor in series with the VDD pin (see
the system power supply rail during a negative OVP
fault event.
With a negative -5V fault voltage at both COM pins, the
different external resistor values for supply voltages of
5.25V, 3.6V, and 2.7V. Note: With a 500Ω resistor, the
current draw is limited to around 5mA. When the
negative fault voltage is removed, the IDD current will
return to it’s normal operation current of 25A to 45A.
The series resistor also provides improved ESD and
latch-up immunity. During an overvoltage transient
event (such as occurs during system level IEC 61000
ESD testing), substrate currents can be generated in
the IC that can trigger parasitic SCR structures to
turn ON, creating a low impedance path from the
VDD power supply to ground. This will result in a
significant amount of current flow in the IC, which
can potentially create a latch-up state or
permanently damage the IC. The external VDD
resistor limits the current during this over-stress
situation and has been found to prevent latch-up or
destructive damage for many overvoltage transient
events.
Under normal operation, the low microamp IDD
current of the IC produces an insignificant voltage
drop across the series resistor resulting in no impact
to switch operation or performance.
ISL54228 Operation
The following will discuss using the ISL54228 shown
POWER
The power supply connected at the VDD pin provides
the DC bias voltage required by the ISL54228 part for
proper operation. The ISL54228 can be operated with
a VDD voltage in the range of 2.7V to 5.25V.
For lowest power consumption you should use the
lowest VDD supply.
A 0.01F or 0.1F decoupling capacitor should be
connected from the VDD pin to ground to filter out
any power supply noise from entering the part. The
capacitor should be located as close to the VDD pin
as possible.
FIGURE 6. VDD SERIES RESISTOR TO LIMIT IDD
CURRENT DURING NEGATIVE OVP AND
FOR ENHANCED ESD AND LATCH-UP
IMMUNITY
FIGURE 7. NEGATIVE OVP IDD CURRENT vs
RESISTOR VALUE vs VSUPPLY
OE
D+
100Ω to 1kΩ
COM+
COM-
VSUPPLY
GND
C
PROTECTION
RESISTOR
OVP
LOGIC
D-
LP
IDD
VDD
-5V
FAULT
VOLTAGE
ALM
INT
LOW
TO
INDICATE
OVP
0
5
10
15
20
25
100 200 300 400 500 600 700 800 900 1k
RESISTOR (Ω)
I DD
(mA)
VCOM+ = VCOM- = -5V
2.7V
3.6V
5.25V
ISL54228
相关PDF资料 |
PDF描述 |
|---|---|
| VE-2WY-IV-F3 | CONVERTER MOD DC/DC 3.3V 99W |
| VE-2WY-IV-F2 | CONVERTER MOD DC/DC 3.3V 99W |
| ISL84051IBZ-T7A | IC MULTIPLEXER 8X1 16SOIC |
| ISL54233IRUZ-T7A | IC INTERFACE |
| DSPIC30F4011T-20E/ML | IC DSPIC MCU/DSP 48K 44QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL54230 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Octal Multiprotocol Switch |
| ISL54230_09 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Octal Multiprotocol Switch |
| ISL54230EVAL3Z | 功能描述:EVALUATION BOARD ISL54230 RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:PCI Express® (PCIe) 主要目的:接口，收发器，PCI Express 嵌入式:- 已用 IC / 零件:DS80PCI800 主要属性:- 次要属性:- 已供物品:板 |
| ISL54230IIZ-T | 功能描述:IC USB SWITCH DPDT OCTAL 36WLCSP RoHS:是 类别:集成电路 (IC) >> 接口 - 模拟开关，多路复用器，多路分解器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:36 系列:- 功能:多路复用器 电路:2 x 4:1 导通状态电阻:75 欧姆 电压电源:单/双电源 电压 - 电源，单路/双路(±):2 V ~ 12 V，±2 V ~ 6 V 电流 - 电源:- 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:20-SOIC（0.295"，7.50mm 宽） 供应商设备封装:20-SOIC W 包装:管件 |
| ISL54230IRTZ | 功能描述:IC SWITCH QUAD DPDT 32TQFN RoHS:是 类别:集成电路 (IC) >> 接口 - 模拟开关，多路复用器，多路分解器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:36 系列:- 功能:多路复用器 电路:2 x 4:1 导通状态电阻:75 欧姆 电压电源:单/双电源 电压 - 电源，单路/双路(±):2 V ~ 12 V，±2 V ~ 6 V 电流 - 电源:- 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:20-SOIC（0.295"，7.50mm 宽） 供应商设备封装:20-SOIC W 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。