- 您现在的位置：买卖IC网 > PDF目录19712 > ISL6115CB-T (Intersil)IC CTRLR POWER DISTRIB 8-SOIC PDF资料下载
参数资料
| 型号： | ISL6115CB-T |
| 厂商： | Intersil |
| 文件页数： | 5/13页 |
| 文件大小： | 0K |
| 描述： | IC CTRLR POWER DISTRIB 8-SOIC |
| 标准包装： | 2,500 |
| 类型： | 热交换控制器 |
| 应用： | 通用 |
| 内部开关： | 无 |
| 电源电压： | 10.2 V ~ 13.8 V |
| 工作温度： | 0°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOICN |
| 包装： | 带卷 (TR) |
ISL6115, ISL6116, ISL6117, ISL6120
Electrical Specifications
V DD = 12V, T A = T J = 0°C to +85°C, Unless Otherwise Specified. Temperature limits
established by characterization and are not production tested. Boldface limits apply over the
operating temperature range, -40°C to +85°C. (Continued)
MIN
MAX
PARAMETER
SYMBOL
TEST CONDITIONS
(Note 7)
TYP
(Note 7) UNITS
PWRON Pull-Up Voltage
PWRON Rising Threshold
PWRON Hysteresis
PWRON Pull-Up Current
PWRN_V
PWR_Vth
PWR_hys
PWRN_I
PWRON Pin Open
2.7
1.4
130
9
3.2
1.7
170
17
-
2.0
250
25
V
V
mV
μA
CURRENT REGULATION DURATION/POWER GOOD
C TIM Charging Current
C TIM Fault Pull-Up Current (Note 6)
Current Limit Time-Out Threshold
Voltage
Power Good Pull Down Current
C TIM _ichg0
C TIM _Vth
PG_Ipd
V CTIM = 0V
CTIM Voltage
V OUT = 0.5V
16
-
1.3
-
20
20
1.8
8
23
-
2.3
-
μA
mA
V
mA
NOTES:
6. Limits established by characterization and are not production tested.
7. Parameters with MIN and/or MAX limits are 100% tested at +25°C, unless otherwise specified.
Description and Operation
The members of this IC family are single power supply
distribution controllers for generic hot swap
applications across the +2.5V to +12V supply range.
The ISL6115 is targeted for +12V switching
applications whereas the ISL6116 is targeted for +5V,
the ISL6117 for +3.3V and the ISL6120 for +2.5V
applications. Each IC has a hardwired undervoltage
(UV) threshold level approximately 17% lower than the
stated voltages.
These ICs feature a highly accurate programmable
current regulation (CR) level with programmable time
delay to latch-off, and programmable soft-start
turnHon ramp all set with a minimum of external
passive components. The ICs also include severe OC
protection that immediately shuts down the MOSFET
switch should a rapid load current transient such as
with a dead short cause the CR Vth to exceed the
programmed level by 150mV. Additionally, the ICs
have a UV indicator and an OC latch indicator. The
functionality of the PGOOD feature is enabled once
the IC is biased, monitoring and reporting any UV
condition on the ISEN pin.
Upon initial power-up, the IC can either isolate the
voltage supply from the load by holding the external
N-Channel MOSFET switch off or apply the supply rail
voltage directly to the load for true hot swap capability.
The PWRON pin must be pulled low for the device to
isolate the power supply from the load by holding the
external N-Channel MOSFET off. With the PWRON pin
held high or floating the IC will be in true hot swap
mode. In both cases the IC turns on in a soft-start
mode protecting the supply rail from sudden in-rush
current.
5
At turn-on, the external gate capacitor of the N-
Channel MOSFET is charged with a 10μA current
source resulting in a programmable ramp (soft-start
turn-on). The internal ISL6115 charge pump supplies
the gate drive for the 12V supply switch driving that
gate to ~V DD +5V, for the other three ICs the gate
drive voltage is limited to the chip bias voltage, VDD.
Load current passes through the external current
sense resistor. When the voltage across the sense
resistor exceeds the user programmed CR voltage
threshold value, (see Table 1 for R ISET programming
resistor value and resulting nominal current
regulation threshold voltage, V CR ) the controller
enters its current regulation mode. At this time, the
time-out capacitor, on CTIM pin is charged with a
20μA current source and the controller enters the
current limit time to latch-off period. The length of the
current limit time to latch-off duration is set by the
value of a single external capacitor (see Table 2) for
C TIM capacitor value and resulting nominal current
limited time-out to latch-off duration placed from the
CTIM pin (pin 6) to ground. The programmed current
level is held until either the OC event passes or the
time-out period expires. If the former is the case then
the N-Channel MOSFET is fully enhanced and the C TIM
capacitor is discharged. Once C TIM charges to 1.87V
signaling that the time-out period has expired, an
internal latch is set whereby the FET gate is quickly
pulled to 0V turning off the N-Channel MOSFET
switch, isolating the faulty load.
FN9100.7
April 29, 2010
相关PDF资料 |
PDF描述 |
|---|---|
| VE-B4P-CY-F3 | CONVERTER MOD DC/DC 13.8V 50W |
| ISPLSI 2128A-80LTN176I | IC PLD ISP 128I/O 15NS 176TQFP |
| EEM06DRTH | CONN EDGECARD 12POS DIP .156 SLD |
| VE-B4P-CY-F4 | CONVERTER MOD DC/DC 13.8V 50W |
| 182-037-213R171 | CONN DB37 FEMAL .318" R/A NICKEL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6115CBZA | 功能描述:IC CTRLR POWER DISTRIB 8-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:119 系列:- 类型:热交换控制器 应用:通用型，PCI Express? 内部开关:无 电流限制:- 电源电压:3.3V，12V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:80-TQFP 供应商设备封装:80-TQFP（12x12） 包装:托盘 产品目录页面:1423 (CN2011-ZH PDF) |
| ISL6115CBZA-T | 功能描述:IC CTRLR POWER DISTRIB 8-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:100 系列:- 类型:热插拔开关 应用:通用 内部开关:是 电流限制:可调 电源电压:9 V ~ 13.2 V 工作温度:-40°C ~ 150°C 安装类型:表面贴装 封装/外壳:10-WFDFN 裸露焊盘 供应商设备封装:10-TDFN-EP（3x3） 包装:管件 |
| ISL6115CBZA-TS2490 | 制造商:Intersil Corporation 功能描述:IBM, ISL6115CBZA-T W/CONTAINER LABELING - Tape and Reel 制造商:Intersil 功能描述:IBM, ISL6115CBZA-T W/CONTAINER LABELING |
| ISL6115CBZA-TS2490S | 制造商:Intersil Corporation 功能描述: |
| ISL6115EVAL1 | 功能描述:EVALUATION BOARD 12V ISL6115 RoHS:否 类别:编程器，开发系统 >> 过时/停产零件编号 系列:- 标准包装:1 系列:- 传感器类型:CMOS 成像，彩色（RGB） 传感范围:WVGA 接口:I²C 灵敏度:60 fps 电源电压:5.7 V ~ 6.3 V 嵌入式:否 已供物品:成像器板 已用 IC / 零件:KAC-00401 相关产品:4H2099-ND - SENSOR IMAGE WVGA COLOR 48-PQFP4H2094-ND - SENSOR IMAGE WVGA MONO 48-PQFP |
发布紧急采购，3分钟左右您将得到回复。