- 您现在的位置：买卖IC网 > PDF目录19710 > ISL6142IB (Intersil)IC CTRLR HOT PLUG NEG 14-SOIC PDF资料下载
参数资料
| 型号： | ISL6142IB |
| 厂商： | Intersil |
| 文件页数： | 20/23页 |
| 文件大小： | 0K |
| 描述： | IC CTRLR HOT PLUG NEG 14-SOIC |
| 标准包装： | 50 |
| 类型： | 热交换控制器 |
| 应用： | 通用型 VoIP |
| 内部开关： | 无 |
| 电源电压： | 36 V ~ 72 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 14-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 14-SOICN |
| 包装： | 管件 |
ISL6142, ISL6152
When any of the 5 conditions occur that turn off the GATE, the
Q3 DMOS turns off, and the resistor and Q2 clamp the
PWRGD pin to one diode drop (~0.7V) above the DRAIN pin.
This should be able to pull low against the module pull-up
current, and disable the module.
The input capacitance of the brick is chosen to match its
system requirements, such as filtering noise, and
maintaining regulation under varying loads. Note that this
input capacitance appears as the load capacitance of the
ISL6142, ISL6152.
-
Δ V GATE
V GH
GATE
V PG
+
-
V EE
V DH
+
-
VDD
(SECTION OF) ISL6152
(H VERSION)
6.2k
+
+ Q2
- LATCH Q3
LOGIC
V EE
+
-
PWRGD
+
CL
VIN+ VOUT+
ON/OFF
ACTIVE HIGH
ENABLE
MODULE
VIN- VOUT-
The brick’s output capacitance is also determined by the
system, including load regulation considerations. However, it
can affect the ISL6142, ISL6152, depending upon how it is
enabled. For example, if the PWRGD/PWRGD signal is not
used to enable the brick, the following could occur.
Sometime during the inrush current time, as the main power
supply starts charging the brick input capacitors, the brick
itself will start working, and start charging its output
capacitors and load; that current has to be added to the
inrush current. In some cases, the sum could exceed the
Over-Current threshold, which could shut down the system if
the time-out period is exceeded! Therefore, whenever
V EE
DRAIN
FIGURE 37. ACTIVE HIGH ENABLE MODULE
Applications: GATE Pin
To help protect the external FET, the output of the GATE pin
is internally clamped; up to an 80V supply and will not be any
higher than 15V. Under normal operation when the supply
voltage is above 20V, the GATE voltage will be regulated to a
nominal 13.6V above V EE .
Applications: “Brick” Regulators
One of the typical loads used are DC/DC regulators, some
commonly known as “brick” regulators, (partly due to their
shape, and because it can be considered a “building block” of
a system). For a given input voltage range, there are usually
whole families of different output voltages and current
ranges. There are also various standardized sizes and
pinouts, starting with the original “full” brick, and since getting
smaller (half-bricks and quarter-bricks are now common).
Other common features may include: all components
(except some filter capacitors) are self-contained in a
molded plastic package; external pins for connections; and
often an ENABLE input pin to turn it on or off. A hot plug IC,
such as the ISL6142 is often used to gate power to a brick,
as well as turn it on.
Many bricks have both logic polarities available (Enable high
or low input); select the ISL6142 (L-version) or ISL6152
(H-version) to match. There is little difference between them,
although the L-version output is usually simpler to interface.
The Enable input often has a pull-up resistor or current
source, or equivalent built in; care must be taken in the
ISL6152 (H version) output that the given current will create
a high enough input voltage (remember that current through
the RPG 6.2k ? resistor generates the high voltage level;
(see Figure 34).
20
practical, it is advantageous to use the PWRGD/PWRGD
output to keep the brick off at least until the input caps are
charged up, and then start-up the brick to charge its output
caps.
Typical brick regulators include models such as Lucent
JW050A1-E or Vicor VI-J30-CY. These are nominal -48V
input, and 5V outputs, with some isolation between the input
and output.
Applications: Optional Components
In addition to the typical application, and the variations
already mentioned, there are a few other possible
components that might be used in specific cases. See
Figure 38 for some possibilities.
If the input power supply exceeds the 100V absolute
maximum rating, even for a short transient, that could cause
permanent damage to the IC, as well as other components
on the board. If this cannot be guaranteed, a voltage
suppressor (such as the SMAT70A, D1) is recommended.
When placed from V DD to -V IN on the board, it will clamp the
voltage.
If transients on the input power supply occur when the
supply is near either the OV or UV trip points, the GATE
could turn on or off momentarily. One possible solution is to
add a filter cap C4 to the V DD pin, through isolation resistor
R11. A large value of R11 is better for the filtering, but be
aware of the voltage drop across it. For example, a 1k ?
resistor, with 2.4mA of I DD would have 2.4V across it and
dissipate 2.4mW. Since the UV and OV comparators are
referenced with respect to V EE, they should not be affected ,
but the GATE clamp voltage could be offset by the voltage
across the extra resistor.
The switch SW1 is shown as a simple push button. It can be
replaced by an active switch, such as an NPN or NFET; the
principle is the same; pull the UV node below its trip point,
and then release it (toggle low). To connect an NFET, for
相关PDF资料 |
PDF描述 |
|---|---|
| MIC3975-5.0BMM | IC REG LDO 5V .75A 8-MSOP |
| ISL6141IB-T | IC CTRLR HOT PLUG NEG VOLT 8SOIC |
| AMM15DTAN | CONN EDGECARD 30POS R/A .156 SLD |
| LC5512MV-45F484C | IC XPLD 512MC 4.5NS 484FPBGA |
| 180-015-202L011 | CONN DB15 FEMALE HD SLD CUP TIN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6142IB-T | 功能描述:IC CTRLR HOT PLUG NEG 14-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:100 系列:- 类型:热插拔开关 应用:通用 内部开关:是 电流限制:可调 电源电压:9 V ~ 13.2 V 工作温度:-40°C ~ 150°C 安装类型:表面贴装 封装/外壳:10-WFDFN 裸露焊盘 供应商设备封装:10-TDFN-EP（3x3） 包装:管件 |
| ISL6142IBZA | 功能描述:IC CTRLR HOT PLUG NEG 14-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:100 系列:- 类型:热插拔开关 应用:通用 内部开关:是 电流限制:可调 电源电压:9 V ~ 13.2 V 工作温度:-40°C ~ 150°C 安装类型:表面贴装 封装/外壳:10-WFDFN 裸露焊盘 供应商设备封装:10-TDFN-EP（3x3） 包装:管件 |
| ISL6142IBZA-T | 功能描述:IC CTRLR HOT PLUG NEG 14-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:100 系列:- 类型:热插拔开关 应用:通用 内部开关:是 电流限制:可调 电源电压:9 V ~ 13.2 V 工作温度:-40°C ~ 150°C 安装类型:表面贴装 封装/外壳:10-WFDFN 裸露焊盘 供应商设备封装:10-TDFN-EP（3x3） 包装:管件 |
| ISL6144 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:High Voltage ORing MOSFET Controller |
| ISL6144_07 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:High Voltage ORing MOSFET Controller |
发布紧急采购，3分钟左右您将得到回复。