- 您现在的位置：买卖IC网 > PDF目录383141 > ISL6161CB-T (INTERSIL CORP) Dual Power Distribution Controller PDF资料下载
参数资料
| 型号： | ISL6161CB-T |
| 厂商： | INTERSIL CORP |
| 元件分类： | 电源管理 |
| 英文描述： | Dual Power Distribution Controller |
| 中文描述： | 2-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO14 |
| 封装： | PLASTIC, MS-012AB, SOIC-14 |
| 文件页数： | 3/10页 |
| 文件大小： | 224K |
| 代理商： | ISL6161CB-T |
3
Pin Descriptions
PIN #
SYMBOL
FUNCTION
DESCRIPTION
1
12VS
12V Source
Connect to source of associated external N-Channel MOSFET switch to sense output
voltage.
2
12VG
12V Gate
Connect to the gate of associated N-Channel MOSFET switch. A capacitor from this node
to ground sets the turn-on ramp. At turn-on this capacitor will be charged to ~17.4V by a
10
μ
A current source.
3
V
DD
Chip Supply
Connect to 12V supply. This can be either connected directly to the +12V rail supplying the
load voltage or to a dedicated V
DD
+12V supply. If the former is chosen special attention to
V
DD
decoupling must be paid to prevent sagging as heavy loads are switched on.
4
NC
Not Connected
5
ENABLE
Enable / Reset
ENABLE is used to turn-on and reset the chip. Both outputs turn-on when this pin is driven
low. After a current limit time out, the chip is reset by the rising edge of a reset signal applied
to the ENABLE pin. This input has 100
μ
A pull up capability which is compatible with 3V and
5V open drain and standard logic.
6
3VG
3V Gate
Connect to the gate of the external 3V N-Channel MOSFET. A capacitor from this node to
ground sets the turn-on ramp. At turn-on this capacitor will be charged to ~11.4V by a 10
μ
A
current source.
7
3VS
3 Source
Connect to the source side of 3V external N-Channel MOSFET switch to sense output
voltage.
8
3VISEN
3V Current Sense
Connect to the load side of the 3V sense resistor to measure the voltage drop across this
resistor between 3VS and 3VISEN pins.
9
PGOOD
Power Good indicator
Indicates that all output voltages are within specification. PGOOD is driven by an open drain
N-Channel MOSFET. It is pulled low when any output is not within specification.
10
C
TIM
Current Limit Timing
Capacitor
Connect a capacitor from this pin to ground. This capacitor controls the time between the
onset of current limit and chip shutdown (current limit time-out). The duration of current limit
time-out (in seconds) = 200k
x C
TIM
(Farads).
11
C
PUMP
Charge Pump
Capacitor
Connect a 0.1
μ
F capacitor between this pin and V
DD
(pin 3). Provides charge storage for
12VG drive.
12
GND
Chip Ground
13
R
ILIM
Current Limit Set
Resistor
A resistor connected between this pin and ground determines the current level at which
current limit is activated. This current is determined by the ratio of the R
ILIM
resistor to the
sense resistor (R
SENSE
). The current at current limit onset is equal to 10
μ
A x (R
ILIM
/
R
SENSE
). The ISL6161 is limited to a 10k
min. value (OC Vth = 100mV) resistor whereas
the ISL6161 can accommodate a 5k
resistor for a lower OC Vth (50mV).
14
12VISEN
12V Current Sense
Connect to the load side of sense resistor to measure the voltage drop across this resistor.
ISL6161
相关PDF资料 |
PDF描述 |
|---|---|
| ISL6161 | Octal D-Type Transparent Latches With 3-State Outputs 20-SO -40 to 85 |
| ISL6161CB | Dual Power Distribution Controller |
| ISL6161CBZA | Octal D-Type Transparent Latches With 3-State Outputs 20-TSSOP -40 to 85 |
| ISL6161CBZA-T | Octal D-Type Transparent Latches With 3-State Outputs 20-TSSOP -40 to 85 |
| ISL6173DRZA | Dual Low Voltage Hot Swap Controller |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6161CBZA | 功能描述:IC CTLR PWR DISTRIB DUAL 14SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:119 系列:- 类型:热交换控制器 应用:通用型，PCI Express? 内部开关:无 电流限制:- 电源电压:3.3V，12V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:80-TQFP 供应商设备封装:80-TQFP（12x12） 包装:托盘 产品目录页面:1423 (CN2011-ZH PDF) |
| ISL6161CBZA-T | 功能描述:IC CTLR PWR DISTRIB DUAL 14SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:119 系列:- 类型:热交换控制器 应用:通用型，PCI Express? 内部开关:无 电流限制:- 电源电压:3.3V，12V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:80-TQFP 供应商设备封装:80-TQFP（12x12） 包装:托盘 产品目录页面:1423 (CN2011-ZH PDF) |
| ISL6161IBZA | 功能描述:IC CTRLR PWR DISTRIB DUAL 14SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:100 系列:- 类型:热插拔开关 应用:通用 内部开关:是 电流限制:可调 电源电压:9 V ~ 13.2 V 工作温度:-40°C ~ 150°C 安装类型:表面贴装 封装/外壳:10-WFDFN 裸露焊盘 供应商设备封装:10-TDFN-EP（3x3） 包装:管件 |
| ISL6161IBZA-T | 功能描述:IC CTRLR PWR DISTRIB DUAL 14SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:100 系列:- 类型:热插拔开关 应用:通用 内部开关:是 电流限制:可调 电源电压:9 V ~ 13.2 V 工作温度:-40°C ~ 150°C 安装类型:表面贴装 封装/外壳:10-WFDFN 裸露焊盘 供应商设备封装:10-TDFN-EP（3x3） 包装:管件 |
| ISL6172DRZA | 功能描述:热插拔功率分布 W/ANNEAL DL LV HOT SWAP CNTRLR 0-85 TMP RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。