- 您现在的位置：买卖IC网 > PDF目录383141 > ISL6173 (Intersil Corporation) Dual Low Voltage Hot Swap Controller PDF资料下载
参数资料
| 型号： | ISL6173 |
| 厂商： | Intersil Corporation |
| 元件分类： | 基准电压源/电流源 |
| 英文描述： | Dual Low Voltage Hot Swap Controller |
| 中文描述： | 双低电压热插拔控制器 |
| 文件页数： | 11/20页 |
| 文件大小： | 452K |
| 代理商： | ISL6173 |
11
FN9186.2
February 15, 2005
The two channels can be forced to track each other by
simply tying their SS pins together and using a common SS
capacitor. In addition, their EN pins also must be tied
together. Typical Start-up waveforms in this mode are shown
in Figure 15. If one channel goes down for any reason, the
other one will too. One important thing to note here is that
only the overcurrent latch-off mode will work. Auto-retry
feature WILL NOT work. Retry must be controlled manually
through EN.
Typical Hot-plug Power Up Sequence
1. When power is applied to the IC on the BIAS pin, the first
charge pump immediately powers up.
2. If the BIAS voltage is 2.1V or higher, the IC comes out of
POR. Both SS and CT caps remain discharged and the
gate (GT) voltage remains low.
3. ENx pin, when pulled low (below it’s specified threshold),
enables the respective channel.
4. SSx cap begins to charge up through the internal 10μA
current source, the gate (GT) voltage begins to rise and
the corresponding output voltage begins to rise at the
same rate as the SS cap voltage. This is tightly controlled
by the soft-start amplifier shown in the block diagram.
5. SS cap begins to charge but the corresponding CTx cap
is held discharged.
6. Fault (FLT) remains deasserted (stays high) and the
output voltage continues to rise.
7. If the load current on the output exceeds the set current
limit for greater than the OC timeout period, FLT gets
asserted and the channel shutdown occurs.
8. If the voltage on UV pin exceeds 633mV threshold as a
result of rising Vo, the Power Good (PG) output goes
active.
9. At the end of the SS interval, the SS cap voltage reaches
CPVDD and remains charged as long as EN remains
asserted or there is no other fault condition present that
would attempt to pull down the gate.
State Diagram
This is shown in Figure 16. It provides a quick overview of
the IC operation and can also be used as a troubleshooting
road map.
ISL6173
相关PDF资料 |
PDF描述 |
|---|---|
| ISL6173EVAL3 | Dual Low Voltage Hot Swap Controller |
| ISL6173DRZA-T | Dual Low Voltage Hot Swap Controller |
| ISL6206CB | High Voltage Synchronous Rectified Buck MOSFET Driver |
| ISL6206 | Octal D-Type Transparent Latches With 3-State Outputs 20-TSSOP -40 to 85 |
| ISL6206CB-T | High Voltage Synchronous Rectified Buck MOSFET Driver |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6173_06 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Dual Low Voltage Hot Swap Controller |
| ISL6173DRZA | 功能描述:IC CTRLR HOT SWAP DUAL LV 28QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 标准包装:50 系列:- 类型:热交换控制器 应用:-48V 远程电力系统，AdvancedTCA ? 系统，高可用性 内部开关:无 电流限制:可调 电源电压:11.5 V ~ 14.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-MSOP 包装:管件 |
| ISL6173DRZA-T | 功能描述:IC CTRLR HOT SWAP DUAL LV 28-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:100 系列:- 类型:热插拔开关 应用:通用 内部开关:是 电流限制:可调 电源电压:9 V ~ 13.2 V 工作温度:-40°C ~ 150°C 安装类型:表面贴装 封装/外壳:10-WFDFN 裸露焊盘 供应商设备封装:10-TDFN-EP（3x3） 包装:管件 |
| ISL6173EVAL1 | 功能描述:EVALUATION BOARD FOR ISL6173 RoHS:否 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:PCI Express® (PCIe) 主要目的:接口，收发器，PCI Express 嵌入式:- 已用 IC / 零件:DS80PCI800 主要属性:- 次要属性:- 已供物品:板 |
| ISL6173EVAL3 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Dual Low Voltage Hot Swap Controller |
发布紧急采购，3分钟左右您将得到回复。