- 您现在的位置：买卖IC网 > PDF目录16625 > ISL6218CRZ (Intersil)IC CTRLR IMPVP-IV SGL-PHS 40-QFN PDF资料下载
参数资料
| 型号： | ISL6218CRZ |
| 厂商： | Intersil |
| 文件页数： | 8/19页 |
| 文件大小： | 0K |
| 描述： | IC CTRLR IMPVP-IV SGL-PHS 40-QFN |
| 标准包装： | 50 |
| 应用： | 处理器 |
| 电流 - 电源： | 1.4mA |
| 电源电压： | 4.75 V ~ 5.25 V |
| 工作温度： | -10°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 40-VFQFN 裸露焊盘 |
| 供应商设备封装： | 40-QFN 裸露焊盘（6x6） |
| 包装： | 管件 |
ISL6218
VID
VR_ON/EN
<3ms
CAPTURE VID CODE
V CC-CORE
-12%
t1
>10μs
t2
V BOOT
V VID
PGOOD VCCP/VCC-MCH
3ms TO 12ms
PGOOD VCC-CORE
FIGURE 2. TIMING DIAGRAM SHOWING VR_ON, VCC_CORE AND PGOOD FOR VCC_CORE, VCCP AND VCC_MCH
Theory of Operation
Initialization
Once the +5VDC supply voltage (as connected to the
ISL6218 VDD pin) reaches the Power-On Reset (POR)
rising threshold, the PWM drive signals are held in
“Three-State” or high impedance mode. This results in both
the high side and low side MOSFETs being held off. Once
the supply voltage exceeds the POR rising threshold, the
controller will respond to a logic level high on the EN pin and
initiate the soft-start interval. If the supply voltage drops
below the POR falling threshold, POR shutdown is triggered
and the PWM outputs are again driven to “Three-State”.
The system signal, VR_ON is directly connected to the EN
pin of the ISL6218. Once the voltage on the EN pin rises
above 2.0V, the chip is enabled and soft-start begins. The
EN pin of the ISL6218 is also used to reset the ISL6218 for
cases when an undervoltage or overcurrent fault condition
has latched the IC off. Toggling the state of this pin to a level
below 1.0V will re-enable the IC. For the case of an
overvoltage fault, the VDD pin must be reset.
During start-up, the ISL6218 regulates to the voltage on the
STV pin. This is referred to as the “Boot” voltage and is
labeled VBOOT in Figure 2. Once power good signals are
received from the Vccp and Vcc_mch regulators, the
ISL6218 will capture the VID code and regulate, within 3ms
to 12ms, to this command voltage. The PGOOD pin of the
ISL6218 is both an input and an output and is further
8
Soft-Start Interval
Refer to Figure 2 and Figure 4. Once VDD rises above the
POR rising threshold and the EN pin voltage is above the
threshold of 2.0V, a soft-start interval is initiated. The voltage
on the EA+ pin is the reference voltage for the regulator. The
voltage on the EA+ pin is equal to the voltage on the SOFT
pin minus the “Droop” resistor voltage, V DROOP . During
start-up, when the voltage on SOFT is less than the “Boot”
voltage V BOOT , a 130μA current source I1, is used to slowly
ramp up the voltage on the soft-start capacitor C SOFT . This
slowly ramps up the reference voltage for the controller, and
controls the slew rate of the output voltage. The STV pin is
externally programmable and sets the start-up or “Boot”
voltage V BOOT . The programming of this voltage level is
The ISL6218 PGOOD pin is both an input and an output.
The system signal IMVP4_PWRGD is connected to power
good signals from the Vccp and Vcc_mch supplies. The
Intersil ISL6225 Dual Voltage Regulator is an ideal choice for
the Vccp and Vcc_mch supplies.
Refer to Figure 2 and Figure 4. Once the output voltage is
within the “Boot” level regulation limits and a logic high
PGOOD signal from the Vccp and Vccp_mch regulators is
received, the ISL6218 is enabled to capture the VID code
and regulate to that command voltage.
The “Droop” current source I DROOP , is proportional to load
current. This current source is used to reduce the reference
voltage on EA+ by the voltage drop across the “Droop”
resistor. A more in-depth explanation of “Droop” and the
sizing of this resistor can be found in “Droop Compensation”
FN9101.6
August 6, 2007
相关PDF资料 |
PDF描述 |
|---|---|
| GBA28DTAD | CONN EDGECARD 56POS R/A .125 SLD |
| VI-B7J-EX | CONVERTER MOD DC/DC 36V 75W |
| ISL6218CVZ-T | IC CTRLR INTEL PENT M 38-TSSOP |
| ELC-18B220L | COIL CHOKE 22UH RADIAL |
| ELC-18B180L | COIL CHOKE 18UH RADIAL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6218CRZ-T | 功能描述:电流型 PWM 控制器 P6 MULTIPHS BUCK PWM CNTRLR FOR IMVP4 RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| ISL6218CV | 功能描述:IC CTRLR INTEL PENT M 38-TSSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 电源管理 - 专用 系列:- 应用说明:Ultrasound Imaging Systems Application Note 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:37 系列:- 应用:医疗用超声波成像，声纳 电流 - 电源:- 电源电压:2.37 V ~ 6 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:56-WFQFN 裸露焊盘 供应商设备封装:56-TQFN-EP（8x8） 包装:管件 |
| ISL6218CV-T | 功能描述:IC CTRLR INTEL PENT M 38-TSSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 电源管理 - 专用 系列:- 应用说明:Ultrasound Imaging Systems Application Note 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:37 系列:- 应用:医疗用超声波成像，声纳 电流 - 电源:- 电源电压:2.37 V ~ 6 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:56-WFQFN 裸露焊盘 供应商设备封装:56-TQFN-EP（8x8） 包装:管件 |
| ISL6218CVZ | 功能描述:电流型 PWM 控制器 P6 MULTIPHS BUCK PWM CNTRLR FOR IMVP4 IBM RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| ISL6218CVZA | 功能描述:电流型 PWM 控制器 W/ANNEAL P6 MULTIPHS BUCK PWM CONTR RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
发布紧急采购，3分钟左右您将得到回复。