- 您现在的位置：买卖IC网 > PDF目录17311 > ISL6228EVAL3Z (Intersil)EVALUATION BOARD FOR ISL6228 PDF资料下载
参数资料
| 型号： | ISL6228EVAL3Z |
| 厂商： | Intersil |
| 文件页数： | 13/16页 |
| 文件大小： | 0K |
| 描述： | EVALUATION BOARD FOR ISL6228 |
| 标准包装： | 1 |
| 系列： | Robust Ripple Regulator™ (R³) |
| 主要目的： | DC/DC，步降 |
| 输出及类型： | 2，非隔离 |
| 输出电压： | 1.5V 或 1.8V，1.8V |
| 电流 - 输出： | 8A，8A |
| 输入电压： | 3.3 ~ 25 V |
| 稳压器拓扑结构： | 降压 |
| 频率 - 开关： | 270kHz，300kHz |
| 板类型： | 完全填充 |
| 已供物品： | 板 |
| 已用 IC / 零件： | ISL6228 |
ISL6228
As an example, suppose the high-side MOSFET has a total
gate charge Q g , of 25nC at V GS = 5V, and a Δ V BOOT of
200mV. The calculated bootstrap capacitance is 0.125μF; for
a comfortable margin, select a capacitor that is double the
calculated capacitance. In this example, 0.22μF will suffice.
Use an X7R or X5R ceramic capacitor.
Layout Considerations
As a general rule, power should be on the bottom layer of
the PCB and weak analog or logic signals are on the top
layer of the PCB. The ground-plane layer should be adjacent
to the top layer to provide shielding. The ground plane layer
should have an island located under the IC, the
compensation components, and the FSET components. The
island should be connected to the rest of the ground plane
layer at one point.
EN (Pins 11 and 24), and PGOOD (Pins 7 and 28)
These are logic signals that are referenced to the GND pin.
Treat as a typical logic signal.
OCSET (Pins 10 and 25)
The current-sensing network consisting of R OCSET and
C SEN needs to be connected to the inductor pads for
accurate measurement. Connect R OCSET to the phase-
node side pad of the inductor, and connect C SEN to the
output side pad of the inductor. Connect the OCSET pin to
the common node of node of R OCSET and C SEN .
FB (Pins 8 and 27), and VO (Pins 9 and 26)
The VO pin is used to sense the inductor current for OCP.
Connect the VO pin to the output-side of C SEN through
resistor R O . The input impedance of the FB pin is high, so
place the voltage programming and loop compensation
VIAS TO
GROUND
PLANE
INDUCTOR
HIGH-SIDE
MOSFETS
GND
VOUT
PHASE
NODE
VIN
OUTPUT
CAPACITORS
SCHOTTKY
DIODE
LOW-SIDE
MOSFETS
INPUT
CAPACITORS
components close to the VO, FB, and GND pins keeping the
high impedance trace short.
FSET (Pins 1 and 6)
This pin requires a quiet environment. The resistor R FSET
and capacitor C FSET should be placed directly adjacent to
this pin. Keep fast moving nodes away from this pin.
LGATE (Pins 16 and 19)
The signal going through this trace is both high dv/dt and
FIGURE 8. TYPICAL POWER COMPONENT PLACEMENT
Signal Ground and Power Ground
The bottom of the ISL6228 TQFN package is the signal
ground (GND) terminal for analog and logic signals of the IC.
Connect the GND pad of the ISL6228 to the island of ground
plane under the top layer using several vias, for a robust
thermal and electrical conduction path. Connect the input
capacitors, the output capacitors, and the source of the
lower MOSFETs to the power ground plane.
PGND (Pins 17 and 18)
This is the return path for the pull-down of the LGATE
low-side MOSFET gate driver. Ideally, PGND should be
connected to the source of the low-side MOSFET with a
low-resistance, low-inductance path.
VIN (Pins 2 and 5)
The VIN pin should be connected close to the drain of the
high-side MOSFET, using a low resistance and low
inductance path.
VCC (Pins 3 and 4)
For best performance, place the decoupling capacitor very
close to the VCC and GND pins.
PVCC (Pins 15 and 20)
For best performance, place the decoupling capacitor very
close to the PVCC and respective PGND pins, preferably on
the same side of the PCB as the ISL6228 IC.
13
high di/dt, with high peak charging and discharging current.
Route this trace in parallel with the trace from the PGND pin.
These two traces should be short, wide, and away from
other traces. There should be no other weak signal traces in
proximity with these traces on any layer.
BOOT (Pins 14 and 21), UGATE (Pins 13 and 22), and
PHASE (Pins 12 and 23)
The signals going through these traces are both high dv/dt
and high di/dt, with high peak charging and discharging
current. Route the UGATE and PHASE pins in parallel with
short and wide traces. There should be no other weak signal
traces in proximity with these traces on any layer.
Copper Size for the Phase Node
The parasitic capacitance and parasitic inductance of the
phase node should be kept very low to minimize ringing. It is
best to limit the size of the PHASE node copper in strict
accordance with the current and thermal management of the
application. An MLCC should be connected directly across
the drain of the upper MOSFET and the source of the lower
MOSFET to suppress the turn-off voltage spike.
FN9095.2
May 7, 2008
相关PDF资料 |
PDF描述 |
|---|---|
| ASPI-0602S-3R0M-T | INDUCTOR POWER 3.0UH 0602 SMD |
| HKQ0603S2N9C-T | INDUCTOR HI FREQ 2.9NH 0201 |
| A9CCA-1803F | FLEX CABLE - AFG18A/AF18/AFG18A |
| A9BBA-2506E | FLEX CABLE - AFJ25A/AE25/AFJ25A |
| A9CCG-1804F | FLEX CABLE - AFG18G/AF18/AFG18G |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6228HIEVAL3Z | 功能描述:EVALUATION BOARD FOR ISL6228HI RoHS:是 类别:编程器，开发系统 >> 评估板 - DC/DC 与 AC/DC（离线）SMPS 系列:Robust Ripple Regulator™ (R³) 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:True Shutdown™ 主要目的:DC/DC，步升 输出及类型:1，非隔离 功率 - 输出:- 输出电压:- 电流 - 输出:1A 输入电压:2.5 V ~ 5.5 V 稳压器拓扑结构:升压 频率 - 开关:3MHz 板类型:完全填充 已供物品:板 已用 IC / 零件:MAX8969 |
| ISL6228HRTZ | 功能描述:IC REG CTRLR BUCK PWM 28-TQFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:Robust Ripple Regulator™ (R³) 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:275kHz 占空比:50% 电源电压:18 V ~ 110 V 降压:无 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) |
| ISL6228HRTZ-T | 功能描述:电压模式 PWM 控制器 ISL6228 NOTEBOOK DL CNTRLR 4X4 TQFN T RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| ISL6228IRTZ | 功能描述:IC REG CTRLR BUCK PWM 28-TQFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:Robust Ripple Regulator™ (R³) 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:275kHz 占空比:50% 电源电压:18 V ~ 110 V 降压:无 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) |
| ISL6228IRTZ-T | 功能描述:IC REG CTRLR BUCK PWM 28-TQFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:Robust Ripple Regulator™ (R³) 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:275kHz 占空比:50% 电源电压:18 V ~ 110 V 降压:无 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。