- 您现在的位置：买卖IC网 > PDF目录15156 > ISL6327ACRZ (Intersil)IC REG CTRLR BUCK PWM 48-QFN PDF资料下载
参数资料
| 型号： | ISL6327ACRZ |
| 厂商： | Intersil |
| 文件页数： | 24/29页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM 48-QFN |
| 标准包装： | 43 |
| PWM 型： | 控制器 |
| 输出数： | 6 |
| 频率 - 最大： | 1MHz |
| 电源电压： | 4.75 V ~ 5.25 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | 0°C ~ 70°C |
| 封装/外壳： | 48-VFQFN 裸露焊盘 |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页当前第24页第25页第26页第27页第28页第29页
ISL6327A
At turn-on, the upper MOSFET begins to conduct and this
transition occurs over a time t 2 . In Equation 25, the
approximate power loss is P UP,2 .
temperature. R X in Equation 28 should be the maximum DC
resistance of the current sense element at all the operational
temperature.
P UP , 2 ≈ V IN ? ------ – ---------- ? ? ---- 2 ? f S
? I M I P-P ? ? t ?
? N 2 ? ? 2 ?
(EQ. 25)
In certain circumstances, it may be necessary to adjust the
value of one or more ISEN resistors. When the components
of one or more channels are inhibited from effectively
P UP , 3 = V IN Q rr f S
I P-P2
? I M ?
P UP , 4 ≈ r DS ( ON ) ? ------ ? d + ----------d
R ISEN , 2 = R ISEN ---------- 2
Δ T 1
A third component involves the lower MOSFET’s reverse
recovery charge, Q rr . Since the inductor current has fully
commutated to the upper MOSFET before the lower
MOSFET’s body diode can draw all of Q rr , it is conducted
through the upper MOSFET across VIN. The power
dissipated as a result is P UP,3 and is approximately.
(EQ. 26)
Finally, the resistive part of the upper MOSFET’s is given in
Equation 27 as P UP,4 .
2
(EQ. 27)
? N ? 12
The total power dissipated by the upper MOSFET at full load
can now be approximated as the summation of the results
from Equations 24, 25, 26 and 27. Since the power
equations depend on MOSFET parameters, choosing the
correct MOSFETs can be an iterative process involving
repetitive solutions to the loss equations for different
MOSFETs and different switching frequencies.
Current Sensing Resistor
dissipating their heat so that the affected channels run hotter
than desired, choose new, smaller values of RISEN for the
affected phases (see the section titled “Channel-Current
Balance” on page 12). Choose R ISEN,2 in proportion to the
desired decrease in temperature rise in order to cause
proportionally less current to flow in the hotter phase.
Δ T
(EQ. 29)
In Equation 29, make sure that Δ T 2 is the desired temperature
rise above the ambient temperature, and Δ T 1 is the measured
temperature rise above the ambient temperature. While a
single adjustment according to Equation 29 is usually
sufficient, it may occasionally be necessary to adjust R ISEN
two or more times to achieve optimal thermal balance
between all channels.
Load-Line Regulation Resistor
The load-line regulation resistor is labelled R FB in Figure 5.
Its value depends on the desired loadline requirement of the
application.
The desired loadline can be calculated using Equation 30:
R LL = -------------------------
The resistors connected to the Isen+ pins determine the
gains in the load-line regulation loop and the channel-current
V DROOP
I FL
(EQ. 30)
R ISEN = ----------------------- --------------
85 × 10
balance loop as well as setting the overcurrent trip point.
Select values for these resistors by the Equation 28.
R X I OCP (EQ. 28)
N
where R ISEN is the sense resistor connected to the ISEN+
where I FL is the full load current of the specific application,
and VR DROOP is the desired voltage droop under the full
load condition.
Based on the desired loadline R LL , the loadline regulation
resistor can be calculated using Equation 31:
NR R
R FB = ----------------------------------
pin, N is the active channel number, R X is the resistance of
the current sense element, either the DCR of the inductor or
R SENSE depending on the sensing method, and I OCP is the
ISEN LL
R X
(EQ. 31)
desired overcurrent trip point. Typically, I OCP can be chosen
to be 1.3x the maximum load current of the specific
application.
With integrated temperature compensation, the sensed
current signal is independent on the operational temperature
of the power stage, i.e. the temperature effect on the current
sense element R X is cancelled by the integrated
temperature compensation function. R X in Equation 28
where N is the active channel number, R ISEN is the sense
resistor connected to the ISEN+ pin, and R X is the
resistance of the current sense element, either the DCR of
the inductor or R SENSE depending on the sensing method.
If one or more of the current sense resistors are adjusted for
thermal balance, as in Equation 29, the load-line regulation
resistor should be selected based on the average value of
the current sensing resistors, as given in Equation 32:
R FB = ----------
should be the resistance of the current sense element at the
room temperature.
R LL
R X
∑ R ISEN ( n )
n
(EQ. 32)
When the integrated temperature compensation function is
disabled by pulling the TCOMP pin to GND, the sensed
current will be dependent on the operational temperature of
the power stage, since the DC resistance of the current
sense element may be changed according to the operational
24
where R ISEN(n) is the current sensing resistor connected to
the n th ISEN+ pin.
FN6833.0
February 17, 2009
相关PDF资料 |
PDF描述 |
|---|---|
| RBA40DRSD-S288 | CONN EDGECARD 80POS .125 EXTEND |
| ECM31DCAI | CONN EDGECARD 62POS R/A .156 SLD |
| ECM31DCBI | CONN EDGECARD 62POS R/A .156 SLD |
| GMM24DTKN-S288 | CONN EDGECARD 48POS .156 EXTEND |
| ECA31DCBS | CONN EDGECARD 62POS R/A .125 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6327ACRZ-T | 功能描述:IC REG CTRLR BUCK PWM 48-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:275kHz 占空比:50% 电源电压:18 V ~ 110 V 降压:无 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) |
| ISL6327AIRZ | 功能描述:IC REG CTRLR BUCK PWM 48-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:275kHz 占空比:50% 电源电压:18 V ~ 110 V 降压:无 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) |
| ISL6327AIRZ-T | 功能描述:IC REG CTRLR BUCK PWM 48-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:275kHz 占空比:50% 电源电压:18 V ~ 110 V 降压:无 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) |
| ISL6327CRZ | 功能描述:IC REG CTRLR BUCK PWM 48-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:275kHz 占空比:50% 电源电压:18 V ~ 110 V 降压:无 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) |
| ISL6327CRZ-T | 功能描述:IC REG CTRLR BUCK PWM 48-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:275kHz 占空比:50% 电源电压:18 V ~ 110 V 降压:无 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。