参数资料
| 型号： | ISL6328AIRZ-T |
| 厂商： | Intersil |
| 文件页数： | 21/33页 |
| 文件大小： | 0K |
| 描述： | IC VOLTAGE REGULATOR |
| 标准包装： | 4,000 |
| 系列： | * |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页当前第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页
ISL6328A
ramp from the pre-charged level to the final level dictated by the
DAC setting. Should the output be pre-charged to a level
exceeding the DAC setting, the output drives are enabled at the
end of the soft-start period, leading to an abrupt correction in the
output voltage down to the DAC-set level.
OUTPUT PRECHARGED
ABOVE DAC LEVEL
OUTPUT PRECHARGED
BELOW DAC LEVEL
V CORE
400mV/DIV
EN
5V/DIV
100μs/DIV
FIGURE 12. SOFT-START WAVEFORMS FOR ISL6328A-BASED
MULTIPHASE CONVERTER
At the inception of an overvoltage event, both on-board lower gate pins
are commanded low as are the active PWM outputs to the external
drivers, the PGOOD signal is driven low, and the ISL6328A latches off
normal PWM action. This turns on the all of the lower MOSFETs and
pulls the output voltage below a level that might cause damage to the
load. The lower MOSFETs remain driven ON until VSEN falls below
400mV. The ISL6328A will continue to protect the load in this fashion
as long as the overvoltage condition recurs. Once an overvoltage
condition ends the ISL6328A latches off, and must be reset by toggling
POR, before a soft-start can be re-initiated.
Pre-POR Overvoltage Protection
Prior to PVCC, VCC and GVOT exceeding their POR levels, the
ISL6328A is designed to protect either load from any overvoltage
events that may occur. This is accomplished by means of an
internal 10k Ω resistor tied from PHASE to LGATE, which turns on
the lower MOSFET to control the output voltage until the
overvoltage event ceases or the input power supply cuts off. For
complete protection, the low side MOSFET should have a gate
threshold well below the maximum voltage rating of the
load/microprocessor.
Both CORE and NB output support start up into a pre-charged
output.
-
OCL
+
170μA
I 1
Fault Monitoring and Protection
100 μ A
-
OCP
REPEAT FOR EACH
CORE CHANNEL
The ISL6328A actively monitors both CORE and NB output
voltages and currents to detect fault conditions. Fault monitors
trigger protective measures to prevent damage to either load.
One common power-good indicator is provided for linking to
external system monitors. The schematic in Figure 13 outlines
I NB
NB ONLY
+
-
OCP
+
100 μ A
I AVG
CORE ONLY
the interaction between the fault monitors and the power-good
signal.
SOFT-START, FAULT
AND CONTROL LOGIC
Power-Good Signal
The power-good pin (VDDPWRGD) is an open-drain logic output
that signals whether or not the ISL6328A is regulating both NB
and CORE output voltages within the proper levels, and whether
NB ONLY
1.8V
+
OVP
-
any fault conditions exist. This pin should be tied to a +5V source
through a resistor.
During shutdown and soft-start, VDDPWRGD pulls low and
VSEN_NB+
DAC - 300mV
-
+
UV
releases high after a successful soft-start and both output
voltages are operating between the undervoltage and
overvoltage limits. PGOOD transitions low when an undervoltage,
overvoltage, or overcurrent condition is detected on either output
or when the controller is disabled by a POR reset or EN. In the
event of an overvoltage or overcurrent condition, the controller
latches off and PGOOD will not return high. Pending a POR reset
CORE ONLY
1.8V
DAC + 250mV
+
OVP
-
-
OV
+
VDDPWRGD
of the ISL6328A and successful soft-start, the PGOOD will return
high.
Overvoltage Protection
VSEN
DAC - 300mV
-
+
UV
The ISL6328A constantly monitors the sensed output voltage on
the VSEN pin to detect if an overvoltage event occurs. When the
output voltage rises above the OVP trip level and exceeds the
PGOOD OV limit actions are taken by the ISL6328A to protect the
microprocessor load.
21
ISL6328A INTERNAL CIRCUITRY
FIGURE 13. POWER GOOD AND PROTECTION CIRCUITRY
FN7986.0
April 6, 2012
相关PDF资料 |
PDF描述 |
|---|---|
| ICL7665SAIBA-T | IC VOLT DETECTOR OVER/UND 8-SOIC |
| GSC35DRTH-S93 | CONN EDGECARD 70POS DIP .100 SLD |
| ISL6308ACRZ-T | IC CTRLR PWM BUCK 3PHASE 40-QFN |
| GMC35DRTH-S93 | CONN EDGECARD 70POS DIP .100 SLD |
| ISL6563CRZ-TK | IC CTRLR PWM MULTIPHASE 24-QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6328CRZ | 功能描述:IC CTRLR PWM SYNC BUCK DL 48QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:2,000 系列:- 应用:控制器，DSP 输入电压:4.5 V ~ 25 V 输出数:2 输出电压:最低可调至 1.2V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:30-TFSOP（0.173"，4.40mm 宽） 供应商设备封装:30-TSSOP 包装:带卷 (TR) |
| ISL6328CRZ-T | 功能描述:IC CTRLR PWM SYNC BUCK DL 48QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:2,000 系列:- 应用:控制器，DSP 输入电压:4.5 V ~ 25 V 输出数:2 输出电压:最低可调至 1.2V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:30-TFSOP（0.173"，4.40mm 宽） 供应商设备封装:30-TSSOP 包装:带卷 (TR) |
| ISL6328EVAL1Z | 制造商:Intersil Corporation 功能描述:ISL6328 EVALUATION BOARD - 48 LEAD - QFN - ROHS COMPLIANT - Bulk |
| ISL6328IRZ | 功能描述:IC CTRLR PWM SYNC BUCK DL 48QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:2,000 系列:- 应用:控制器，DSP 输入电压:4.5 V ~ 25 V 输出数:2 输出电压:最低可调至 1.2V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:30-TFSOP（0.173"，4.40mm 宽） 供应商设备封装:30-TSSOP 包装:带卷 (TR) |
| ISL6328IRZ-T | 功能描述:IC CTRLR PWM SYNC BUCK DL 48QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:2,000 系列:- 应用:控制器，DSP 输入电压:4.5 V ~ 25 V 输出数:2 输出电压:最低可调至 1.2V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:30-TFSOP（0.173"，4.40mm 宽） 供应商设备封装:30-TSSOP 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。