参数资料
| 型号： | ISL6333CCRZ-T |
| 厂商： | Intersil |
| 文件页数： | 16/40页 |
| 文件大小： | 0K |
| 描述： | IC CTRLR PWM 3PHASE BUCK 48-QFN |
| 标准包装： | 4,000 |
| 应用： | 控制器，Intel VR11 |
| 输入电压： | 5 V ~ 12 V |
| 输出数： | 1 |
| 输出电压： | 0.5 V ~ 1.6 V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 48-VFQFN 裸露焊盘 |
| 供应商设备封装： | 48-QFN（7x7） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页
ISL6333, ISL6333A, ISL6333B, ISL6333C
Functional Pin Descriptions
VCC
VCC is the bias supply for the ICs small-signal circuitry.
Connect this pin to a +5V supply and decouple using a
quality 0.1μF ceramic capacitor.
PVCC1 (ISL6333, ISL6333B Only)
This pin is the input to an internal LDO that regulates the
voltage on the BYP1 pin and should be connected to a +12V
supply. It is very important that this pin is decoupled using a
quality 1.0μF ceramic capacitor.
PVCC2_3 (ISL6333, ISL6333B Only)
This pin is the power supply pin for Channels 2 and 3 lower
MOSFET drivers, and should be connected to a +12V supply.
Decouple this pin with a quality 1.0μF ceramic capacitor.
PVCC1, PVCC2, and PVCC3 (ISL6333A, ISL6333C
Only)
These pins are the power supply pins for Channels 1, 2, and
3 lower MOSFET drivers, and should be connected to a
+12V supply. Decouple these pins with quality 1.0μF
ceramic capacitors
PUVCC
This pin is the power supply pin for Channels 1, 2, and 3
upper MOSFET drivers, and can be connected to any
voltage from +5V to +12V depending on the desired
MOSFET gate-drive level. Decouple this pin with a quality
1.0μF ceramic capacitor.
BYP1 (ISL6333, ISL6333B Only)
This pin is the output of an internal LDO which powers
Channel 1 lower MOSFET driver. A quality 1.0μF ceramic
capacitor should be placed from this pin to ground.
GND
GND is the bias and reference ground for the IC.
EN
This pin is a threshold-sensitive (approximately 0.86V) enable
input for the controllers. Held low, this pin disables controller
operation. Pulled high, the pin enables the controller for
operation.
FS
A resistor, R FS , tied from this pin to ground sets the channel
switching frequency of the controller. Refer to Equation 46
for proper resistor calculation.
The FS pin also determines whether the controllers operate
in the coupled inductor mode or the standard inductor mode
of operation. Tying the R FS resistor to ground will set the
controllers to operate in standard inductor mode. Tying the
R FS resistor to VCC sets the controllers to operate in
coupled inductor mode.
16
VID0, VID1, VID2, VID3, VID4, VID5, VID6, and VID7
These are the inputs for the internal DAC that provide the
reference voltage for output regulation. These pins respond to
TTL logic thresholds. These pins are internally pulled high to
approximately 1.2V, by 40μA internal current sources. The
internal pull-up current decreases to 0 as the VID voltage
approaches the internal pull-up voltage. All VID pins are
compatible with external pull-up voltages not exceeding the
IC’s bias voltage (VCC).
VSEN and RGND
VSEN and RGND are inputs to the precision differential
remote-sense amplifier and should be connected to the sense
pins of the remote load.
VDIFF
VDIFF is the output of the differential remote-sense amplifier.
The voltage on this pin is equal to the difference between
VSEN and RGND.
FB and COMP
These pins are the internal error amplifier inverting input and
output respectively. The FB pin, COMP pin, and the VDIFF
pins are tied together through external R-C networks to
compensate the regulator.
DVC
A series resistor and capacitor can be connected from the
DVC pin to the FB pin to compensate and smooth dynamic
VID transitions.
IDROOP (ISL6333, ISL6333A Only)
The IDROOP pin is the average channel-current sense
output. Connecting this pin directly to FB allows the
converter to incorporate output voltage droop proportional to
the output current. If voltage droop is not desired leave this
pin unconnected.
IMON
The IMON pin is the average channel-current sense output.
This pin is used as a load current indicator to monitor the
output load current.
APA
This is the Adaptive Phase Alignment set pin. A 100μA
current flows into the APA pin and by tying a resistor from
this pin to COMP the trip level for the Adaptive Phase
Alignment circuitry can be set.
REF
The REF input pin is the positive input of the error amplifier. It is
internally connected to the DAC output through a 1k Ω resistor.
A capacitor is used between the REF pin and ground to smooth
the voltage transition during soft-start and Dynamic VID
transitions. This pin can also be bypassed to RGND if desired.
FN6520.3
October 8, 2010
相关PDF资料 |
PDF描述 |
|---|---|
| X40015S8-C | IC VOLTAGE MONITOR DUAL 8-SOIC |
| ISL6323IRZ-T | IC HYBRID CTRLR PWM MONO 48-QFN |
| ADP1715ARMZ-3.0-R7 | IC REG LDO 3V .5A 8-MSOP |
| ISL62882IRTZ-T | IC REG PWM 2PHASE BUCK 40TQFN |
| ISL62882HRTZ-T | IC REG PWM 2PHASE BUCK 40TQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6333CIRZ | 功能描述:IC CTRLR PWM 3PHASE BUCK 48-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
| ISL6333CIRZ-T | 功能描述:IC CTRLR PWM 3PHASE BUCK 48-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
| ISL6333CRZ | 功能描述:IC CTRLR PWM 3PHASE BUCK 48-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
| ISL6333CRZ-T | 功能描述:IC CTRLR PWM 3PHASE BUCK 48-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
| ISL6333IRZ | 功能描述:IC CTRLR PWM 3PHASE BUCK 48-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,000 系列:- 应用:电源，ICERA E400，E450 输入电压:4.1 V ~ 5.5 V 输出数:10 输出电压:可编程 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:42-WFBGA，WLCSP 供应商设备封装:42-WLP 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。