参数资料
| 型号： | ISL6334IRZ-T |
| 厂商： | Intersil |
| 文件页数： | 14/31页 |
| 文件大小： | 0K |
| 描述： | IC CTRLR PWM 4PHASE BUCK 40-QFN |
| 标准包装： | 4,000 |
| 应用： | 控制器，Intel VR11.1 |
| 输入电压： | 3 V ~ 12 V |
| 输出数： | 1 |
| 输出电压： | 0.5 V ~ 1.6 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 40-VFQFN 裸露焊盘 |
| 供应商设备封装： | 40-QFN（6x6） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页当前第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页
ISL6334, ISL6334A
When PSI# is asserted low, indicating the low power mode
operation of the processor, the controller drops the number of
active phases according to the logic on Table 1 for highlight
load efficiency performance. SS and FS pins are used to
program the controller in operation of non-coupled, 2-phase
coupled, or (n-x)-Phase coupled inductors. Different cases yield
different PWM output behaviors on both dropped phase(s) and
remained phase(s) as PSI# is asserted and de-asserted. A high
PSI# input signal pulls the controller back to normal CCM PWM
operation to sustain an immediate heavy transient load and
high efficiency. Note that “n-x” means n-x phase coupled and x
phase(s) are uncoupled.
250
200
150
100
50
TABLE 1. PSI# OPERATION DECODING
0
100k 200k 300k 400k 500k 600k 700k 800k 900k
1M
PSI#
FS
SS
SWITCHING FREQUENCY (Hz)
Non CI or (n-1) CI Drops to 1-phase
Non CI or (n-2) CI Drops to 2-phase
2-phase CI Drops to 1-phase
2-phase CI Drops to 2-phase
Normal CCM PWM Mode
0
0
0
0
1
0
0
1
1
x
0
1
0
1
x
FIGURE 3. SWITCHING FREQUENCY vs RT
Current Sensing
The ISL6334, ISL6334A senses current continuously for fast
response. The ISL6334, ISL6334A supports inductor DCR
sensing, or resistive sensing techniques. The associated
channel current sense amplifier uses the ISEN inputs to
reproduce a signal proportional to the inductor current, I L .
The dropped PWM is forced low for 200ns (uncoupled case)
or until falling edge of coupled PWM (coupled case) then
pulled to VCC/2, while the remained PWM(s) sends out a
special 3-level PWM protocol that the dedicated VR11.1
drivers can decode and then enter diode emulation mode
with gate drive voltage optimization.
The ISL6334A only generates 2-level normal CCM PWM
except for faults. No dedicated VR11.1 driver is required.
While the controller is operational (VCC above POR,
EN_VTT and EN_PWR are both high, valid VID inputs), it
can pull the PWM pins to ~40% of VCC (~2V for 5V VCC
bias) during various stages, such as soft start delay, phase
shedding operation, or fault conditions (OC or OV events).
The matching driver's internal PWM resistor divider can
further raise the PWM potential, but not lower it below the
level set by the controller IC. Therefore, the controller's
PWM outputs are directly compatible with Intersil drivers that
require 5V PWM signal amplitudes. Drivers requiring 3.3V
PWM signal amplitudes are generally incompatible.
Switching Frequency
Switching frequency is determined by the selection of the
frequency-setting resistor, R T , which is connected from FS
pin to GND or VCC. Equation 3 and Figure 3 are provided to
assist in selecting the correct resistor value.
The sense current, I SEN , is proportional to the inductor
current. The sensed current is used for current balance,
load-line regulation, and overcurrent protection.
The internal circuitry, shown in Figures 4, and 5, represents
one channel of an N-channel converter. This circuitry is
repeated for each channel in the converter, but may not be
active depending on the status of the PWM2, PWM3 and
amplifier is typically 60nA; less than 5k Ω input impedance is
preferred to minimized the offset error.
INDUCTOR DCR SENSING
An inductor ’s winding is characteristic of a distributed
resistance, as measured by the DCR (Direct Current
Resistance) parameter. Consider the inductor DCR as a
separate lumped quantity, as shown in Figure 4. The
channel current I L , flowing through the inductor, will also
pass through the DCR. Equation 4 shows the s-domain
equivalent voltage across the inductor V L .
V L ( s ) = I L ? ( s ? L + DCR ) (EQ. 4)
A simple R-C network across the inductor extracts the DCR
voltage, as shown in Figure 4.
R T = --------------------------
10
2.5X10
F SW
where F SW is the switching frequency of each phase.
14
(EQ. 3)
FN6482.2
February 1, 2013
相关PDF资料 |
PDF描述 |
|---|---|
| RCA30DRSZ-S273 | CONN EDGECARD 60POS DIP .125 SLD |
| AMM15DRKH-S13 | CONN EDGECARD 30POS .156 EXTEND |
| GCA30DTMT-S273 | CONN EDGECARD 60POS R/A .125 SLD |
| GSM43DSEN | CONN EDGECARD 86POS .156 EYELET |
| GCA30DTBT-S273 | CONN EDGECARD 60POS R/A .125 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6336ACRZ | 功能描述:IC CTRLR PWM 6PHASE BUCK 48-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
| ISL6336ACRZ-T | 功能描述:IC CTRLR PWM 6PHASE BUCK 48-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
| ISL6336AIRZ | 功能描述:IC CTRLR PWM 6PHASE BUCK 48-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
| ISL6336AIRZ-T | 功能描述:IC CTRLR PWM 6PHASE BUCK 48-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
| ISL6336BCRZ | 功能描述:IC CTRLR PWM SYNC BUCK 48-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,000 系列:- 应用:电源，ICERA E400，E450 输入电压:4.1 V ~ 5.5 V 输出数:10 输出电压:可编程 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:42-WFBGA，WLCSP 供应商设备封装:42-WLP 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。