- 您现在的位置：买卖IC网 > PDF目录15176 > ISL6406IVZ (Intersil)IC REG CTRLR BUCK PWM VM 16TSSOP PDF资料下载
参数资料
| 型号： | ISL6406IVZ |
| 厂商： | Intersil |
| 文件页数： | 12/17页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM VM 16TSSOP |
| 标准包装： | 960 |
| PWM 型： | 电压模式 |
| 输出数： | 1 |
| 频率 - 最大： | 770kHz |
| 占空比： | 100% |
| 电源电压： | 2.97 V ~ 3.63 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 16-TSSOP（0.173"，4.40mm 宽） |
| 包装： | 管件 |
ISL6406
Increasing the value of inductance reduces the ripple current
and voltage. However, the large inductance values reduce
The maximum RMS current required by the regulator may be
closely approximated through Equation 11:
-------------- × ? I OUT
?
+ ------ × ? ----------------------------- × -------------- ? ?
V IN ? ?
L × f s
the converter ’s response time to a load transient.
One of the parameters limiting the converter ’s response to
I RMS
MAX
=
V OUT
V IN
MAX
2
12 ?
1 V IN – V OUT V OUT 2
a load transient is the time required to change the inductor
current. Given a sufficiently fast control loop design, the
ISL6406 will provide either 0% or 100% duty cycle in
response to a load transient. The response time is the time
required to slew the inductor current from an initial current
value to the transient current level. During this interval, the
difference between the inductor current and the transient
current level must be supplied by the output capacitor.
Minimizing the response time can minimize the output
capacitance required.
The response time to a transient is different for the
application of load and the removal of load. Equations 9 and
10 give the approximate response time interval for
application and removal of a transient load:
(EQ. 11)
For a through-hole design, several electrolytic capacitors may
be needed. For surface mount designs, solid tantalum
capacitors can be used, but caution must be exercised with
regard to the capacitor surge current rating. These capacitors
must be capable of handling the surge-current at power-up.
Some capacitor series available from reputable manufacturers
are surge current tested.
MOSFET Selection/Considerations
The ISL6406 requires two N-Channel power MOSFETs.
These should be selected based upon r DS(ON) , gate supply
requirements, and thermal management requirements.
In high-current applications, the MOSFET power dissipation,
t RISE =
L x I TRAN
V IN - V OUT
(EQ. 9)
package selection and heatsink are the dominant design
factors. The power dissipation includes two loss components;
conduction loss and switching loss. The conduction losses are
t FALL =
L x I TRAN
V OUT
(EQ. 10)
the largest component of power dissipation for both the upper
and the lower MOSFETs. These losses are distributed between
the two MOSFETs according to duty factor.
P UPPER = Io × r DS ( ON ) × D + --- ? Io × V IN × t SW × f s
where: I TRAN is the transient load current step, t RISE is the
response time to the application of load, and t FALL is the
response time to the removal of load. The worst case
response time can be either at the application or removal of
load. Be sure to check both of these equations at the
minimum and maximum output levels for the worst case
response time.
Input Capacitor Selection
Use a mix of input bypass capacitors to control the voltage
overshoot across the MOSFETs. Use small ceramic
capacitors for high frequency decoupling and bulk capacitors
to supply the current needed each time Q 1 turns on. Place the
small ceramic capacitors physically close to the MOSFETs
and between the drain of Q 1 and the source of Q 2 .
The important parameters for the bulk input capacitor are the
voltage rating and the RMS current rating. For reliable
operation, select the bulk capacitor with voltage and current
ratings above the maximum input voltage and largest RMS
current required by the circuit. The capacitor voltage rating
should be at least 1.25x greater than the maximum input
voltage and a voltage rating of 1.5x is a conservative
guideline. The RMS current rating requirement for the input
The switching losses seen when sourcing current will be
different from the switching losses seen when sinking current.
When sourcing current, the upper MOSFET realizes most of
the switching losses. The lower switch realizes most of the
switching losses when the converter is sinking current (see
Equations 13 and 14). These equations assume linear
voltage-current transitions and do not adequately model power
loss due the reverse-recovery of the upper and lower
MOSFET’s body diode.
The gate-charge losses are dissipated by the ISL6406 and
don't heat the MOSFETs. However, large gate-charge
increases the switching interval, t SW which increases the
MOSFET switching losses. Ensure that both MOSFETs are
within their maximum junction temperature at high ambient
temperature by calculating the temperature rise according to
package thermal-resistance specifications. A separate heatsink
may be necessary depending upon MOSFET power, package
type, ambient temperature and air flow.
Losses while sourcing current:
2 1
2
P LOWER = Io 2 x r DS(ON) x (1 - D)
capacitor of a buck regulator is approximately 1/2 the DC
load current.
Losses while sinking current:
P UPPER = Io 2 x r DS(ON) x D
(EQ. 12)
P LOWER = Io × r DS ( ON ) × ( 1 – D ) + --- ? Io × V IN × t SW × f s
2 1
2
Where: D is the duty cycle = V OUT / V IN ,
t SW is the combined switch ON and OFF time, and
f s is the switching frequency.
12
FN9073.8
September 4, 2009
相关PDF资料 |
PDF描述 |
|---|---|
| H2BBT-10112-A8-ND | JUMPER-H1500TR/A3048A/H1500TR12" |
| ISL6406IRZ | IC REG CTRLR BUCK PWM VM 16-QFN |
| RBA40DRMN | CONN EDGECARD 80POS .125 SQ WW |
| ISL6406IBZ | IC REG CTRLR BUCK PWM VM 16-SOIC |
| H2BBT-10112-Y8-ND | JUMPER-H1500TR/A3048Y/H1500TR12" |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6406IVZ-T | 功能描述:电压模式 PWM 控制器 VER OF ISL6406IV-T RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| ISL6406MREPZ | 制造商:Intersil Corporation 功能描述:V62/08610-01XE, -55 TO 125C PB-FREE VID VERSION OF THE ISL64 - Rail/Tube |
| ISL6406MREPZ-TK | 制造商:Intersil Corporation 功能描述:V62/08610-01XE, -55 TO 125C PB-FREE VID VERSION OF THE ISL64 - Tape and Reel |
| ISL6406MVEP | 制造商:Intersil Corporation 功能描述:SOFT SW PWM CNTRLR 1-OUT SYNCH BUCK PWM CNTRLR 3.3V/5V 100KH - Rail/Tube |
| ISL6406MVEP-TK | 制造商:Intersil Corporation 功能描述:SOFT SW PWM CNTRLR 1-OUT SYNCH BUCK PWM CNTRLR 3.3V/5V 100KH - Tape and Reel |
发布紧急采购，3分钟左右您将得到回复。