- 您现在的位置：买卖IC网 > PDF目录15176 > ISL6406IVZ (Intersil)IC REG CTRLR BUCK PWM VM 16TSSOP PDF资料下载
参数资料
| 型号： | ISL6406IVZ |
| 厂商： | Intersil |
| 文件页数： | 6/17页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM VM 16TSSOP |
| 标准包装： | 960 |
| PWM 型： | 电压模式 |
| 输出数： | 1 |
| 频率 - 最大： | 770kHz |
| 占空比： | 100% |
| 电源电压： | 2.97 V ~ 3.63 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 16-TSSOP（0.173"，4.40mm 宽） |
| 包装： | 管件 |
ISL6406
Pin Descriptions
CPVOUT - This pin represents the output of the charge
pump. The voltage at this pin is the bias voltage for the IC.
Connect a decoupling capacitor from this pin to ground. The
value of the decoupling capacitor should be at least 10x the
value of the charge pump capacitor. This pin may be tied to
the bootstrap circuit as the source for creating the BOOT
voltage.
CT1 and CT2 - These pins are the connections for the
external charge pump capacitor. A minimum of a 0.1μF
ceramic capacitor is recommended for proper operation of
the IC.
OCSET - Connect a resistor (r OCSET ) from this pin to the
drain of the upper MOSFET (V IN ). r OCSET , an internal 20μA
current source (I OCSET ), and the upper MOSFET
ON-resistance (r DS(ON) ) set the converter overcurrent (OC)
trip point according to Equation 1:
BOOT - This pin provides ground referenced bias voltage to
the upper MOSFET driver. A bootstrap circuit is used to
create a voltage suitable to drive a logic-level N-Channel
MOSFET. A large (~1M Ω ) resistor should be connected from
this pin to GND. The purpose of this resistor is to discharge
the BOOT pin during a shutdown condition,
SYNC/EN = LOW so that the gate drivers are quickly
powered off by this bleed resistor.
UGATE - Connect this pin to the upper MOSFET’s gate. This
pin provides the PWM-controlled gate drive for the upper
MOSFET. This pin is also monitored by the adaptive
shoot-through protection circuitry to determine when the
upper MOSFET has turned off.
GND - This pin represents the signal and power ground for
the IC. Tie this pin to the ground island/plane through the
lowest impedance connection available.
r DS ( ON )
( I OCSET ) ( R OCSET )
I PEAK = --------------------------------------------------------
An overcurrent trip cycles the soft-start function.
(EQ. 1)
LGATE - Connect this pin to the lower MOSFET’s gate. This
pin provides the PWM-controlled gate drive for the lower
MOSFET. This pin is also monitored by the adaptive
shoot-through protection circuitry to determine when the
lower MOSFET has turned off.
VOUT - This pin provides the external switcher output
voltage to the IC as feedback for the 1.8V fixed output
voltage option. Leave this pin open on the ISL6406 for the
adjustable output voltage option.
VCC - This pin provides bias supply for the ISL6406.
COMP and FB - COMP and FB are the available external
pins of the error amplifier. The FB pin is the inverting input of
the internal error amplifier and the COMP pin is the error
amplifier output. These pins are used to compensate the
control feedback loop of the converter.
Connect a well-coupled 3.3V supply to this pin.
CPGND - This pin represents the signal and power ground
PHASE - Connect this pin to the upper MOSFET’s source.
This pin is used to monitor the voltage drop across the upper
for the charge pump. Tie this pin to the ground island/plane
through the lowest impedance connection available.
MOSFET for overcurrent protection.
SYNC/EN - This is a dual-function pin. To synchronize with
RT - Connect an external resistor from this pin to ground for
frequency selection. Refer to Figure 3 (RT vs Frequency).
6
an external clock, apply a clock with a frequency 1.1x to 2.0x
higher than the part’s natural frequency to this pin. The
device may be disabled by tying this pin to ground. In this
shutdown mode, all functions are disabled and the device
will draw <50μA supply current.
FN9073.8
September 4, 2009
相关PDF资料 |
PDF描述 |
|---|---|
| H2BBT-10112-A8-ND | JUMPER-H1500TR/A3048A/H1500TR12" |
| ISL6406IRZ | IC REG CTRLR BUCK PWM VM 16-QFN |
| RBA40DRMN | CONN EDGECARD 80POS .125 SQ WW |
| ISL6406IBZ | IC REG CTRLR BUCK PWM VM 16-SOIC |
| H2BBT-10112-Y8-ND | JUMPER-H1500TR/A3048Y/H1500TR12" |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6406IVZ-T | 功能描述:电压模式 PWM 控制器 VER OF ISL6406IV-T RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| ISL6406MREPZ | 制造商:Intersil Corporation 功能描述:V62/08610-01XE, -55 TO 125C PB-FREE VID VERSION OF THE ISL64 - Rail/Tube |
| ISL6406MREPZ-TK | 制造商:Intersil Corporation 功能描述:V62/08610-01XE, -55 TO 125C PB-FREE VID VERSION OF THE ISL64 - Tape and Reel |
| ISL6406MVEP | 制造商:Intersil Corporation 功能描述:SOFT SW PWM CNTRLR 1-OUT SYNCH BUCK PWM CNTRLR 3.3V/5V 100KH - Rail/Tube |
| ISL6406MVEP-TK | 制造商:Intersil Corporation 功能描述:SOFT SW PWM CNTRLR 1-OUT SYNCH BUCK PWM CNTRLR 3.3V/5V 100KH - Tape and Reel |
发布紧急采购，3分钟左右您将得到回复。