- 您现在的位置：买卖IC网 > PDF目录15180 > ISL6440IAZ-TK (Intersil)IC REG CTRLR BUCK PWM CM 24-QSOP PDF资料下载
参数资料
| 型号： | ISL6440IAZ-TK |
| 厂商： | Intersil |
| 文件页数： | 9/15页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM CM 24-QSOP |
| 产品培训模块： | Solutions for Industrial Control Applications |
| 标准包装： | 1,000 |
| PWM 型： | 电流模式 |
| 输出数： | 2 |
| 频率 - 最大： | 340kHz |
| 占空比： | 93% |
| 电源电压： | 4.5 V ~ 24 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 24-SSOP（0.154"，3.90mm 宽） |
| 包装： | 带卷 (TR) |
ISL6440
Soft-Start Operation
When soft-start is initiated, the voltage on the SS pin of the
enabled PWM channels starts to ramp gradually, due to the
T SOFT = 0.8V ? ----------- ?
V OUTx = 0.8V ? ---------------------- ?
5 μ A current sourced into the external capacitor. The output
voltage follows the soft-start voltage.
When the SS pin voltage reaches 0.8V, the output voltage of
the enabled PWM channel reaches the regulation point, and
the soft-start pin voltage continues to rise. At this point the
PGOOD and fault circuitry is enabled. This completes the
soft-start sequence. Any further rise of SS pin voltage does
not affect the output voltage. By varying the values of the
soft-start capacitors, it is possible to provide sequencing of the
main outputs at start-up. The soft-start time can be obtained
from the following equation:
C SS
? 5 μ A ?
VCC5 1V/DIV
V OUT1 1V/DIV
SS1 1V/DIV
FIGURE 13. SOFT-START OPERATION
The soft-start capacitors can be chosen to provide startup
tracking for the two PWM outputs. This can be achieved by
choosing the soft-start capacitors such that the soft-start
capacitor ration equals the respective PWM output voltage
ratio. For example, if I use PWM1 = 1.2V and PWM2 = 3.3V
then the soft-start capacitor ration should be, C SS1 /C SS1 =
1.2/3.3 = 0.364. Figure 14 shows that soft-start waveform
with C SS1 = 0.01μF and C SS2 = 0.027μF.
9
V OUT1 1V/DIV
V OUT2 1V/DIV
FIGURE 14. PWM1 AND PWM2 OUTPUT TRACKING DURING
STARTUP
Output Voltage Programming
A resistive divider from the output to ground sets the output
voltage of either PWM channel. The center point of the
divider shall be connected to FBx pin. The output voltage
value is determined by the following equation.
R1 + R2
? R2 ?
where R1 is the top resistor of the feedback divider network
and R2 is the resistor connected from FB1 or FB2 to ground.
Out-of-Phase Operation
The two PWM controllers in the ISL6440 operate 180 o out-
of-phase to reduce input ripple current. This reduces the
input capacitor ripple current requirements, reduces power
supply-induced noise, and improves EMI. This effectively
helps to lower component cost, save board space and
reduce EMI.
Dual PWMs typically operate in-phase and turn on both
upper FETs at the same time. The input capacitor must then
support the instantaneous current requirements of both
controllers simultaneously, resulting in increased ripple
voltage and current. The higher RMS ripple current lowers
the efficiency due to the power loss associated with the ESR
of the input capacitor. This typically requires more low-ESR
capacitors in parallel to minimize the input voltage ripple and
ESR-related losses, or to meet the required ripple current
rating.
With dual synchronized out-of-phase operation, the high-
side MOSFETs of the ISL6440 turn on 180 o out-of-phase.
The instantaneous input current peaks of both regulators no
longer overlap, resulting in reduced RMS ripple current and
input voltage ripple. This reduces the required input
capacitor ripple current rating, allowing fewer or less
expensive capacitors, and reducing the shielding
requirements for EMI. The typical operating curves show the
synchronized 180 degree out-of-phase operation.
FN9040.2
October 4, 2005
相关PDF资料 |
PDF描述 |
|---|---|
| VE-25P-EY-F4 | CONVERTER MOD DC/DC 13.8V 50W |
| SH472M010ST | CAP ALUM 4700UF 10V 20% RADIAL |
| H2ABT-10110-W4-ND | JUMPER-H1502TR/A2015W/H1500TR10" |
| VI-B4J-EV-F3 | CONVERTER MOD DC/DC 36V 150W |
| CAT706ZI-GT3 | IC SUPERVISOR CIRCUIT 8-MSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6441IR | 功能描述:IC CTRLR SGL/STEP DOWN PWM 28QFN RoHS:否 类别:集成电路 (IC) >> PMIC - 电源管理 - 专用 系列:- 应用说明:Ultrasound Imaging Systems Application Note 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:37 系列:- 应用:医疗用超声波成像，声纳 电流 - 电源:- 电源电压:2.37 V ~ 6 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:56-WFQFN 裸露焊盘 供应商设备封装:56-TQFN-EP（8x8） 包装:管件 |
| ISL6441IR-T | 功能描述:IC CTRLR PWM DUAL 1.4MHZ 28-QFN RoHS:否 类别:集成电路 (IC) >> PMIC - 电源管理 - 专用 系列:- 应用说明:Ultrasound Imaging Systems Application Note 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:37 系列:- 应用:医疗用超声波成像，声纳 电流 - 电源:- 电源电压:2.37 V ~ 6 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:56-WFQFN 裸露焊盘 供应商设备封装:56-TQFN-EP（8x8） 包装:管件 |
| ISL6441IR-TK | 功能描述:IC CTRLR PWM DUAL 1.4MHZ 28-QFN RoHS:否 类别:集成电路 (IC) >> PMIC - 电源管理 - 专用 系列:- 应用说明:Ultrasound Imaging Systems Application Note 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:37 系列:- 应用:医疗用超声波成像，声纳 电流 - 电源:- 电源电压:2.37 V ~ 6 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:56-WFQFN 裸露焊盘 供应商设备封装:56-TQFN-EP（8x8） 包装:管件 |
| ISL6441IRZ | 功能描述:IC CTRLR SGL/STEP DOWN PWM 28QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电源管理 - 专用 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:50 系列:- 应用:热电冷却器 电流 - 电源:- 电源电压:3 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.173"，4.40mm 宽）裸露焊盘 供应商设备封装:28-TSSOP 裸露焊盘 包装:管件 产品目录页面:1410 (CN2011-ZH PDF) |
| ISL6441IRZS2695 | 制造商:Intersil Corporation 功能描述: |
发布紧急采购，3分钟左右您将得到回复。