- 您现在的位置：买卖IC网 > PDF目录15193 > ISL6522IVZ-T (Intersil)IC REG CTRLR BST PWM VM 14-TSSOP PDF资料下载
参数资料
| 型号： | ISL6522IVZ-T |
| 厂商： | Intersil |
| 文件页数： | 6/15页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BST PWM VM 14-TSSOP |
| 标准包装： | 2,500 |
| PWM 型： | 电压模式 |
| 输出数： | 1 |
| 频率 - 最大： | 1MHz |
| 占空比： | 100% |
| 电源电压： | 10.8 V ~ 13.2 V |
| 降压： | 是 |
| 升压： | 是 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 14-TSSOP（0.173"，4.40mm 宽） |
| 包装： | 带卷 (TR) |
ISL6522
I OCS ? R OCSET
r DS ( ON )
OCSET
Connect a resistor (R OCSET ) from this pin to the drain of the
upper MOSFET. R OCSET , an internal 200 μ A current source
(I OCS ), and the upper MOSFET on-resistance (r DS(ON) ) set
the converter overcurrent (OC) trip point according to the
following equation:
I PEAK = --------------------------------------------
An overcurrent trip cycles the soft-start function.
SS
Connect a capacitor from this pin to ground. This capacitor,
along with an internal 10 μ A current source, sets the soft-start
interval of the converter.
COMP and FB
COMP and FB are the available external pins of the error
amplifier. The FB pin is the inverting input of the error
amplifier and the COMP pin is the error amplifier output.
These pins are used to compensate the voltage-control
feedback loop of the converter.
EN
This pin is the open-collector enable pin. Pull this pin below
1V to disable the converter. In shutdown, the soft-start pin is
discharged and the UGATE and LGATE pins are held low.
GND
Signal ground for the IC. All voltage levels are measured
with respect to this pin.
PHASE
Connect the PHASE pin to the upper MOSFET source. This
pin is used to monitor the voltage drop across the MOSFET
for overcurrent protection. This pin also provides the return
path for the upper gate drive.
UGATE
Connect UGATE to the upper MOSFET gate. This pin
provides the gate drive for the upper MOSFET. This pin is also
monitored by the adaptive shoot through protection circuitry to
determine when the upper MOSFET has turned off.
BOOT
This pin provides bias voltage to the upper MOSFET driver.
A bootstrap circuit may be used to create a BOOT voltage
suitable to drive a standard N-Channel MOSFET.
PGND
This is the power ground connection. Tie the lower MOSFET
source to this pin.
6
LGATE
Connect LGATE to the lower MOSFET gate. This pin provides
the gate drive for the lower MOSFET. This pin is also
monitored by the adaptive shoot through protection circuitry to
determine when the lower MOSFET has turned off.
PVCC
Provide a bias supply for the lower gate drive to this pin.
VCC
Provide a 12V bias supply for the chip to this pin.
Functional Description
Initialization
The ISL6522 automatically initializes upon receipt of power.
Special sequencing of the input supplies is not necessary.
The Power-On Reset (POR) function continually monitors
the input supply voltages and the enable (EN) pin. The POR
monitors the bias voltage at the VCC pin and the input
voltage (V IN ) on the OCSET pin. The level on OCSET is
equal to V IN Less a fixed voltage drop (see overcurrent
protection). With the EN pin held to V CC , the POR function
initiates soft-start operation after both input supply voltages
exceed their POR thresholds. For operation with a single
+12V power source, V IN and V CC are equivalent and the
+12V power source must exceed the rising V CC threshold
before POR initiates operation.
The POR function inhibits operation with the chip disabled
(EN pin low). With both input supplies above their POR
thresholds, transitioning the EN pin high initiates a soft-start
interval.
Soft-Start
The POR function initiates the soft-start sequence. An internal
10 μ A current source charges an external capacitor (C SS ) on
the SS pin to 4V. Soft-start clamps the error amplifier output
(COMP pin) to the SS pin voltage. Figure 3 shows the soft-
start interval. At t 1 in Figure 3, the SS and COMP voltages
reach the valley of the oscillator’s triangle wave. The
oscillator’s triangular waveform is compared to the ramping
error amplifier voltage. This generates PHASE pulses of
increasing width that charge the output capacitor(s). This
interval of increasing pulse width continues to t2, at which
point the output is in regulation and the clamp on the COMP
pin is released. This method provides a rapid and controlled
output voltage rise.
FN9030.8
March 10, 2006
相关PDF资料 |
PDF描述 |
|---|---|
| GCM43DCMH | CONN EDGECARD 86POS .156 WW |
| ISL88001IH23Z-T | IC VOLT SUPERVISOR 2.32V SOT23-3 |
| VE-JTM-EW-F2 | CONVERTER MOD DC/DC 10V 100W |
| ABC07DRYS-S734 | CONN EDGECARD 14POS DIP .100 SLD |
| ASC10DRTS-S734 | CONN EDGECARD 20POS DIP .100 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6522IVZ-TS2698 | 制造商:Intersil Corporation 功能描述:PB-FREE 14LD. TSSOP, T&R, PWM CONTROLLER- DRR REGUALTOR - Tape and Reel 制造商:Intersil Corporation 功能描述:IC REG CTRLR BUCK PWM 14TSSOP 制造商:Intersil 功能描述:14LD PWM CNTRLR- DRRGUALTOR |
| ISL6523ACB | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| ISL6523CB | 功能描述:IC CTRLR VRM8.5 PWM DUAL 28-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,000 系列:- 应用:电源，ICERA E400，E450 输入电压:4.1 V ~ 5.5 V 输出数:10 输出电压:可编程 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:42-WFBGA，WLCSP 供应商设备封装:42-WLP 包装:带卷 (TR) |
| ISL6523CB-T | 功能描述:IC CTRLR VRM8.5 PWM DUAL 28-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,000 系列:- 应用:电源，ICERA E400，E450 输入电压:4.1 V ~ 5.5 V 输出数:10 输出电压:可编程 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:42-WFBGA，WLCSP 供应商设备封装:42-WLP 包装:带卷 (TR) |
| ISL6523CBZ | 功能描述:IC CTRLR VRM8.5 PWM DUAL 28-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。