参数资料
| 型号： | ISL6531CB |
| 厂商： | Intersil |
| 文件页数： | 13/17页 |
| 文件大小： | 0K |
| 描述： | IC CONTROLLER INTEL 24SOIC |
| 标准包装： | 30 |
| 应用： | 控制器，Intel Pentium? III，IV |
| 输入电压： | 4.5 V ~ 5.5 V |
| 输出数： | 2 |
| 输出电压： | 2.5V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 24-SOIC |
| 包装： | 管件 |
ISL6531
could cancel the usefulness of these low inductance
components. Consult with the manufacturer of the load on
specific decoupling requirements.
Use only specialized low-ESR capacitors intended for
switching-regulator applications for the bulk capacitors. The
bulk capacitor’s ESR will determine the output ripple voltage
and the initial voltage drop after a high slew-rate transient. An
aluminum electrolytic capacitor’s ESR value is related to the
case size with lower ESR available in larger case sizes.
However, the equivalent series inductance (ESL) of these
capacitors increases with case size and can reduce the
usefulness of the capacitor to high slew-rate transient loading.
Unfortunately, ESL is not a specified parameter. Work with
your capacitor supplier and measure the capacitor’s
impedance with frequency to select a suitable component. In
most cases, multiple electrolytic capacitors of small case size
perform better than a single large case capacitor.
Output Inductor Selection
The output inductor is selected to meet the output voltage
ripple requirements and minimize the converter’s response
time to the load transient. Additionally, the output inductor for
the V TT regulator has to meet the minimum value criteria for
loop stability as described in the V TT Feedback
Compensation section. The inductor value determines the
converter’s ripple current and the ripple voltage is a function
response time to the removal of load. The worst case
response time can be either at the application or removal of
load. Be sure to check both of these equations at the
minimum and maximum output levels for the worst case
response time.
Input Capacitor Selection
Use a mix of input bypass capacitors to control the voltage
overshoot across the MOSFETs. Use small ceramic
capacitors for high frequency decoupling and bulk capacitors
to supply the current needed each time Q 1 turns on. Place the
small ceramic capacitors physically close to the MOSFETs
and between the drain of Q 1 and the source of Q 2 .
The important parameters for the bulk input capacitor are the
voltage rating and the RMS current rating. For reliable
operation, select the bulk capacitor with voltage and current
ratings above the maximum input voltage and largest RMS
current required by the circuit. The capacitor voltage rating
should be at least 1.25 times greater than the maximum
input voltage and a voltage rating of 1.5 times is a
conservative guideline. The RMS current rating requirement
for the input capacitor of a buck regulator is approximately
1/2 the DC load current.
The maximum RMS current required by the regulator may be
closely approximated through the following equation:
---------------- × ? I OUT
1 ? V IN – V OUT V OUT ? 2 ?
L × f s
? V IN ? ?
of the ripple current. The ripple voltage and current are
approximated by the following equations:
I RMS
MAX
=
V OUT ?
V IN ?
MAX
2
+ ------ × ? -------------------------------- × ---------------- ? ?
12
? I =
V IN - V OUT
f s x L
x
V OUT
V IN
? V OUT = ? I x ESR
For a through hole design, several electrolytic capacitors may
be needed. For surface mount designs, solid tantalum
Increasing the value of inductance reduces the ripple current
and voltage. However, the large inductance values reduce
the converter’s response time to a load transient.
One of the parameters limiting the converter’s response to
a load transient is the time required to change the inductor
current. Given a sufficiently fast control loop design, the
ISL6531 will provide either 0% or 100% duty cycle in
response to a load transient. The response time is the time
required to slew the inductor current from an initial current
value to the transient current level. During this interval the
difference between the inductor current and the transient
current level must be supplied by the output capacitor.
Minimizing the response time can minimize the output
capacitance required.
The response time to a transient is different for the
application of load and the removal of load. The following
equations give the approximate response time interval for
application and removal of a transient load:
capacitors can be used, but caution must be exercised with
regard to the capacitor surge currentrating. These capacitors
must be capable of handling the surge-current at power-up.
Some capacitor series available from reputable manufacturers
are surge current tested.
MOSFET Selection/Considerations
The ISL6531 requires two N-Channel power MOSFETs for
each PWM regulator. These should be selected based upon
r DS(ON) , gate supply requirements, and thermal management
requirements.
In high-current applications, the MOSFET power dissipation,
package selection and heatsink are the dominant design
factors. The power dissipation includes two loss components;
conduction loss and switching loss. The conduction losses are
the largest component of power dissipation for both the upper
and the lower MOSFETs. These losses are distributed between
the two MOSFETs according to duty factor. The switching
losses seen when sourcing current will be different from the
t RISE =
L x I TRAN
V IN - V OUT
t FALL =
L x I TRAN
V OUT
switching losses seen when sinking current. The V DDQ
regulator will only source current while the V TT regulator can
sink and source. When sourcing current, the upper MOSFET
where: I TRAN is the transient load current step, t RISE is the
response time to the application of load, and t FALL is the
13
realizes most of the switching losses. The lower switch realizes
most of the switching losses when the converter is sinking
相关PDF资料 |
PDF描述 |
|---|---|
| RMM30DRSI | CONN EDGECARD 60POS DIP .156 SLD |
| ABC26DRTH | CONN EDGECARD 52POS .100 DIP SLD |
| ISL6444CA | IC CONTROLLER DDR 28-QSOP |
| EMM22DTAN-S664 | CONN EDGECARD 44POS R/A .156 SLD |
| ACB20DHNR | CONN EDGECARD 40POS .050 DIP SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6531CB-T | 功能描述:IC CONTROLLER INTEL 24SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,000 系列:- 应用:电源，ICERA E400，E450 输入电压:4.1 V ~ 5.5 V 输出数:10 输出电压:可编程 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:42-WFBGA，WLCSP 供应商设备封装:42-WLP 包装:带卷 (TR) |
| ISL6531CBZ | 功能描述:IC CONTROLLER INTEL 24SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,000 系列:- 应用:电源，ICERA E400，E450 输入电压:4.1 V ~ 5.5 V 输出数:10 输出电压:可编程 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:42-WFBGA，WLCSP 供应商设备封装:42-WLP 包装:带卷 (TR) |
| ISL6531CBZ-T | 功能描述:IC CONTROLLER INTEL 24SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,000 系列:- 应用:电源，ICERA E400，E450 输入电压:4.1 V ~ 5.5 V 输出数:10 输出电压:可编程 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:42-WFBGA，WLCSP 供应商设备封装:42-WLP 包装:带卷 (TR) |
| ISL6531CR | 功能描述:IC CONTROLLER INTEL 32QFN RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,000 系列:- 应用:电源，ICERA E400，E450 输入电压:4.1 V ~ 5.5 V 输出数:10 输出电压:可编程 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:42-WFBGA，WLCSP 供应商设备封装:42-WLP 包装:带卷 (TR) |
| ISL6531CR-T | 功能描述:IC CONTROLLER INTEL 32QFN RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,000 系列:- 应用:电源，ICERA E400，E450 输入电压:4.1 V ~ 5.5 V 输出数:10 输出电压:可编程 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:42-WFBGA，WLCSP 供应商设备封装:42-WLP 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。