参数资料
| 型号： | ISL6531CRZ |
| 厂商： | Intersil |
| 文件页数： | 10/17页 |
| 文件大小： | 0K |
| 描述： | IC CONTROLLER INTEL 32QFN |
| 标准包装： | 60 |
| 应用： | 控制器，Intel Pentium? III，IV |
| 输入电压： | 4.5 V ~ 5.5 V |
| 输出数： | 2 |
| 输出电压： | 2.5V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-VFQFN 裸露焊盘 |
| 供应商设备封装： | 32-QFN（5x5） |
| 包装： | 管件 |
ISL6531
normal operating load range, find the R OCSET resistor from
the equation above with:
1. The maximum r DS(ON) at the highest junction
ISL6531
+5V
I PEAK > I OUT ( MAX ) + ( --------- I - ) ,
3. Determine I PEAK for
temperature.
2. The minimum I OCSET from the specification table.
?
2
where ? I is the output inductor ripple current.
UGATE1
PHASE1
LGATE1
V DDQ
DDR
SDRAM
For an equation for the ripple current see the section under
component guidelines titled Output Inductor Selection .
UGATE2
PHASE2
LGATE2
V TT
R T
+
-
A small ceramic capacitor should be placed in parallel with
R OCSET to smooth the voltage across R OCSET in the
presence of switching noise on the input voltage.
Current Sinking
The ISL6531 V TT regulator incorporates a MOSFET shoot-
through protection method which allows the converter to sink
current as well as source current. Care should be exercised
when designing a converter with the ISL6531 when it is
known that the converter may sink current.
When the converter is sinking current, it is behaving as a
boost converter that is regulating its input voltage. This
means that the converter is boosting current into the input
rail of the regulator. If there is nowhere for this current to go,
such as to other distributed loads on the rail or through a
voltage limiting protection device, the capacitance on this rail
will absorb the current. This situation will the allow voltage
level of the input rail to increase. If the voltage level of the rail
is boosted to a level that exceeds the maximum voltage
rating of any components attached to the input rail, then
those components may experience an irreversible failure or
experience stress that may shorten their lifespan. Ensuring
that there is a path for the current to flow other than the
capacitance on the rail will prevent this failure mode.
To insure that the current does not boost up the input rail
voltage of the V TT regulator, it is recommended that the
input rail of the V TT regulator be the output of the V DDQ
regulator. The current being sunk by the V TT regulator will
be fed into the V DDQ rail and then drawn into the DDR
SDRAM memory module and back into the V TT regulator.
Figure 6 shows the recommended configuration and the
resulting current loop.
V REF
FIGURE 6. V TT CURRENT SINKING LOOP
Application Guidelines
Layout Considerations
Layout is very important in high frequency switching
converter design. With power devices switching efficiently at
300kHz, the resulting current transitions from one device to
another cause voltage spikes across the interconnecting
impedances and parasitic circuit elements. These voltage
spikes can degrade efficiency, radiate noise into the circuit,
and lead to device over-voltage stress. Careful component
layout and printed circuit board design minimizes the voltage
spikes in the converters.
As an example, consider the turn-off transition of the PWM
MOSFET. Prior to turn-off, the MOSFET is carrying the full
load current. During turn-off, current stops flowing in the
MOSFET and is picked up by the lower MOSFET. Any
parasitic inductance in the switched current path generates a
large voltage spike during the switching interval. Careful
component selection, tight layout of the critical components,
and short, wide traces minimizes the magnitude of voltage
spikes.
There are two sets of critical components in a DC-DC
converter using the ISL6531. The switching components are
the most critical because they switch large amounts o
energy, and therefore tend to generate large amounts of
noise. Next are the small signal components which connect
to sensitive nodes or supply critical bypass current and
signal coupling.
A multi-layer printed circuit board is recommended. Figure 7
shows the connections of the critical components in the
converter. Note that capacitors C IN and C OUT could each
represent numerous physical capacitors. Dedicate one solid
layer, usually a middle layer of the PC board, for a ground
plane and make all critical component ground connections
with vias to this layer. Dedicate another solid layer as a
power plane and break this plane into smaller islands of
common voltage levels. Keep the metal runs from the
PHASE terminals to the output inductor short. The power
plane should support the input power and output power
10
相关PDF资料 |
PDF描述 |
|---|---|
| 4554-120K | INDUCTOR RF 12UH 10% RADIAL |
| AGM15DRSH | CONN EDGECARD 30POS DIP .156 SLD |
| GSM06DTAN-S273 | CONN EDGECARD 12POS R/A .156 SLD |
| AYM15DRSD | CONN EDGECARD 30POS DIP .156 SLD |
| ESM36DRSD-S664 | CONN EDGECARD 72POS DIP .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6531CRZ-T | 功能描述:IC CONTROLLER INTEL 32QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,000 系列:- 应用:电源，ICERA E400，E450 输入电压:4.1 V ~ 5.5 V 输出数:10 输出电压:可编程 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:42-WFBGA，WLCSP 供应商设备封装:42-WLP 包装:带卷 (TR) |
| ISL6531EVAL1 | 功能描述:EVALUATION BOARD 1 ISL6531 RoHS:否 类别:编程器，开发系统 >> 过时/停产零件编号 系列:- 标准包装:1 系列:- 传感器类型:CMOS 成像，彩色（RGB） 传感范围:WVGA 接口:I²C 灵敏度:60 fps 电源电压:5.7 V ~ 6.3 V 嵌入式:否 已供物品:成像器板 已用 IC / 零件:KAC-00401 相关产品:4H2099-ND - SENSOR IMAGE WVGA COLOR 48-PQFP4H2094-ND - SENSOR IMAGE WVGA MONO 48-PQFP |
| ISL6531EVAL2 | 功能描述:EVALUATION BOARD 2 ISL6531 RoHS:否 类别:编程器，开发系统 >> 过时/停产零件编号 系列:- 标准包装:1 系列:- 传感器类型:CMOS 成像，彩色（RGB） 传感范围:WVGA 接口:I²C 灵敏度:60 fps 电源电压:5.7 V ~ 6.3 V 嵌入式:否 已供物品:成像器板 已用 IC / 零件:KAC-00401 相关产品:4H2099-ND - SENSOR IMAGE WVGA COLOR 48-PQFP4H2094-ND - SENSOR IMAGE WVGA MONO 48-PQFP |
| ISL6532ACR | 功能描述:IC REG/CTRLR ACPI DUAL DDR 28QFN RoHS:否 类别:集成电路 (IC) >> PMIC - 电源管理 - 专用 系列:- 应用说明:Ultrasound Imaging Systems Application Note 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:37 系列:- 应用:医疗用超声波成像，声纳 电流 - 电源:- 电源电压:2.37 V ~ 6 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:56-WFQFN 裸露焊盘 供应商设备封装:56-TQFN-EP（8x8） 包装:管件 |
| ISL6532ACR-T | 功能描述:IC REG/CTRLR ACPI DUAL DDR 28QFN RoHS:否 类别:集成电路 (IC) >> PMIC - 电源管理 - 专用 系列:- 应用说明:Ultrasound Imaging Systems Application Note 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:37 系列:- 应用:医疗用超声波成像，声纳 电流 - 电源:- 电源电压:2.37 V ~ 6 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:56-WFQFN 裸露焊盘 供应商设备封装:56-TQFN-EP（8x8） 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。