参数资料
型号: ISL6553EVAL1
厂商: Intersil
文件页数: 4/9页
文件大小: 0K
描述: EVALUATION BOARD ISL6553
标准包装: 1
系列: Endura™
主要目的: 特殊用途 DC/DC,VRM 电源
输出及类型: 1,非隔离
功率 - 输出: 45W
输出电压: 1.5V
电流 - 输出: 30A
输入电压: 5V,12V
稳压器拓扑结构: 降压
频率 - 开关: 350kHz
板类型: 完全填充
已供物品:
已用 IC / 零件: HIP6601,ISL6553
Application Note AN9961
load and the PGOOD signal transitions high once the soft-
start cycle is complete.
Core Voltage (1V/div)
0V
Output Current (20A/div)
0A
PWM1 (5V/div)
Adapting Circuit Performance
This evaluation board showcases one solution to meet the
present requirements of voltage regulator modules powering
Intel Pentium III processors. The balance between meeting
specifications and cost can be tilted depending on the
performance expectations desired. For example,
implementation cost could be reduced if additional
motherboard space is available. The OSCON output
capacitors could be replaced with less costly aluminum
capacitors with higher ESR, but more than four capacitors
would be required to meet the same transient specifications.
Efficiency could be improved by selecting MOSFETs with a
slightly lower r DS(on) and comparable total gate charge.
0V
0V
PGOOD (5V/div)
5ms/div
Summary
The ISL6553EVAL1 is an adaptable evaluation tool which
showcases the performance of the ISL6553 / HIP6601A chip
set. Designed to meet the performance requirements of
FIGURE 7. RESPONSE TO TEMPORARY OUTPUT SHORT
Under most circumstances an overcurrent event will remain
until the fault is found and removed. The ISL6553 will
continue to cycle through the same delay time and soft-start
cycle sequence until that time. The worst-case power
delivered during overcurrent cycling is less than that of
normal operation due to the addition of delay time. Indefinite
overcurrent cycling does not create any thermal issues.
Efficiency
The performance of the ISL6553EVAL1 board loaded from
5A to 30A is plotted in Figure 8. The measurements were
made at thermal equilibrium under room temperature
conditions with no air flow.
95
90
85
80
75
Intel’s VRM-8.5 specification, the board allows the user the
flexibility to configure the board for current as well as future
microprocessor offerings.
The following pages provide a schematic of the board, bill of
materials and layout drawings to support implementation of
this solution.
References
Intersil documents are available on the web at
http://www.intersil.com/.
[1] ISL6553 Data Sheet, Intersil Corporation, FN4931
[2] HIP6601A/HIP6603A Data Sheet, Intersil Corporation,
FN4819
[3] HIP6602A Data Sheet, Intersil Corporation, FN4902
70
5
10
15
20
25
30
OUTPUT CURRENT (A)
FIGURE 8. EFFICIENCY vs LOAD CURRENT
4
相关PDF资料
PDF描述
ISL6558EVAL2 EVAL BOARD W/6605 DRVRS ISL6558
ISL6559EVAL2 EVALUATION BOARD 2 ISL6559
ISL6562EVAL1 EVALUATION BOARD ISL6562
ISL6594BCRZ-T IC MOSFET DVR SYNC BUCK 10-DFN
ISL6594DCRZ IC MOSFET DRVR SYNC BUCK 10-DFN
相关代理商/技术参数
参数描述
ISL6554CB 功能描述:IC PWM CORE VOLTAGE REG 20-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,000 系列:- 应用:电源,ICERA E400,E450 输入电压:4.1 V ~ 5.5 V 输出数:10 输出电压:可编程 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:42-WFBGA,WLCSP 供应商设备封装:42-WLP 包装:带卷 (TR)
ISL6554CB-T 功能描述:IC PWM CORE VOLTAGE REG 20-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,000 系列:- 应用:电源,ICERA E400,E450 输入电压:4.1 V ~ 5.5 V 输出数:10 输出电压:可编程 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:42-WFBGA,WLCSP 供应商设备封装:42-WLP 包装:带卷 (TR)
ISL6554CB-TR5165 制造商:Rochester Electronics LLC 功能描述: 制造商:Intersil Corporation 功能描述:
ISL6554CBZ 功能描述:IC PWM CORE VOLTAGE REG 20-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,000 系列:- 应用:电源,ICERA E400,E450 输入电压:4.1 V ~ 5.5 V 输出数:10 输出电压:可编程 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:42-WFBGA,WLCSP 供应商设备封装:42-WLP 包装:带卷 (TR)
ISL6554CBZA 功能描述:IC PWM CORE VOLTAGE REG 20-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,000 系列:- 应用:电源,ICERA E400,E450 输入电压:4.1 V ~ 5.5 V 输出数:10 输出电压:可编程 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:42-WFBGA,WLCSP 供应商设备封装:42-WLP 包装:带卷 (TR)