- 您现在的位置：买卖IC网 > Datasheet目录334 > ISL6610IRZ (Intersil)IC MOSFET DRVR DUAL SYNC 16-QFN Datasheet资料下载
参数资料
| 型号： | ISL6610IRZ |
| 厂商： | Intersil |
| 文件页数： | 8/11页 |
| 文件大小： | 0K |
| 描述： | IC MOSFET DRVR DUAL SYNC 16-QFN |
| 标准包装： | 75 |
| 配置： | 高端和低端，同步 |
| 输入类型： | PWM |
| 延迟时间： | 18ns |
| 配置数： | 2 |
| 输出数： | 4 |
| 高端电压 - 最大（自引导启动）： | 36V |
| 电源电压： | 4.5 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-VQFN 裸露焊盘 |
| 供应商设备封装： | 16-QFN-EP（4x4） |
| 包装： | 管件 |
ISL6610, ISL6610A
PVCC
BOOT
C GD
D
profile MOSFETs, such as Direct FETs and multi-SOURCE
leads devices (SO-8, LFPAK, PowerPAK), have low parasitic
lead inductances and can be driven by either ISL6610 or
ISL6610A (assuming proper layout design). The ISL6610,
R HI1
R LO1
UGATE
G
R G1
R GI1
C GS
C DS
Q1
missing the 3 Ω integrated BOOT resistor, typically yields
slightly higher efficiency than the ISL6610A.
Layout Considerations
S
PHASE
FIGURE 3. TYPICAL UPPER-GATE DRIVE TURN-ON PATH
PVCC
D
A good layout helps reduce the ringing on the switching
node (PHASE) and significantly lower the stress applied to
the output drives. The following advice is meant to lead to an
optimized layout and performance:
? Keep decoupling loops (VCC-GND, PVCC-PGND and
BOOT-PHASE) short and wide, at least 25 mils. Avoid
using vias on decoupling components other than their
R HI2
R LO2
LGATE
GND
G
R G2
C GD
R GI2
C GS
S
C DS
Q2
ground terminals, which should be on a copper plane with
at least two vias.
? Minimize trace inductance, especially on low-impedance
lines. All power traces (UGATE, PHASE, LGATE, PGND,
PVCC, VCC, GND) should be short and wide, at least 25
mils. Try to place power traces on a single layer,
otherwise, two vias on interconnection are preferred
where possible. For no connection (NC) pins on the QFN
FIGURE 4. TYPICAL LOWER-GATE DRIVE TURN-ON PATH
Application Information
MOSFET and Driver Selection
The parasitic inductances of the PCB and of the power
devices’ packaging (both upper and lower MOSFETs) can
cause serious ringing, exceeding absolute maximum rating
of the devices. The negative ringing at the edges of the
PHASE node could increase the bootstrap capacitor voltage
through the internal bootstrap diode, and in some cases, it
may overstress the upper MOSFET driver. Careful layout,
proper selection of MOSFETs and packaging, as well as the
proper driver can go a long way toward minimizing such
unwanted stress.
part, connect it to the adjacent net (LGATE2/PHASE2) can
reduce trace inductance.
? Shorten all gate drive loops (UGATE-PHASE and LGATE-
PGND) and route them closely spaced.
? Minimize the inductance of the PHASE node. Ideally, the
source of the upper and the drain of the lower MOSFET
should be as close as thermally allowable.
? Minimize the current loop of the output and input power
trains. Short the source connection of the lower MOSFET
to ground as close to the transistor pin as feasible. Input
capacitors (especially ceramic decoupling) should be
placed as close to the drain of upper and source of lower
MOSFETs as possible.
? Avoid routing relatively high impedance nodes (such as
PWM and ENABLE lines) close to high dV/dt UGATE and
PHASE nodes.
PVCC
BOOT
D
In addition, connecting the thermal pad of the QFN package
to the power ground through multiple vias, or placing a low
noise copper plane (such as power ground) underneath the
R HI1
G
SOIC part is recommended. This is to improve heat
R LO1
UGATE
Q1
dissipation and allow the part to achieve its full thermal
potential.
R PH =1-2 Ω
S
PHASE
FIGURE 5. PHASE RESISTOR TO MINIMIZE SERIOUS
NEGATIVE PHASE SPIKE
The selection of D 2 -PAK, or D-PAK packaged MOSFETs, is
a much better match (for the reasons discussed) for the
ISL6610A with a phase resistor, as shown in Figure 5. Low-
8
Upper MOSFET Self Turn-On Effects At Startup
Should the driver have insufficient bias voltage applied, its
outputs are floating. If the input bus is energized at a high
dV/dt rate while the driver outputs are floating, due to the
self-coupling via the internal C GD of the MOSFET, the
UGATE could momentarily rise up to a level greater than the
threshold voltage of the MOSFET. This could potentially turn
on the upper switch and result in damaging inrush energy.
FN6395.0
November 22, 2006
相关PDF资料 |
PDF描述 |
|---|---|
| ISL6612ACBZ | IC DRIVER MOSFET SYNC BUCK 8SOIC |
| ISL6612BCBZ | IC DRIVER MOSFET SYNC BUCK 8SOIC |
| ISL6613IR-T | IC MOSFET DRVR SYNC BUCK 10-DFN |
| ISL6614AIR-T | IC DRIVER DUAL SYNC BUCK 16-QFN |
| ISL6614BIRZ | IC DRVR DUAL SYNC BUCK 16-QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6610IRZ-T | 功能描述:IC MOSFET DRVR DUAL SYNC 16-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - MOSFET，电桥驱动器 - 外部开关 系列:- 标准包装:6,000 系列:* |
| ISL6611ACRZ | 功能描述:IC REG CTRLR DOUBLER PWM 16-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:275kHz 占空比:50% 电源电压:18 V ~ 110 V 降压:无 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) |
| ISL6611ACRZ-T | 功能描述:IC REG CTRLR DOUBLER PWM 16-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:275kHz 占空比:50% 电源电压:18 V ~ 110 V 降压:无 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) |
| ISL6611AIRZ | 功能描述:IC REG CTRLR DOUBLER PWM 16-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:275kHz 占空比:50% 电源电压:18 V ~ 110 V 降压:无 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) |
| ISL6611AIRZ-T | 功能描述:IC REG CTRLR DOUBLER PWM 16-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:275kHz 占空比:50% 电源电压:18 V ~ 110 V 降压:无 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。