参数资料
| 型号： | ISL6721AV |
| 厂商： | Intersil |
| 文件页数： | 16/22页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR PWM CM 16-TSSOP |
| 标准包装： | 96 |
| PWM 型： | 电流模式 |
| 输出数： | 1 |
| 频率 - 最大： | 1MHz |
| 占空比： | 100% |
| 电源电压： | 9 V ~ 18 V |
| 降压： | 是 |
| 升压： | 是 |
| 回扫： | 是 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 是 |
| 工作温度： | -40°C ~ 105°C |
| 封装/外壳： | 16-TSSOP（0.173"，4.40mm 宽） |
| 包装： | 管件 |
ISL6721
I spk ( max )
The loop compensation is placed around the Error Amplifier
(EA) on the secondary side of the converter. The primary
side amplifier located in the control IC is used as a unity gain
inverting amplifier and provides no loop compensation. A
Type 2 error amplifier configuration was selected as a
precaution in case operation in continuous mode should
occur at some operating point.
K = --------------------------
V c ( max )
R o = LoadResis tan ce
L s = SecondaryInduc tan ce
(EQ. 28)
(EQ. 29)
(EQ. 30)
ω p = --------------------
f p = -----------------------------
ω z = --------------------
f z = --------------------------------------
V OUT
2
R o ? C o
1
R c ? C o
or
or
1
π ? R o ? C o
1
2 ? π ? R c ? C o
(EQ. 31)
(EQ. 32)
V ERROR
-
C o = OutputCapaci tan ce
(EQ. 33)
+
REF
R c = OutputCapaci tan ceE SR
V c ( max ) = ControlVoltageRange
(EQ. 34)
(EQ. 35)
FIGURE 8. TYPE 2 ERROR AMPLIFIER
Development of a small signal model for current mode
control is rather complex. The method of reference 1 was
selected for its ability to accurately predict loop behavior. To
The value of K may be determined by assuming all of the
output power is delivered by the 3.3V output at the threshold
of current limit. The maximum power allowed was
determined earlier as 15W, therefore:
2 ? ------------ ? t sw
P out
2 ? -------- ? 5 × 10
I spk ( max ) = ------------------------------------ = ------------------------------------------ = 19.5
2.33 × 10
v c ( max ) = V ISENSE ? A EXT ? A CS ? --------------------- = 2.93
further simplify the analysis, the converter will be modeled as
a single output supply with all of the output capacitance
reflected to the 3.3V output. Once the “single” output system
is compensated, adjustments to the compensation will be
required based on actual loop measurements.
The first parameter to determine is the peak current
V out 3.3
Tr – 6
15 – 6
1
A COMP
A
(EQ. 36)
V
(EQ. 37)
f pc = ------------------------------------------------------------ ≈ --------------------------------------------
2 ? π ? R 15 ? C 14 ? C 13
2 ? π ? R 15 ? C 14
feedback loop gain. Since this application is low power, a
resistor in series with the source of the power switching
MOSFET is used for the current feedback signal. For higher
power applications, a resistor would dissipate too much
power and current transformer would be used instead.
There is limited flexibility to adjust the current loop behavior
due to the need to provide overcurrent protection. Current
limit and the current loop gain are determined by the current
sense resistor and the ISET threshold. ISET was set at 1.0V,
near its maximum, to minimize noise effects. When
determining ISET, the internal gain and offset of the ISENSE
signal in the control IC must be taken into account. The
where A EXT is the external gain of the current feedback
network, A CS is the IC internal gain, and A COMP is the gain
between the error amplifier and the PWM comparator.
The Type 2 compensation configuration has two poles and
one zero. The first pole is at the origin, and provides the
integration characteristic which results in excellent DC
regulation. Referring to the Typical Application Schematic on
located at:
C 13 + C 14 1
(EQ. 38)
f zc = --------------------------------------------
maximum peak primary current was determined earlier to be
1.87A, so a choice of 2.25A peak primary current for current
limit is reasonable. A current gain, A EXT , of 0.5V/A was
1
2 ? π ? R 15 ? C 13
(EQ. 39)
selected to achieve this.
The ratio of R 15 to the parallel combination of R 17 and R 18
ISET = 2.25 ? 0.8 ? 0.5 + 0.100 = 1.00
V
(EQ. 26)
determine the mid band gain of the error amplifier.
1 + ------
v o R o ? L s ? f sw ω z
v c
1 + -------
A midband = ------------------------------------------------
R 17 ? R 18
s
------ = K ? --------------------------------- ? ----------------- (EQ. 27)
2 s
ω p
If we ignore the current feedback sampled-data effects:
16
R 15 ? ( R 17 + R 18 )
(EQ. 40)
From Equation 27, it can be seen that the control to output
transfer function frequency dependence is a function of the
output load resistance, the value of output capacitance, and
the output capacitance ESR. These variations must be
considered when compensating the control loop. The worst
case small signal operating point for the converter is at
FN9110.6
March 5, 2008
相关PDF资料 |
PDF描述 |
|---|---|
| ISL6723AABZ | IC REG CTRLR PWM CM 16-SOIC |
| ISL6726AAZ-T7A | IC REG CTRLR ISO PWM CM 20-QSOP |
| ISL6729IU-T | IC REG CTRLR BST FLYBK ISO 8MSOP |
| ISL6740AIVZA | IC REG CTRLR PWM VM 16-TSSOP |
| ISL6741IV-T | IC REG CTRLR PWM CM 16-TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6721AV-T | 功能描述:电流型 PWM 控制器 FLEXIBLE SINGLE END CUR MODE PWM RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| ISL6721AVZ | 功能描述:电流型 PWM 控制器 FLEX SNG ENDED CUR MODE PWM CONTRLR RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| ISL6721AVZ-T | 功能描述:IC REG CTRLR PWM CM 16-TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:275kHz 占空比:50% 电源电压:18 V ~ 110 V 降压:无 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) |
| ISL6721EVAL1 | 功能描述:EVALUATION BOARD ISL6721 RoHS:否 类别:RF/IF 和 RFID >> RF 评估和开发套件，板 系列:- 标准包装:1 系列:- 类型:GPS 接收器 频率:1575MHz 适用于相关产品:- 已供物品:模块 其它名称:SER3796 |
| ISL6721EVAL3Z | 功能描述:EVAL BOARD 3 FOR ISL6721 RoHS:是 类别:编程器，开发系统 >> 评估板 - DC/DC 与 AC/DC（离线）SMPS 系列:* 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:True Shutdown™ 主要目的:DC/DC，步升 输出及类型:1，非隔离 功率 - 输出:- 输出电压:- 电流 - 输出:1A 输入电压:2.5 V ~ 5.5 V 稳压器拓扑结构:升压 频率 - 开关:3MHz 板类型:完全填充 已供物品:板 已用 IC / 零件:MAX8969 |
发布紧急采购，3分钟左右您将得到回复。