参数资料
| 型号： | ISL78205AVEZ |
| 厂商： | Intersil |
| 文件页数： | 2/19页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK SYNC ADJ 20HTSSOP |
| 标准包装： | 740 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 可调至 0.8V |
| 输入电压： | 3 V ~ 40 V |
| PWM 型： | 电流模式 |
| 频率 - 开关： | 200kHz ~ 2.2MHz |
| 电流 - 输出： | 2.5A |
| 同步整流器： | 两者兼有 |
| 工作温度： | -40°C ~ 105°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-TSSOP（0.173"，4.40mm 宽）裸露焊盘 |
| 包装： | 管件 |
| 供应商设备封装： | 20-HTSSOP |
ISL78205
Pin Configuration
PGND 1
BOOT 2
VIN 3
VIN 4
ISL78205
(20 LD HTSSOP)
TOP VIEW
20 LGATE
19 SYNC
18 NC
17 PHASE
SGND 5
VCC 6
NC 7
EN 8
FS 9
SS 10
Functional Pin Description
21
PAD
16 PHASE
15 PGOOD
14 DGND
13 ILIMIT
12 COMP
11 FB
PIN NAME
PGND
BOOT
VIN
SGND
VCC
EN
FS
SS
FB
COMP
ILIMIT
DGND
PGOOD
PHASE
SYNC
PIN #
1
2
3, 4
5
6
8
9
10
11
12
13
14
15
16, 17
19
DESCRIPTION
This pin is used as the ground connection of the power flow, including the driver.
This pin provides bias voltage to the high-side MOSFET driver. A bootstrap circuit is used to create a voltage suitable to drive
the internal N-channel MOSFET. The boot charge circuitries are integrated inside of the IC. No external boot diode is needed.
A 1μF ceramic capacitor is recommended to be used between the BOOT and PHASE pin.
Connect the input rail to these pins that are connected to the drain of the integrated high-side MOSFET, as well as the source
for the internal linear regulator that provides the bias of the IC.
With the part switching, the operating input voltage applied to the VIN pins must be under 40V. This recommendation allows
for short voltage ringing spikes (within a couple of ns time range) due to switching while not exceeding Absolute Maximum
Ratings.
This pin provides the return path for the control and monitor portions of the IC.
This pin is the output of the internal linear regulator that supplies the bias for the IC, including the driver. A minimum 4.7μF
decoupling ceramic capacitor is recommended between VCC to ground.
The controller is enabled when this pin is pulled HIGH or left floating. The IC is disabled when this pin is pulled LOW. Range:
0V to 5.5V.
Tying this pin to VCC, or GND, or leaving it open will force the IC to have 500kHz switching frequency. The oscillator switching
frequency can also be programmed by adjusting the resistor from this pin to GND.
Connect a capacitor from this pin to ground. This capacitor, along with an internal 5μA current source, sets the soft-start
interval of the converter. Also, this pin can be used to track a ramp on this pin.
This pin is the inverting input of the voltage feedback error amplifier. With a properly selected resistor divider connected from
V OUT to FB, the output voltage can be set to any voltage between the input rail (reduced by maximum duty cycle and voltage
drop) and the 0.8V reference. Loop compensation is achieved by connecting an RC network across COMP and FB. The FB pin
is also monitored for overvoltage events.
Output of the voltage feedback error amplifier.
Programmable current limit pin. With this pin connected to VCC pin, or to GND, or left open, the current limit threshold is set
to a default of 3.6A; the current limit threshold can be programmed with a resistor from this pin to GND.
Digital ground pin. Connect to SGND at quiet ground copper plane.
PGOOD is an open drain output. Pull up this pin with a resistor to VCC. PGOOD pin will be pulled low immediately in the event
that the output is out of regulation (OV or UV) or the EN pin is pulled low. PGOOD is equipped with a fixed delay of 1000 cycles
upon output power-up (V O > 90%).
These pins are the PHASE nodes that should be connected to the output inductor. These pins are connected to the source of
the high side N-channel MOSFET.
This pin can be used to synchronize two or more ISL78205 controllers. Multiple ISL78205s can be synchronized with their
SYNC pins connected together. 180 degree phase shift is automatically generated between the master and slave ICs.
The internal oscillator can also lock to an external frequency source applied to this pin with square pulse waveform (with
frequency 10% higher than the IC’s local frequency, and pulse width higher than 150ns).
This pin should be left floating if not used.
2
FN7926.3
February 19, 2014
相关PDF资料 |
PDF描述 |
|---|---|
| ISL78210ARUZ-T | IC REG MULTI-OUTPUT 32TQFP |
| ISL78211ARZ | IC REG 1PHASE BUCK 40QFN |
| ISL78213ARZ | IC REG BUCK SYNC ADJ 3A 16VQFN |
| ISL78214ARZ | IC REG BUCK SYNC ADJ 4A 16QFN |
| ISL78215AUZ | IC REG CTRLR BST FLYBK ISO 8MSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL78205AVEZ-T | 功能描述:IC REG BUCK SYNC ADJ 20HTSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:两者兼有 输出数:1 输出电压:5V，1 V ~ 10 V 输入电压:3.5 V ~ 28 V PWM 型:电流模式 频率 - 开关:220kHz ~ 1MHz 电流 - 输出:600mA 同步整流器:无 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:16-SSOP（0.154"，3.90mm 宽） 包装:带卷 (TR) 供应商设备封装:16-QSOP |
| ISL78205AVEZ-TR5303 | 制造商:Intersil Corporation 功能描述:HARMAN BECKER ISL78205AVEZ-T W/SPECIAL CHANGE CONTROL, 12 MO - Tape and Reel |
| ISL78208 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Wide VIN Dual Standard Buck Regulator with 3A/3A Continuous Output Current |
| ISL78208ARZ | 制造商:Intersil Corporation 功能描述:ISL78208ARZ AUTOMOTIVE GRADE - 3A STANDARD BUCK REGULATOR - - Rail/Tube 制造商:Intersil Corporation 功能描述:IC REG BUCK SYNC ADJ 3A 32-QFN 制造商:Intersil Corporation 功能描述:DC-DC CONV, BUCK, ADJ, 2MHZ, QFN-32, Primary Input Voltage:28V, No. of Outputs:2, Output Current:3A, No. of Pins:32, Operating Temperature Min:-40C, Operating Temperature Max:105C, Package / Case:32-QFN , RoHS Compliant: Yes |
| ISL78208ARZ-T | 制造商:Intersil Corporation 功能描述:ISL78208ARZ AUTOMOTIVE GRADE 3A STANDARD BUCK REGULATOR - 5X - Tape and Reel 制造商:Intersil Corporation 功能描述:IC REG BUCK SYNC ADJ 3A 32-QFN 制造商:Intersil Corporation 功能描述:DC-DC CONV, BUCK, ADJ, 2MHZ, QFN-32, Primary Input Voltage:28V, No. of Outputs:2, Output Current:3A, No. of Pins:32, Operating Temperature Min:-40C, Operating Temperature Max:105C, Package / Case:32-QFN , RoHS Compliant: Yes |
发布紧急采购，3分钟左右您将得到回复。