参数资料
| 型号： | ISL81487LIBZ-T |
| 厂商： | Intersil |
| 文件页数： | 11/14页 |
| 文件大小： | 0K |
| 描述： | IC TXRX RS485/422 5V HS 8-SOIC |
| 标准包装： | 2,500 |
| 类型： | 收发器 |
| 驱动器/接收器数： | 1/1 |
| 规程： | RS422，RS485 |
| 电源电压： | 4.5 V ~ 5.5 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOICN |
| 包装： | 带卷 (TR) |
6
FN6051.7
February 27, 2006
Receiver Enable from Shutdown to
Output High
tZH(SHDN) CL = 15pF, SW = GND, (Figure 5, Notes 7, 9)
Full
-
800
2500
ns
Receiver Enable from Shutdown to
Output Low
tZL(SHDN) CL = 15pF, SW = VCC, (Figure 5, Notes 7, 9)
Full
-
800
2500
ns
SWITCHING CHARACTERISTICS (ISL81487L)
Driver Input to Output Delay
tPLH, tPHL RDIFF = 54, CL = 100pF, (Figure 2)
Full
150
650
1200
ns
Driver Output Skew
tSKEW
RDIFF = 54, CL = 100pF, (Figure 2)
Full
-
160
600
ns
Driver Differential Rise or Fall Time
tR, tF
RDIFF = 54, CL = 100pF, (Figure 2)
Full
250
900
1200
ns
Driver Enable to Output High
tZH
CL = 100pF, SW = GND, (Figure 3, Note 5)
Full
100
1000
1500
ns
Driver Enable to Output Low
tZL
CL = 100pF, SW = VCC, (Figure 3, Note 5)
Full
100
1000
1500
ns
Driver Disable from Output High
tHZ
CL = 15pF, SW = GND, (Figure 3)
Full
150
750
1500
ns
Driver Disable from Output Low
tLZ
CL = 15pF, SW = VCC, (Figure 3)
Full
150
750
1500
ns
Receiver Input to Output Delay
tPLH, tPHL (Figure 4)
Full
30
175
250
ns
Receiver Skew | tPLH - tPHL |tSKD
(Figure 4)
25
-
13
-
ns
Receiver Enable to Output High
tZH
CL = 15pF, SW = GND, (Figure 5, Note 6)
Full
-
10
50
ns
Receiver Enable to Output Low
tZL
CL = 15pF, SW = VCC, (Figure 5, Note 6)
Full
-
10
50
ns
Receiver Disable from Output High
tHZ
CL = 15pF, SW = GND, (Figure 5)
Full
-
10
50
ns
Receiver Disable from Output Low
tLZ
CL = 15pF, SW = VCC, (Figure 5)
Full
-
10
50
ns
Maximum Data Rate
fMAX
Full
250
-
kbps
Time to Shutdown
tSHDN
(Note 7)
Full
50
140
600
ns
Driver Enable from Shutdown to
Output High
tZH(SHDN) CL = 100pF, SW = GND, (Figure 3, Notes 7, 8)
Full
-
1100
2000
ns
Driver Enable from Shutdown to
Output Low
tZL(SHDN) CL = 100pF, SW = VCC, (Figure 3, Notes 7, 8)
Full
-
1000
2000
ns
Receiver Enable from Shutdown to
Output High
tZH(SHDN) CL = 15pF, SW = GND, (Figure 5, Notes 7, 9)
Full
-
900
2000
ns
Receiver Enable from Shutdown to
Output Low
tZL(SHDN) CL = 15pF, SW = VCC, (Figure 5, Notes 7, 9)
Full
-
900
2000
ns
ESD PERFORMANCE
RS-485 Pins (A/Y, B/Z)
Human Body Model
25
-
±15
-
kV
All Other Pins
25
-
>
±7-
kV
NOTES:
2. Currents into device pins are positive; currents out of device pins are negative. Voltages are referenced to ground unless otherwise specified.
3. Supply current specification is valid for loaded drivers when DE = 0V.
4. Applies to peak current. See “Typical Performance Curves” for more information.
5. When testing the ISL8487E and ISL81487L, keep RE = 0 to prevent the device from entering SHDN.
6. When testing the ISL8487E and ISL81487L, the RE signal high time must be short enough (typically <200ns) to prevent the device from entering
SHDN.
7. The ISL8487E and ISL81487L are put into shutdown by bringing RE high and DE low. If the inputs are in this state for less than 50ns, the parts
are guaranteed not to enter shutdown. If the inputs are in this state for at least 600ns, the parts are guaranteed to have entered shutdown. See
“Low-Power Shutdown Mode” section.
8. Keep RE = VCC, and set the DE signal low time >600ns to ensure that the device enters SHDN.
9. Set the RE signal high time >600ns to ensure that the device enters SHDN.
10. Devices meeting these limits are denoted as “1/8 unit load (1/8 UL)” transceivers. The RS-485 standard allows up to 32 Unit Loads on the bus,
so there can be 256 1/8 UL devices on a bus.
Electrical Specifications
Test Conditions: VCC = 4.5V to 5.5V; Unless Otherwise Specified.
Typicals are at VCC = 5V, TA = 25°C, (Note 2) (Continued)
PARAMETER
SYMBOL
TEST CONDITIONS
TEMP
(°C)
MIN
TYP
MAX
UNITS
ISL8487E, ISL81487L, ISL81487E
相关PDF资料 |
PDF描述 |
|---|---|
| MAX159BEUA+T | IC ADC 10BIT 108KSPS 8-UMAX |
| VI-B6H-IV-F4 | CONVERTER MOD DC/DC 52V 150W |
| MS3100E22-23P | CONN RCPT 8POS WALL MNT W/PINS |
| GTC06AF-16-10S | CONN PLUG 3POS STRAIGHT W/SCKT |
| MAX1238LEEE+ | IC ADC 12BIT SERIAL 16-QSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL81487LIP | 功能描述:IC TXRX RS-485/422 ESD 8-DIP RoHS:否 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 标准包装:1,000 系列:- 类型:收发器 驱动器/接收器数:2/2 规程:RS232 电源电压:3 V ~ 5.5 V 安装类型:表面贴装 封装/外壳:16-SOIC（0.295"，7.50mm 宽） 供应商设备封装:16-SOIC 包装:带卷 (TR) |
| ISL81487LIPZ | 功能描述:IC TXRX RS-485/422 ESD 5V 8-PDIP RoHS:是 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 标准包装:250 系列:- 类型:收发器 驱动器/接收器数:2/2 规程:RS232 电源电压:3 V ~ 5.5 V 安装类型:表面贴装 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:16-TSSOP 包装:带卷 (TR) |
| ISL8200AM | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Complete Current Share 10A DC/DC Power Module |
| ISL8200AMEV1PHZ | 功能描述:电源管理IC开发工具 ISL8200M EVAL RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| ISL8200AMIRZ | 功能描述:DC/DC转换器 10A DC/DC Buck Power Supply Module RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
发布紧急采购，3分钟左右您将得到回复。