参数资料
| 型号： | ISL84684IIZ-T |
| 厂商： | Intersil |
| 文件页数： | 9/11页 |
| 文件大小： | 0K |
| 描述： | IC SWITCH DUAL SPDT 10WLCSP |
| 标准包装： | 1 |
| 功能： | 开关 |
| 电路： | 2 x SPDT |
| 导通状态电阻： | 500 毫欧 |
| 电压电源： | 单电源 |
| 电压 - 电源，单路/双路(±)： | 1.8 V ~ 4.5 V |
| 电流 - 电源： | 5nA |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-UFBGA，WLCSP |
| 供应商设备封装： | 10-WLCSP（2.0x1.5） |
| 包装： | 剪切带 (CT) |
| 其它名称： | ISL84684IIZ-TCT |
7
FN6190.0
November 3, 2005
Detailed Description
The ISL84684II is a bidirectional, dual single pole/double
throw (SPDT) analog switch that offers precise switching
capability from a single 1.8V to 4.5V supply with low on-
resistance (0.21
) and high speed operation (tON = 43ns,
tOFF = 27ns). The device is especially well suited for
portable battery powered equipment due to its low operating
supply voltage (1.8V), low power consumption (0.32
W max),
low leakage currents (150nA max), and the tiny chipscale
package. The ultra low on-resistance and RON flatness
provide very low insertion loss and distortion to applications
that require signal reproduction.
Supply Sequencing and Overvoltage Protection
With any CMOS device, proper power supply sequencing is
required to protect the device from excessive input currents
which might permanently damage the IC. All I/O pins contain
ESD protection diodes from the pin to V+ and to GND (see
Figure 8). To prevent forward biasing these diodes, V+ must
be applied before any input signals, and the input signal
voltages must remain between V+ and GND.
If these conditions cannot be guaranteed, then precautions
must be implemented to prohibit the current and voltage at
the logic pin and signal pins from exceeding the maximum
ratings of the switch. The following two methods can be used
to provide additional protection to limit the current in the
event that the voltage at a signal pin or logic pin goes below
ground or above the V+ rail.
Logic inputs can be protected by adding a 1k
resistor in
series with the logic input (see Figure 8). The resistor limits
the input current below the threshold that produces
permanent damage, and the sub-microamp input current
produces an insignificant voltage drop during normal
operation.
This method is not acceptable for the signal path inputs.
Adding a series resistor to the switch input defeats the
purpose of using a low RON switch. Connecting schottky
diodes to the signal pins as shown in Figure 8 will shunt the
fault current to the supply or to ground thereby protecting the
switch. These schottky diodes must be sized to handle the
expected fault current.
Power-Supply Considerations
The ISL84684II construction is typical of most single supply
CMOS analog switches, in that they have two supply pins;
V+ and GND. V+ and GND drive the internal CMOS
switches and set their analog voltage limits. Unlike switches
with a 4V maximum supply voltage, the ISL84684II 5V
maximum supply voltage provides plenty of room for the
10% tolerance of a 4.3V supply, as well as room for
overshoot and noise spikes.
FIGURE 6. CROSSTALK TEST CIRCUIT
FIGURE 7. CAPACITANCE TEST CIRCUIT
Test Circuits and Waveforms (Continued)
0V or V+
ANALYZER
V+
C
NO or NC
SIGNAL
GENERATOR
RL
GND
IN1
COM
50
N.C.
COM
NC or NO
Signal direction through switch is reversed, worst case values
are recorded. Repeat test for all switches.
V+
C
GND
NO or NC
COM
IN
IMPEDANCE
ANALYZER
0V or V+
Repeat test for all switches.
FIGURE 8. OVERVOLTAGE PROTECTION
GND
VCOM
VNX
V+
INX
OPTIONAL
PROTECTION
RESISTOR
OPTIONAL
SCHOTTKY
DIODE
OPTIONAL
SCHOTTKY
DIODE
ISL84684II
相关PDF资料 |
PDF描述 |
|---|---|
| ISL84684IU-T | IC SWITCH DUAL SPDT 10MSOP |
| ISL84714IH-T | IC SWITCH SPDT SC70-6 |
| ISL84715IH-T | IC SWITCH SPST SC70-5 |
| ISL84762IU-T | IC SWITCH DUAL SPDT 10MSOP |
| ISL84780IV-T | IC SWITCH QUAD SPDT 16TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL84684IIZ-TS | 制造商:Rochester Electronics LLC 功能描述: 制造商:Intersil Corporation 功能描述: |
| ISL84684IIZ-TS2038 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Intersil Corporation 功能描述: |
| ISL84684IR | 功能描述:IC SWITCH DUAL SPDT 10TDFN RoHS:否 类别:集成电路 (IC) >> 接口 - 模拟开关，多路复用器，多路分解器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:36 系列:- 功能:多路复用器 电路:2 x 4:1 导通状态电阻:75 欧姆 电压电源:单/双电源 电压 - 电源，单路/双路(±):2 V ~ 12 V，±2 V ~ 6 V 电流 - 电源:- 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:20-SOIC（0.295"，7.50mm 宽） 供应商设备封装:20-SOIC W 包装:管件 |
| ISL84684IR-T | 功能描述:IC SWITCH DUAL SPDT 10TDFN RoHS:否 类别:集成电路 (IC) >> 接口 - 模拟开关，多路复用器，多路分解器 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:- 电路:2 x SPST 导通状态电阻:20 欧姆 电压电源:单电源 电压 - 电源，单路/双路(±):3 V ~ 5.5 V 电流 - 电源:4.1mA 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-WFDFN 裸露焊盘 供应商设备封装:10-TDFN-EP（3x3） 包装:带卷 (TR) |
| ISL84684IRZ | 功能描述:IC SWITCH DUAL SPDT 10TDFN RoHS:是 类别:集成电路 (IC) >> 接口 - 模拟开关，多路复用器，多路分解器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:36 系列:- 功能:多路复用器 电路:2 x 4:1 导通状态电阻:75 欧姆 电压电源:单/双电源 电压 - 电源，单路/双路(±):2 V ~ 12 V，±2 V ~ 6 V 电流 - 电源:- 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:20-SOIC（0.295"，7.50mm 宽） 供应商设备封装:20-SOIC W 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。