- 您现在的位置：买卖IC网 > PDF目录14588 > ISL8540IVEZ (Intersil)IC REG BUCK SYNC ADJ 2A 20HTSSOP PDF资料下载
参数资料
| 型号： | ISL8540IVEZ |
| 厂商： | Intersil |
| 文件页数： | 4/16页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK SYNC ADJ 2A 20HTSSOP |
| 标准包装： | 74 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 1.21 V ~ 35 V |
| 输入电压： | 9 V ~ 40 V |
| PWM 型： | 电压模式 |
| 频率 - 开关： | 100kHz ~ 600kHz |
| 电流 - 输出： | 2A |
| 同步整流器： | 是 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-TSSOP（0.173"，4.40mm 宽）裸露焊盘 |
| 包装： | 管件 |
| 供应商设备封装： | 20-TSSOP-EP |
| 产品目录页面： | 1248 (CN2011-ZH PDF) |
ISL8540
Electrical Specifications
Unless otherwise specified the specifications listed in the table are tested at T A = +25°C and guard band for the
full Temperature Range, V IN = 24V, V OUT = 5.0V, I OUT = 0A. Typical values are at T A = +25°C. Parameters
with MIN and/or MAX limits are 100% tested at +25°C, unless otherwise specified. Temperature limits
established by characterization and are not production tested. (Continued)
PARAMETER
SYMBOL
TEST CONDITIONS
MIN
TYP
MAX
UNITS
THERMAL SHUT-DOWN
Thermal Shut-down Temperature
Thermal Shut-down Hysteresis
Rising Threshold
150
15
°C
°C
Pin Descriptions
VIN (Pins 1, 2, 19, 20)
The input supply for the PWM regulator power stage.
Connected to DRAIN of the high side MOSFET.
LX (Pins 3, 4, 17, 18)
There are four output pins that must be connected together
externally in normal operation.
BOOT (Pin 5)
A capacitor is connected from this pin to the output pin. An
internal 10V supply and an internal Schottky diode provide
the high side voltage to drive the gate of the internal DMOS
device.
EN (Pin 6)
The EN input will disable the part and shut-down all function
when it is held high or left OPEN. The EN current will be
10μA typical. An internal pull-up resistor will hold the pin
high. When EN = Low, the part is enabled. Connect to GND
for auto start-up.
VCC5 (Pin 7)
VCC5 is the +5.0V output pin which provides an output of an
internal supply for supply filtering purposes. A 1μF capacitor
should be connected from this pin to GND. Internal VDD
supply is set at 5.0V (not planned that the user would use
this supply).
SYNC (Pin 8)
This pin provides a digital input pin to synchronize the
internal oscillator to an external signal. When the sync
function is not used, this pin can be left open or tied to GND.
If the sync function is used, the RTCT timing must be set to a
frequency lower than the sync input frequency. The
termination of the ramp is synchronized with the rising edge
of the sync input signal. There are no duty cycle restrictions
on the input sync signal. Input thresholds are TTL
compatible.
4
RTCT (Pin 9)
A resistor to VIN and a capacitor to GND determine the
frequency of the saw-tooth oscillator. Resistor range is
R = 20k to 100k. Capacitor range is C = 470pF to 1.2nF. The
oscillator amplitude will vary from approximately 0.9V to 10V
as V IN changes from 8.5V to 40V to maintain constant
frequency and provide feed forward. The oscillator will have
a fixed off time, which will establish the maximum on time for
the regulator. This off time will be <200ns. The maximum
duty cycle for a 500kHz system will therefore be
approximately 90%, as the frequency of the maximum duty
cycle will increase (95% for 250kHz system). The minimum
duty cycle is zero.
SGND (Pin 10)
The SGND terminal of the ISL8540 provides the return path
for the control and monitor portions of the IC.
FB (Pin 11)
This is the feedback pin. The feedback ratio is set by an
external resistor divider connected to the load.
COMP (Pin 12)
This pin is connected to the output of the Error Amplifier and
is used to compensate the loop. The Error Amplifier is a GM
amplifier.
REF (Pin 13)
1.20V reference output. Bypass to GND with 1μF capacitor.
PGOOD (Pin 14)
This pin is an open drain output that is turned on when the
feedback voltage is more than ±10% from the reference
voltage, indicating that the output is not within 10% of set
point.
PGND (Pin 15)
This pins are used as the ground connection of the power
train.
SS (Pin 16)
A capacitor is connected from this pin to GND to determine
the soft-start timing. The soft-start pin internal charging
current is 10μA.
FN6495.5
September 9, 2008
相关PDF资料 |
PDF描述 |
|---|---|
| MAX6468XS20D7+T | IC MPU/RESET CIRC 2.00V SC70-4 |
| MAX6468XS24D3+T | IC MPU/RESET CIRC 2.400V SC70-4 |
| MAX6467XS23D7+T | IC MPU/RESET CIRC 2.313V SC70-4 |
| 381LQ561M315J052 | CAP ALUM 560UF 315V 20% SNAP |
| 380LX271M450A022 | CAP ALUM 270UF 450V 20% SNAP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL8540IVEZ-T | 功能描述:IC REG BUCK SYNC ADJ 2A 20HTSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:两者兼有 输出数:1 输出电压:5V，1 V ~ 10 V 输入电压:3.5 V ~ 28 V PWM 型:电流模式 频率 - 开关:220kHz ~ 1MHz 电流 - 输出:600mA 同步整流器:无 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:16-SSOP（0.154"，3.90mm 宽） 包装:带卷 (TR) 供应商设备封装:16-QSOP |
| ISL85410FRZ | 制造商:Intersil Corporation 功能描述:36VIN 1A SYNCHRONOUS SWITCHING REGULATOR- 4X3 12LD DFN PB-FR - Rail/Tube 制造商:Intersil Corporation 功能描述:IC REG BUCK SYNC ADJ 1A 12DFN |
| ISL85410FRZ-T | 制造商:Intersil Corporation 功能描述:36VIN 1A SYNCHRONOUS SWITCHING REGULATOR 4X3 12LD DFN T&R - Tape and Reel 制造商:Intersil Corporation 功能描述:IC REG BUCK SYNC ADJ 1A 12DFN |
| ISL85410FRZ-T7A | 制造商:Intersil Corporation 功能描述:IC REG BUCK SYNC ADJ 1A 12DFN |
| ISL85412FRTZ | 制造商:Intersil Corporation 功能描述:36VIN 150MA SYNCHRONOUS SWITCHING REGULATOR- 3X3 8LD TDFN PB - Tape and Reel |
发布紧急采购，3分钟左右您将得到回复。