- 您现在的位置：买卖IC网 > PDF目录20070 > ISL9003AIRURZ-T (Intersil)IC REG LDO 2.6V .15A 6-TDFN PDF资料下载
参数资料
| 型号： | ISL9003AIRURZ-T |
| 厂商： | Intersil |
| 文件页数： | 9/12页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO 2.6V .15A 6-TDFN |
| 标准包装： | 3,000 |
| 稳压器拓扑结构： | 正，固定式 |
| 输出电压： | 2.6V |
| 输入电压： | 最高 6.5V |
| 电压 - 压降（标准）： | 0.25V @ 300mA |
| 稳压器数量： | 1 |
| 电流 - 输出： | 150mA（最小） |
| 电流 - 限制（最小）： | 175mA |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 6-UFDFN 裸露焊盘 |
| 供应商设备封装： | 6-UTDFN（1.6x1.6） |
| 包装： | 带卷 (TR) |
ISL9003A
Block Diagram
V IN
V O
GND
UVLO
CONTROL
LOGIC
SHORT CIRCUIT,
THERMAL PROTECTION,
SOFT-START
+
-
SD
BANDGAP AND
TEMPERATURE
SENSOR
VOLTAGE AND
REFERENCE
GENERATOR
1.0V
0.94V
0.9V
GND
CBYP
Functional Description
The ISL9003A contains all circuitry required to implement a
high performance LDO. High performance is achieved
through a circuit that delivers fast transient response to
varying load conditions. In a quiescent condition, the
ISL9003A adjusts its biasing to achieve the lowest standby
current consumption.
The device also integrates current limit protection, smart
thermal shutdown protection, and soft-start. Smart Thermal
shutdown protects the device against overheating. Soft-start
minimizes start-up input current surges without causing
excessive device turn-on time.
Power Control
The ISL9003A has an enable pin, (EN), to control power to
the LDO output. When EN is low, the device is in shutdown
mode. In this condition, all on-chip circuits are off, and the
device draws minimum current, typically less than 0.3 μ A.
When the EN pin goes high, the device first polls the output
of the UVLO detector to ensure that VIN voltage is at least
2.1V (typical). Once verified, the device initiates a start-up
sequence. During the start-up sequence, trim settings are
first read and latched. Then, sequentially, the bandgap,
reference voltage and current generation circuitry turn-on.
Once the references are stable, the LDO powers-up.
During operation, whenever the VIN voltage drops below
about 1.84V, the ISL9003A immediately disables the LDO
output. When VIN rises back above 2.1V (assuming the EN
pin is high), the device re-initiates its start-up sequence and
LDO operation resumes automatically.
9
Reference Generation
The reference generation circuitry includes a trimmed
bandgap, a trimmed voltage reference divider, a trimmed
current reference generator, and an RC noise filter. The filter
includes the external capacitor connected to the CBYP pin.
A 0.01 μ F capacitor connected CBYP implements a 100Hz
lowpass filter, and is recommended for most high
performance applications. For the lowest noise application, a
0.1 μ F or greater CBYP capacitor should be used. This filters
the reference noise to below the 10Hz to 1kHz frequency
band, which is crucial in many noise-sensitive applications.
The bandgap generates a zero temperature coefficient (TC)
voltage for the regulator reference and other voltage
references required for current generation and
over-temperature detection.
A current generator provides references required for
adaptive biasing as well as references for LDO output
current limit and thermal shutdown determination.
LDO Regulation and Programmable Output Divider
The LDO Regulator is implemented with a high-gain
operational amplifier driving a PMOS pass transistor. The
design of the ISL9003A provides a regulator that has low
quiescent current, fast transient response, and overall
stability across all operating and load current conditions.
LDO stability is guaranteed for a 1μF to 4.7μF output
capacitor that has a tolerance better than 20% and ESR less
than 200m Ω . The design is performance-optimized for a 1μF
capacitor. Unless limited by the application, use of an output
capacitor value above 4.7μF is not recommended as LDO
performance improvement is minimal. Soft-start circuitry
integrated into each LDO limits the initial ramp-up rate to
FN6299.4
October 1, 2009
相关PDF资料 |
PDF描述 |
|---|---|
| MIC3002GML | IC LASER DRIVR 10GBPS 3.6V 24MLF |
| ISL9003AIRUNZ-T | IC REG LDO 3.3V .15A 6-UTDFN |
| AGM24DRMD | CONN EDGECARD 48POS .156 WW |
| R2D10-1515 | CONV DC/DC 2W +/-15VOUT SMD |
| ISL9014AIRFDZ-T | IC REG LDO 2.5V/2V .3A 10-DFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL9003IEBZ-T | 制造商:Intersil Corporation 功能描述:PB-FREE W/ANNEAL SINGLE LOW NOISE HIGH PSRR LDO, 1.50V, SC-7 - Tape and Reel 制造商:Intersil Corporation 功能描述:IC REG LDO 1.5V 0.15A SC70-5 制造商:Intersil 功能描述:W/ANNEAL SINGLE LW NOISE IQHI PSRR 1 5V |
| ISL9003IECZ | 制造商:Intersil Corporation 功能描述: |
| ISL9003IECZ-T | 制造商:Intersil Corporation 功能描述:PB-FREE W/ANNEAL SINGLE LOW NOISE HIGH PSRR LDO, 1.80V, SC-7 - Tape and Reel 制造商:Intersil Corporation 功能描述:IC REG LDO 1.8V 0.15A SC70-5 制造商:Intersil 功能描述:W/ANNEAL SINGLE LW NOISE IQHI PSRR 1 5V |
| ISL9003IEFZ-T | 制造商:Intersil Corporation 功能描述:PB-FREE W/ANNEAL SINGLE LOW NOISE HIGH PSRR LDO, 2.50V, SC-7 - Tape and Reel 制造商:Rochester Electronics LLC 功能描述: 制造商:Intersil Corporation 功能描述:IC REG LDO 2.5V 0.15A SC70-5 制造商:Intersil Corporation 功能描述:Voltage Regulators - Standard W/ANNEAL SINGLE LW NOISE HI 50V SC-7 |
| ISL9003IEHZ-T | 制造商:Intersil Corporation 功能描述:PB-FREE W/ANNEAL SINGLE LOW NOISE HIGH PSRR LDO, 2.75V, SC-7 - Tape and Reel 制造商:Intersil Corporation 功能描述:IC REG LDO 2.75V 0.15A SC70-5 制造商:Intersil 功能描述:W/ANNEAL SINGLE LW NOISE HI 2 75V SC-7 |
发布紧急采购，3分钟左右您将得到回复。