参数资料
| 型号： | ISL90840WIV2027ZT2 |
| 厂商： | Intersil |
| 文件页数： | 4/13页 |
| 文件大小： | 0K |
| 描述： | IC XDCP 256-TAP 10KOHM TSSOP-20 |
| 标准包装： | 2,500 |
| 系列： | XDCP™ |
| 接片： | 256 |
| 电阻（欧姆）： | 10k |
| 电路数： | 4 |
| 温度系数： | 标准值 ±45 ppm/°C |
| 存储器类型： | 易失 |
| 接口： | I²C（设备位址） |
| 电源电压： | 2.7 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 20-TSSOP |
| 包装： | 带卷 (TR) |
12
FN8086.2
November 14, 2006
Write Operation
A Write operation requires a START condition, followed by a
valid Identification Byte, a valid Address Byte, a Data Byte,
and a STOP condition. After each of the three bytes, the
ISL90840 responds with an ACK. At this time, the device
enters its standby state (See Figure 17).
Read Operation
A Read operation consist of a three byte instruction followed
by one or more Data Bytes (See Figure 18). The master
initiates the operation issuing the following sequence: a
START, the Identification byte with the R/W bit set to “0”, an
Address Byte, a second START, and a second Identification
byte with the R/W bit set to “1”. After each of the three bytes,
the ISL90840 responds with an ACK. Then the ISL90840
transmits Data Bytes as long as the master responds with an
ACK during the SCL cycle following the eighth bit of each
byte. The master terminates the read operation (issuing a
ACK and STOP condition) following the last bit of the last
Data Byte (See Figure 18).
The Data Bytes are from the registers indicated by an
internal pointer. This pointer initial value is determined by the
Address Byte in the Read operation instruction, and
increments by one during transmission of each Data Byte.
After reaching the memory location 03h, the pointer “rolls
over” to 00h, and the device continues to output data for
each ACK received.
S
T
A
R
T
S
T
O
P
IDENTIFICATION
BYTE
ADDRESS
BYTE
DATA
BYTE
A
C
K
SIGNALS FROM
THE MASTER
SIGNALS FROM
THE ISL90840
A
C
K
0
11
A
C
K
WRITE
SIGNAL AT SDA
00 0 0
A0
A1
A2
00
FIGURE 17. BYTE WRITE SEQUENCE
SIGNALS
FROM THE
MASTER
SIGNALS FROM
THE SLAVE
SIGNAL AT SDA
S
T
A
R
T
IDENTIFICATION
BYTE WITH
R/W=0
ADDRESS
BYTE
A
C
K
A
C
K
00
0
11
S
T
O
P
A
C
K
0
1
0
11
IDENTIFICATION
BYTE WITH
R/W=1
A
C
K
S
T
A
R
T
LAST READ
DATA BYTE
FIRST READ
DATA BYTE
A
C
K
0
00 0
0 0
A0
A1
A2
A0
A1
A2
FIGURE 18. READ SEQUENCE
A
C
K
ISL90840
相关PDF资料 |
PDF描述 |
|---|---|
| ISL90841WIV1427Z | IC XDCP 256-TAP 10KOHM TSSOP-14 |
| ISL90842UIV1427Z | IC DCP 256-TAP 50KOHM TSSOP-14 |
| ISL90843UIU1027Z-TK | IC XDCP 256-TAP 50OHM 10-MSOP |
| ISL95310WIU10Z | IC XDCP 128-TAP 10KOHM 10-MSOP |
| ISL95311WIU10Z | IC XDCP 128-TAP 10KOHM 10-MSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL90841 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Low Noise, Low Power I2C Bus, 256 Taps |
| ISL90841_06 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Quad Digitally Controlled Potentiometers (XDCP⑩) |
| ISL90841UIV1427 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Low Noise, Low Power I2C Bus, 256 Taps |
| ISL90841UIV1427Z | 功能描述:IC XDCP 256-TAP 50KOHM TSSOP-14 RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数字电位器 系列:XDCP™ 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 接片:256 电阻（欧姆）:100k 电路数:2 温度系数:标准值 35 ppm/°C 存储器类型:易失 接口:6 线串行（芯片选择，递增，增/减） 电源电压:2.6 V ~ 5.5 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:14-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:14-TSSOP 包装:带卷 (TR) |
| ISL90841UIV1427Z-TK | 功能描述:IC POT DGTL QUAD 50K OHM 14TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数字电位器 系列:XDCP™ 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 接片:256 电阻（欧姆）:100k 电路数:2 温度系数:标准值 35 ppm/°C 存储器类型:易失 接口:6 线串行（芯片选择，递增，增/减） 电源电压:2.6 V ~ 5.5 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:14-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:14-TSSOP 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。