- 您现在的位置：买卖IC网 > PDF目录20777 > ISL97635IRZ-T (Intersil)IC LED DRVR WHT/RGB BCKLGT 24QFN PDF资料下载
参数资料
| 型号： | ISL97635IRZ-T |
| 厂商： | Intersil |
| 文件页数： | 13/28页 |
| 文件大小： | 0K |
| 描述： | IC LED DRVR WHT/RGB BCKLGT 24QFN |
| 标准包装： | 6,000 |
| 拓扑： | PWM，升压（升压） |
| 输出数： | 8 |
| 内部驱动器： | 是 |
| 类型 - 主要： | 车载，背光 |
| 类型 - 次要： | RGB，白色 LED |
| 频率： | 600kHz，1.2MHz |
| 电源电压： | 6 V ~ 24 V |
| 输出电压： | 34.5V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-VFQFN 裸露焊盘 |
| 供应商设备封装： | 24-QFN 裸露焊盘（4x4） |
| 包装： | 带卷 (TR) |
| 工作温度： | -40°C ~ 85°C |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页当前第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
ISL97635
PWMO pin for DPST mode operation which will be described
in “PWM Dimming Frequency Adjustment” on page 13.
C PWMO should be significantly larger than the external PWMI
period, t, such that Equation 13 will show:
For example, if the SMBus controlled PWM duty is 80%
40k Ω x C PWMO >t
(EQ. 13)
dimming at 200Hz (see C FPWM Equation 12) and the
external PWMI duty cycle is 60% dimming at 1kHz, the
resultant PWM duty cycle is 48% dimming at 200Hz.
Method 4 (Analog Mode, DC-to-PWM Mode)
By overdriving the PWMO pin with a DC voltage between
0.21V and 1.21V, the average LED current of each channel
is controlled by the internally generated PWM signal, as
shown in Equation 11:
For example, if F PWM is 200Hz and an external PWMI is
1kHz and above, a 220nF C PWMO can be chosen that allows
the external PWMI signal to be filtered as an averaged DC.
Also, the F PWM frequency in the DPST mode should be
limited between 100Hz to 2kHz and at least five times
smaller than the external PWMI frequency when DPST
mode is used.
Switching Frequency
I LED ( ave ) = I LED × BRT ? 255 × ( 1 – ( V ( PWMO ) – 0.21 ) )
(EQ. 11)
An internal clock of 1.2MHz is used for the boost regulator
control of the LX pin in default. There are 2 levels of
Where BRT is the value held in Register 0x00 (default
setting 0xFF). The PWMO pin is internally driven to 0.21V
via a 40k Ω resistor when the EN/PWMI pin is in logic high,
any overdrive circuit will need to be able to drive up to 40μA
in order to overcome this.
The DC-to-PWM controlled PWM frequency is adjusted by a
capacitor at the FPWM pin, which will be described in “PWM
Dimming Frequency Adjustment” on page 13.
For example, if PWMO is applied with a DC voltage ≥ 1.21V,
the output will be zero. On the other hand, if the PWMO is
applied with a DC voltage ≤ 0.21V, the PWM duty cycle will
be at its maximum. If the PWMO pin is applied with a DC
voltage of 0.31V, the PWM duty cycle will be at 90% at
200Hz if C FPWM = 27nF.
PWM Dimming Frequency Adjustment
(Applicable to SMBus controlled PWM, DPST, and
DC-to-PWM Modes)
Except for the external PWM dimming mode where the
frequency follows the external signals, the dimming
frequencies of the other modes are set by an external
capacitor C FPWM at the FPWM pin, as shown in Equation 12:
switching frequencies: 600kHz or 1.2MHz. Each can be
programmed in the Configuration Register 0x08 bit 2. The
default switching frequency is at 1.2MHz.
5V Low Dropout Regulator
A 5.2V LDO regulator is present at the VDC pin to develop the
necessary low voltage supply, which is used by the chips
internal control circuitry. Because VDC is an LDO pin, it
requires a bypass capacitor of 1μF or more for the regulation.
For applications with an input voltage ≤ 5.5V, VIN and VDC
pins can be connected together. Low input voltage also allows
only lower output voltage applications only with the maximum
boost ratio defined in “Components Selections” on page 24.
The VDC pin can be used as a coarse reference with a few
mA sourcing capability.
In-rush Control and Soft-start
The ISL97635 has separately built-in independent inrush
control and soft-start functions. The inrush control function is
built around the short circuit protection FET, and is only
available in applications, which include this device. At
start-up, the fault protection FET is turned on slowly due to a
30μA pull-down current output from the FAULT pin. This
discharges the fault FET's gate-source capacitance, turning
C FPWM = 5.4 μ F ? FPWM
(EQ. 12)
on the FET in a controlled fashion. As this happens, the
output capacitor is charged slowly through the weakly turned
where FPWM is the desirable PWM dimming frequency.
For example, if FPWM = 200Hz, C FPWM = 5.4μF/200 = 27nF
The PWM dimming frequency can be for example 20kHz but
there are a minimum on and off time requirements such that
the dimming will be in the range of 10% to 99.5%. If the
dimming frequency is below 5kHz, the dimming range can
be 1% to 99.5%.
In the DPST and DC-to-PWM modes, a C PWMO capacitor is
also needed. An internal 40k Ω and an external C PWMO at the
PWMO pin form a low pass network to filter the PWMI to an
averaged DC. As a result, the time constant of the 40k Ω and
13
on FET before it becomes fully enhanced. This results in a
low in-rush current. This current can be further reduced by
adding a capacitor (in the 1nF to 5nF range) across the
gate-source terminals of the FET.
Once the chip detects that the fault protection FET is turned
on hard, it is assumed that in-rush has completed. At this
point, the boost regulator will begin to switch and the current
in the inductor will ramp-up. The current in the boost power
switch is monitored and the switching is terminated in any
cycle where the current exceeds the current limit. The
ISL97635 includes a soft-start feature where this current limit
starts at a low value (375mA). This is stepped up to the final
3A current limit in 7 further steps of 375mA. These steps will
happen over a 1ms total time, such that after 1ms, the final
limit will be reached. This allows the output capacitor to be
FN6434.2
December 22, 2008
相关PDF资料 |
PDF描述 |
|---|---|
| 1N5817-B | DIODE SCHOTTKY 20V 1A DO-41 |
| TAP227M006CCS | CAP TANT 220UF 6.3V 20% RADIAL |
| TH3A685K016E2000 | CAP TANT 6.8UF 16V 10% 1206 |
| TH3A685K016C2000 | CAP TANT 6.8UF 16V 10% 1206 |
| TH3B225M025E3000 | CAP TANT 2.2UF 25V 20% 1411 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL97635IRZ-TK | 功能描述:IC LED DRVR WHT/RGB BCKLGT 24QFN RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 恒定电流:- 恒定电压:- 拓扑:升压（升压），切换式电容器（充电泵） 输出数:1 内部驱动器:是 类型 - 主要:背光 类型 - 次要:白色 LED 频率:625kHz ~ 875kHz 电源电压:2.7 V ~ 5.3 V 输出电压:5V 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-µMAX 包装:带卷 (TR) 工作温度:-40°C ~ 85°C |
| ISL97636AIRZ | 功能描述:LED照明驱动器 6-CH LED DRVR RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| ISL97636AIRZ-T | 功能描述:IC LED DRIVR WHITE BCKLGT 24-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 恒定电流:- 恒定电压:- 拓扑:升压（升压），切换式电容器（充电泵） 输出数:1 内部驱动器:是 类型 - 主要:背光 类型 - 次要:白色 LED 频率:625kHz ~ 875kHz 电源电压:2.7 V ~ 5.3 V 输出电压:5V 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-µMAX 包装:带卷 (TR) 工作温度:-40°C ~ 85°C |
| ISL97636AIRZ-TK | 功能描述:IC LED DRIVR WHITE BCKLGT 24-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 恒定电流:- 恒定电压:- 拓扑:升压（升压），切换式电容器（充电泵） 输出数:1 内部驱动器:是 类型 - 主要:背光 类型 - 次要:白色 LED 频率:625kHz ~ 875kHz 电源电压:2.7 V ~ 5.3 V 输出电压:5V 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-µMAX 包装:带卷 (TR) 工作温度:-40°C ~ 85°C |
| ISL97636IRZ | 功能描述:IC LED DRIVR WHITE BCKLGT 24-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 标准包装:6,000 系列:- 恒定电流:- 恒定电压:- 拓扑:开路漏极，PWM 输出数:4 内部驱动器:是 类型 - 主要:LED 闪烁器 类型 - 次要:- 频率:400kHz 电源电压:2.3 V ~ 5.5 V 输出电压:- 安装类型:表面贴装 封装/外壳:8-VFDFN 裸露焊盘 供应商设备封装:8-HVSON 包装:带卷 (TR) 工作温度:-40°C ~ 85°C 其它名称:935286881118PCA9553TK/02-TPCA9553TK/02-T-ND |
发布紧急采购，3分钟左右您将得到回复。