- 您现在的位置：买卖IC网 > PDF目录67723 > ISP1583ET2 (NXP SEMICONDUCTORS) UNIVERSAL SERIAL BUS CONTROLLER, PBGA64 PDF资料下载
参数资料
| 型号： | ISP1583ET2 |
| 厂商： | NXP SEMICONDUCTORS |
| 元件分类： | 总线控制器 |
| 英文描述： | UNIVERSAL SERIAL BUS CONTROLLER, PBGA64 |
| 封装： | 6 X 6 MM, 0.80 MM HEIGHT, LEAD FREE, PLASTIC, MO-195, SOT543-1,TFBGA-64 |
| 文件页数： | 8/100页 |
| 文件大小： | 508K |
| 代理商： | ISP1583ET2 |
第1页第2页第3页第4页第5页第6页第7页当前第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页
ISP1583_7
NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 07 — 22 September 2008
14 of 99
NXP Semiconductors
ISP1583
Hi-Speed USB peripheral controller
8.2 Hi-Speed USB transceiver
The analog transceiver directly interfaces to the USB cable through integrated termination
resistors. The high-speed transceiver requires an external resistor (12.0 k
± 1%)
between pin RREF and ground to ensure an accurate current mirror that generates the
Hi-Speed USB current drive. A full-speed transceiver is integrated as well. This makes the
ISP1583 compliant to Hi-Speed USB and Original USB, supporting both the high-speed
and full-speed physical layers. After automatic speed detection, the NXP Serial Interface
Engine (SIE) sets the transceiver to use either high-speed or full-speed signaling.
8.3 MMU and integrated RAM
The Memory Management Unit (MMU) manages the access to the integrated RAM that is
shared by the USB, microcontroller handler and DMA handler. Data from the USB bus is
stored in the integrated RAM, which is cleared only when the microcontroller has read the
corresponding endpoint, or the DMA controller has written all data from the RAM of the
corresponding endpoint to the DMA bus. The OUT endpoint buffer can also be forcibly
cleared by setting bit CLBUF in the Control Function register. A total of 8 kB RAM is
available for buffering.
8.4 Microcontroller interface and microcontroller handler
The microcontroller interface allows direct interfacing to most microcontrollers and
microprocessors. The interface is congured at power-up through pins BUS_CONF/DA0,
MODE1 and MODE0/DA1.
When pin BUS_CONF/DA0 = HIGH, the microcontroller interface switches to generic
processor mode in which AD[7:0] is the 8-bit address bus and DATA[15:0] is the separate
16-bit data bus. If pin BUS_CONF/DA0 = LOW, the interface is in split bus mode, where
AD[7:0] is the local microprocessor bus (multiplexed address and data) and DATA[15:0] is
solely used as the DMA bus.
When pin MODE0/DA1 = HIGH, pins RW_N/RD_N and DS_N/WR_N are the read and
write strobes (8051 mode). If pin MODE0/DA1 = LOW, pins RW_N/RD_N and
DS_N/WR_N represent the direction and data strobes (Freescale mode).
When pin MODE1 = LOW, pin ALE/A0 is used to latch the multiplexed address on pins
AD[7:0]. When pin MODE1 = HIGH, pin ALE/A0 is used to indicate address or data. Pin
MODE1 is only used in split bus mode; in generic processor mode, it must be tied to
VCC(I/O).
The microcontroller handler allows the external microcontroller to access the register set
in the NXP SIE, as well as the DMA handler. The initialization of the DMA conguration is
done through the microcontroller handler.
8.5 OTG SRP module
The OTG supplement denes a Session Request Protocol (SRP), which allows a B-device
to request the A-device to turn on VBUS and start a session. This protocol allows the
A-device, which may be battery-powered, to conserve power by turning off VBUS when
there is no bus activity while still providing a means for the B-device to initiate bus activity.
Any A-device, including a PC or laptop, can respond to SRP. Any B-device, including a
standard USB peripheral, can initiate SRP.
相关PDF资料 |
PDF描述 |
|---|---|
| ISP1761ET,518 | UNIVERSAL SERIAL BUS CONTROLLER, PBGA128 |
| ISP1761BE,518 | UNIVERSAL SERIAL BUS CONTROLLER, PQFP128 |
| ISP1761BE,551 | UNIVERSAL SERIAL BUS CONTROLLER, PQFP128 |
| ISP1761BE,518 | UNIVERSAL SERIAL BUS CONTROLLER, PQFP128 |
| ITR8307 | SPECIALTY OPTOELECTRONIC DEVICE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISP1583ET2,518 | 功能描述:外围驱动器与原件 - PCI USB 2.0 DEVICE RoHS:否 制造商:PLX Technology 工作电源电压: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:FCBGA-1156 封装:Tray |
| ISP1583ET2-T | 功能描述:外围驱动器与原件 - PCI USB 2.0 DEVICE RoHS:否 制造商:PLX Technology 工作电源电压: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:FCBGA-1156 封装:Tray |
| ISP1583ET-T | 功能描述:外围驱动器与原件 - PCI HI-SPEED USB2 DEVICE RoHS:否 制造商:PLX Technology 工作电源电压: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:FCBGA-1156 封装:Tray |
| ISP1583ETUM | 功能描述:IC USB CTRL HI-SPEED 64TFBGA RoHS:是 类别:集成电路 (IC) >> 接口 - 控制器 系列:- 标准包装:4,900 系列:- 控制器类型:USB 2.0 控制器 接口:串行 电源电压:3 V ~ 3.6 V 电流 - 电源:135mA 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:36-VFQFN 裸露焊盘 供应商设备封装:36-QFN（6x6） 包装:* 其它名称:Q6396337A |
| ISP166 | 功能描述:机架和机柜配件 PANELS 1600HX600D RoHS:否 制造商:Bivar 产品:Rack Accessories 面板空间: 颜色:Black |
发布紧急采购，3分钟左右您将得到回复。