收藏本站
参数资料
型号： ISPNANO S3 KIT
厂商： Equinox Technologies
文件页数： 128/134页
文件大小： 0K
描述： ISP PORTABLE PROGRAMMER
标准包装： 1
类型： 便携式 ISP
适用于相关产品： ATMEL AT90S、AT90CAN、AT90USB、ATtiny、ATmega、AT91SAM7xx、Zensys Z-Wave、24xxx 系列 EEPROM
所含物品： 编程器，线缆，电源
其它名称： 483-1022
ISPNANO S3 KIT-ND
Q5595084
T1310537
# Function
Further information
1 Line Driver / Target Vcc Voltage setup
2 ‘Programmer controlled Target
?
?
?
Sets up the voltage of the programmer I/O signal lines
ie. SPI, JTAG. PDI, TPI lines.
This voltage should be set so it is the same as the
voltage at which the Target IC is powered at.
These are the controls for the ‘Programmer
Power supply’ setup
?
controlled Target Power supply’ .
This power supply should only be enabled if the
programmer is to power the Target System (UUT).
3 External Target Vcc Switch controls
?
These controls supporting switching of the ‘EXT-VCC’
supply which in turn switches the relay coils ON /
OFF.
4.3 Setting the Programmer Signal Line Driver voltage
The ‘Programmer Signal – Line Driver Voltage’ is the voltage level of logic ‘1’ signal on any of the
programmer I/O pins.
Please note:
?
?
This voltage should usually be set to the same voltage that the Target IC is actually running at.
If the programmer is NOT powering the Target System but you still wish to measure / validate
the Target Voltage, tick the ‘Check Target Voltage’ box.
4.4 ‘Programmer controlled Target Power supply’ setup
The ‘Programmer controlled Target Power supply’ is a fully programmable power supply which
can be used to power the Target System. It is capable of generating any voltage from 1.2 to 5.0V @
300mA.
?
?
?
?
Please see section 4.0 of the main User Manual for full details of how to set up this power
supply.
This power supply is routed through a relay to the ‘TVCC (Target Vcc)’ pin of the ‘Target ISP
Port’ so it is DISCONNECTED from the Target System until the RELAYs are switched ON.
When powering up the Target System using this power supply, the programmer will
automatically switch the relays coils ON, wait for 50ms for the contacts to switch properly
(debounce delay) and then switch the ‘Programmer controlled Target Power supply’ ON.
This debounce delay helps to extend the life of the relay contacts by not switching the contacts
when the power is on.
The ‘PSU_OUT_DELAY’ is the overall time allowed for the power supply voltage and current
to settle. This parameter should always be set to at least 10ms greater than the ‘Voltage Settle
time’ and ‘Current Settle time’.
Please note:
ISPnano Series Programmer - User Manual – V1.11 – 12 May 2011
112
th
相关PDF资料
PDF描述
IX2127N IC HIGH SIDE DRIVER 8SOIC
IX2R11S3T/R IC DRVR HALF BRIDGE 2A 16-SOIC
IX4R11S3T/R IC DRVR HALF BRIDGE 4A 16-SOIC
IX6R11S6T/R IC DRVR HALF BRIDGE 4A 18-SOIC
IXA531S10T/R IC BRIDGE DRVR 3PH 500MA 48-MLP
相关代理商/技术参数
参数描述
ISPNANO-UPG10AR 功能描述:ISP NANO RUN TIME LICENSE RoHS:否 类别:编程器，开发系统 >> 知识产权 (IP) 系列:* 标准包装:1 系列:Nios®II 类型:Nios II 功能:C 到硬件编译器 许可证:初始许可证
ISPNANO-UPG18 功能描述:ISP PORTABLE PROGRAMMER USB RoHS:是 类别:编程器，开发系统 >> 软件 系列:* 标准包装:1 系列:ISE® 设计套件 类型:订阅 适用于相关产品:Xilinx FPGAs 其它名称:Q4986209T1081384
ISPNANO-UPG7 功能描述:JTAG ISP UPGRADE FOR ATMEL AVR RoHS:否 类别:编程器，开发系统 >> 知识产权 (IP) 系列:* 标准包装:1 系列:Nios®II 类型:Nios II 功能:C 到硬件编译器 许可证:初始许可证
ISPN-UPG10M 功能描述:ISP PORTABLE PROGRAMMER USB RoHS:是 类别:编程器，开发系统 >> 软件 系列:- 标准包装:1 系列:ISE® 设计套件 类型:订阅 适用于相关产品:Xilinx FPGAs 其它名称:Q4986209T1081384
ISPPAC10 制造商:LATTICE 制造商全称:Lattice Semiconductor 功能描述:In-System Programmable Analog Circuit
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*