- 您现在的位置：买卖IC网 > PDF目录16239 > KS8721SL-EVAL (Micrel Inc)BOARD EVAL EXPERIMENT KS8721SL PDF资料下载
参数资料
| 型号： | KS8721SL-EVAL |
| 厂商： | Micrel Inc |
| 文件页数： | 8/33页 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL EXPERIMENT KS8721SL |
| 标准包装： | 1 |
| 主要目的： | 接口，以太网控制器（PHY 和 MAC） |
| 嵌入式： | 否 |
| 已用 IC / 零件： | KSZ8721SL |
| 主要属性： | 1 个端口，100BASE-TX/100BASE-FX/10BASE-T |
| 次要属性： | MII，RMII，自动 MDI，MDIX，>130 米线缆驱动器，LDO，符合 IEEE802.3u 要求 |
| 已供物品： | 板 |
| 相关产品： | KS8721SLA4 TR-ND - TXRX 10/100 3.3V 48-SSOP KS8721SLA4-ND - TXRX 10/100 3.3V 48-SSOP KS8721SL-ND - TXRX 10/100 3.3V 48-SSOP KS8721SLI-ND - IC TXRX PHY 10/100 3.3V 48SSOP KS8721SL TR-ND - IC TXRX PHY 10/100 3.3V 48SSOP |
| 其它名称： | 576-1010 |
第1页第2页第3页第4页第5页第6页第7页当前第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页
KS8721BL/SL
Micrel
M9999-051704
16
May 2004
Power Management
The KS8721BL/SL offers the following modes for power management:
Power-Down Mode: This mode can be achieved by writing to Register 0.11 or pulling pin 30 PD# low.
Power-Saving Mode: This mode can be disabled by writing to Register 1fh.10. The KS8721BL/SL turns off
everything except for the Energy Detect and PLL circuits when the cable is not installed. In other words, the
KS8721BL/SL shuts down most of the internal circuits to save power if there is no link. Power-saving mode is in the
most effective state when auto-negotiation mode is enabled.
100BT FX Mode
Please contact your local field application engineer (FAE) for a reference schematic on fiber connection.
100BT FX mode is activated when FXSD/FXEN is higher than 0.6V (this pin has a default pull down). Under this mode, the
auto-negotiation and auto-MDI-X features are disabled.
In fiber operation, the FXSD pin should connect to the signal detect (SD) output of the fiber module. The internal threshold of
FXSD is around 1/2 V
DD ±50mV (1.25V ±0.05V). Above this level, the fiber signal is considered detected. The operation is
summarized in the following table:
FXSD/FXEN
Condition
Less than 0.6V
100TX mode
Less than 1.25V,
FX mode
but greater than 0.6V
No signal detected
FEF generated
Greater than 1.25
FX mode
Signal detected
Table 1. 100BT FX Mode
To ensure proper operation, the swing of fiber module SD should cover the threshold variation. A resistive voltage divider is
recommended to adjust the SD voltage range.
Far End Fault (FEF), repetition of a special pattern which consists of 84-one and 1-zero, is generated under “FX mode with
no signal detected.” The purpose of FEF is to notify the sender of a faulty link. When receiving an FEF, the LINK will go down
to indicate a fault, even with fiber signal detected. The transmitter is not affected by receiving an FEF and still sends out its
normal transmit pattern from MAC. FEF can be disabled by strapping pin 27 low. Refer to the “Strapping Options” section.
Media Converter Operation
The KS8721BL/SL is capable of performing media conversion with two parts in a back-to-back RMII loop-back mode as
indicated in the diagram. Both parts are in RMII mode and with RMII BTB asserted (pins 21 and 22 strapped high). One part
is operating in TX mode and the other is operating in FX mode. Both parts can share a common 50MHz oscillator.
Under this operation, auto-negotiation on the TX side prohibits 10BASE-T link-up. Additional options can be implemented
under this operation. Disable the transmitter and set it at tri-state by controlling the high TXD2 pin. In order to do this, RXD2
and TXD2 pins need to be connected via inverter. When TXD2 pin is high in both the copper and fiber operation, it is disabled
transmit. Meanwhile, the RXD2 pin on the copper side serves as the energy detect and can indicate if a line signal is detected.
TXD3 should be tied low and RXD3 let float. Please contact your Micrel FAE for a media converter reference design.
Figure 3. Fiber Module
Rx +/-
Tx +/-
FTx
FRx
Pin
34
TxD
(Fiber Mode)
21 22
Pin
21 22
50MHz
VCC
OSC
TxC/
Ref_CLK
TxC/
Ref_CLK
RxD
VCC
KS8721BL/SL
KS8721BL/SL
To the SD pin of the
Fiber Module
TxD
相关PDF资料 |
PDF描述 |
|---|---|
| RMM08DTKN | CONN EDGECARD 16POS DIP .156 SLD |
| RMM08DTKH | CONN EDGECARD 16POS DIP .156 SLD |
| DS2762AE+025 | IC MON BATT LI-ION HP 16-TSSOP |
| RMM08DTKD | CONN EDGECARD 16POS DIP .156 SLD |
| H3BWH-6418M | IDC CABLE - HSR64H/AE64M/HPL64H |
相关代理商/技术参数 |
参数描述 |
|---|---|
| KS8721SLI | 功能描述:IC TXRX PHY 10/100 3.3V 48SSOP RoHS:否 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 标准包装:1,140 系列:AU 类型:收发器 驱动器/接收器数:1/1 规程:CAN 电源电压:5.3 V ~ 27 V 安装类型:表面贴装 封装/外壳:14-SOIC（0.154"，3.90mm 宽） 供应商设备封装:14-SO 包装:管件 其它名称:935267940512AU5790D14AU5790D14-ND |
| KS8737 | 制造商:Micrel Inc 功能描述:IC, PHY TRANSCEIVER, 100MBPS, TQFP-64, Data Rate:100Mbps, Ethernet Type:10BASE-T |
| KS8737-EVAL | 功能描述:BOARD EVAL EXPERIMENT FOR KS8737 RoHS:否 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- 主要目的:电源管理，电池充电器 嵌入式:否 已用 IC / 零件:MAX8903A 主要属性:1 芯锂离子电池 次要属性:状态 LED 已供物品:板 |
| KS8761 | 制造商:KENDIN 功能描述: |
| KS8803 | 制造商:SAMSUNG 制造商全称:Samsung semiconductor 功能描述:10/15 CH PLL |
发布紧急采购，3分钟左右您将得到回复。