参数资料
| 型号： | KSZ8051MNL |
| 厂商： | Micrel Inc |
| 文件页数： | 21/59页 |
| 文件大小： | 0K |
| 描述： | TXRX PHY 10/T100 3.3V MII 32-QFN |
| 标准包装： | 640 |
| 类型： | PHY 收发器 |
| 驱动器/接收器数： | 1/1 |
| 规程： | MII |
| 电源电压： | 1.8V，2.5V，3.3V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-VFQFN 裸露焊盘 |
| 供应商设备封装： | 32-QFN（5x5） |
| 包装： | 托盘 |
| 配用： | 576-3865-ND - BOARD EVALUATION FOR KSZ8051MNL |
| 其它名称： | 576-3732 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页当前第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页
Micrel, Inc.
KSZ8051MNL/RNL
July 2010
28
M9999-070910-1.0
RMII Back-to-Back Mode (KSZ8051RNL only)
In RMII Back-to-Back mode, a KSZ8051RNL interfaces with another KSZ8051RNL, or a KSZ8041FTL to provide a
complete 100Mbps copper repeater, or media converter solution, respectively.
The KSZ8051RNL devices are configured to RMII Back-to-Back mode after power-up or reset with the following:
Strapping pin CONFIG[2:0] (pins 18, 29, 28) set to ‘101’
A common 50MHz reference clock connected to XI (pin 9)
RMII signals connected as shown in the following table.
KSZ8051RNL (100Base-TX copper)
[Device 1]
KSZ8051RNL (100Base-TX copper)
[Device 2]
Pin Name
Pin Number
Pin Type
Pin Name
Pin Number
Pin Type
CRSDV
18
Output
TXEN
23
Input
RXD1
15
Output
TXD1
25
Input
RXD0
16
Output
TXD0
24
Input
TXEN
23
Input
CRSDV
18
Output
TXD1
25
Input
RXD1
15
Output
TXD0
24
Input
RXD0
16
Output
Table 4. RMII Signal Connection for RMII Back-to-Back Mode (100Base-TX Copper Repeater)
MII Management (MIIM) Interface
The KSZ8051MNL/RNL supports the IEEE 802.3 MII Management Interface, also known as the Management Data Input /
Output (MDIO) Interface. This interface enables upper-layer device, like a MAC processor, to monitor and control the state
of the KSZ8051MNL/RNL. An external device with MIIM capability is used to read the PHY status and/or configure the
PHY settings. Further details on the MIIM interface can be found in Clause 22.2.4 of the IEEE 802.3 Specification.
The MIIM interface consists of the following:
A physical connection that incorporates the clock line (MDC) and the data line (MDIO).
A specific protocol that operates across the aforementioned physical connection that allows the external controller
to communicate with one or more PHY devices.
A set of 16-bit MDIO registers. Registers [0:8] are standard registers, and their functions are defined per the IEEE
802.3 Specification. The additional registers are provided for expanded functionality. See “Register Map” section
for details.
As the default, the KSZ8051MNL/RNL supports unique PHY addresses 1 to 7, and broadcast PHY address 0. The latter is
defined per the IEEE 802.3 Specification, and can be used to read/write to a single KSZ8051MNL/RNL device, or write to
multiple KSZ8051MNL/RNL devices simultaneously.
Optionally, PHY address 0 can be disabled as the broadcast address by either hardware pin strapping (B-CAST_OFF, pin
19) or software (register 16h, bit 9), and assigned as a unique PHY address.
The PHYAD[2:0] strapping pins are used to assigned a unique PHY address between 0 and 7 to each KSZ8051MNL/RNL
device.
The following table shows the MII Management frame format for the KSZ8051MNL/RNL.
Preamble
Start of
Frame
Read/Write
OP Code
PHY
Address
Bits [4:0]
REG
Address
Bits [4:0]
TA
Data
Bits [15:0]
Idle
Read
32 1’s
01
10
00AAA
RRRRR
Z0
DDDDDDDD_DDDDDDDD
Z
Write
32 1’s
01
00AAA
RRRRR
10
DDDDDDDD_DDDDDDDD
Z
Table 5. MII Management Frame Format – for KSZ8051MNL/RNL
相关PDF资料 |
PDF描述 |
|---|---|
| VE-2V1-MX-F2 | CONVERTER MOD DC/DC 12V 75W |
| SY897132LKY | IC LINK REPLICATOR 28TSSOP |
| SP483CS-L | IC TXRX RS485 HALF DUPLEX 8PDIP |
| MS27497P20F41P | CONN RCPT 41POS WALL MNT W/PINS |
| MS3116P22-21S | CONN PLUG 21POS STRAIGHT W/SCKT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| KSZ8051MNL TR | 功能描述:以太网 IC 3.3V, 10Base-T/100Base-TX Physical Layer Transceiver w/ MII Support (32-QFN) RoHS:否 制造商:Micrel 产品:Ethernet Switches 收发器数量:2 数据速率:10 Mb/s, 100 Mb/s 电源电压-最大:1.25 V, 3.45 V 电源电压-最小:1.15 V, 3.15 V 最大工作温度:+ 85 C 封装 / 箱体:QFN-64 封装:Tray |
| KSZ8051MNL-EVAL | 功能描述:以太网开发工具 3.3V, 10Base-T/100Base-TX Physical Layer Transceiver w/ MII Support (32-QFN) - Evaluation Board RoHS:否 制造商:Micrel 产品:Evaluation Boards 类型:Ethernet Transceivers 工具用于评估:KSZ8873RLL 接口类型:RMII 工作电源电压: |
| KSZ8051MNLI | 功能描述:TXRX PHY 10/T100 3.3V 32QFN RoHS:是 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 标准包装:1,140 系列:AU 类型:收发器 驱动器/接收器数:1/1 规程:CAN 电源电压:5.3 V ~ 27 V 安装类型:表面贴装 封装/外壳:14-SOIC（0.154"，3.90mm 宽） 供应商设备封装:14-SO 包装:管件 其它名称:935267940512AU5790D14AU5790D14-ND |
| KSZ8051MNLI TR | 功能描述:以太网 IC 3.3V, 10Base-T/100Base-TX Physical Layer Transceiver with MII support (32-QFN, Industrial Grade) RoHS:否 制造商:Micrel 产品:Ethernet Switches 收发器数量:2 数据速率:10 Mb/s, 100 Mb/s 电源电压-最大:1.25 V, 3.45 V 电源电压-最小:1.15 V, 3.15 V 最大工作温度:+ 85 C 封装 / 箱体:QFN-64 封装:Tray |
| KSZ8051MNLITR | 制造商:Micrel 功能描述:Ethernet TXRX PHY 10 T100 3.3V 32 QFN |
发布紧急采购，3分钟左右您将得到回复。