- 您现在的位置：买卖IC网 > PDF目录10153 > KSZ8721CL TR (Micrel Inc)TXRX 10/100 3.3V 48-LQFP PDF资料下载
参数资料
| 型号： | KSZ8721CL TR |
| 厂商： | Micrel Inc |
| 文件页数： | 4/32页 |
| 文件大小： | 0K |
| 描述： | TXRX 10/100 3.3V 48-LQFP |
| 标准包装： | 1,000 |
| 类型： | 收发器 |
| 驱动器/接收器数： | 1/1 |
| 规程： | MII |
| 电源电压： | 3 V ~ 3.6 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 48-LQFP |
| 供应商设备封装： | 48-LQFP（7x7） |
| 包装： | 带卷 (TR) |
| 其它名称： | KSZ8721CLTR KSZ8721CLTR-ND |
第1页第2页第3页当前第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
KS8721CL
Micrel
M9999-100804
12
October 2004
auto-negotiation is enabled. It can also be configured to advertise 100BASE-TX or 10BASE-T in either full- or half-duplex mode
(please refer to “Auto-Negotiation”). Auto-negotiation is disabled in the FX mode.
During auto-negotiation, the contents of Register 4, coded in fast link pulse (FLP), are sent to its link partner under the conditions
of power-on, link-loss, or restart. At the same time, the KS8721CL monitors incoming data to determine its mode of operation.
The parallel detection circuit is enabled as soon as either 10BASE-T normal link pulse (NLP) or 100BASE-TX idle is detected.
The operation mode is configured based on the following priority:
Priority 1: 100BASE-TX, full-duplex
Priority 2: 100BASE-TX, half-duplex
Priority 3: 10BASE-T, full-duplex
Priority 4: 10BASE-T, half-duplex
When the KS8721CL receives a burst of FLP from its link partner with three identical link code words (ignoring acknowledge
bit), it will store these code words in Register 5 and wait for the next three identical code words. Once the KS8721CL detects
the second code words, it then configures itself according to the above-mentioned priority. In addition, the KS8721CL also
checks for 100BASE-TX idle or 10BASE-T NLP symbols. If either is detected, the KS8721CL automatically configures to match
the detected operating speed.
MII Management Interface
The KS8721CL supports the IEEE 802.3 MII Management Interface, also known as the Management Data Input/Output
(MDIO) Interface. This interface allows upper-layer devices to monitor and control the state of the KS8721CL. The MDIO
interface consists of the following:
A physical connection including a data line (MDIO), a clock line (MDC), and an optional interrupt line (INTRPT).
A specific protocol that runs across the above-mentioned physical connection that allows one controller to
communicate with multiple KS8721CL devices. Each KS8721CL is assigned an MII address between 0 and 31 by
the PHYAD inputs.
An internal addressable set of fourteen 16-bit MDIO registers. Registers [0:6] are required and their functions are
specified by the IEEE 802.3 specifications. Additional registers are provided for expanded functionality.
The INTPRT pin functions as a management data interrupt in the MII. An active Low or High in this pin indicates a status change
on the KS8721CL based on 1fh.9 level control. Register bits at 1bh[15:8] are the interrupt enable bits. Register bits at 1bh[7:0]
are the interrupt condition bits. This interrupt is cleared by reading Register 1bh.
MII Data Interface
The data interface consists of separate channels for transmitting data from a 10/100 802.3 compliant Media Access Controller
(MAC) to the KS8721CL, and for receiving data from the line. Normal data transmission is implemented in 4B nibble mode (4-
bit wide nibbles).
Transmit Clock (TXC): The transmit clock is normally generated by the KS8721CL from an external 25MHz reference source
at the X1 input. The transmit data and control signals must always be synchronized to the TXC by the MAC. The KS8721CL
normally samples these signals on the rising edge of the TXC.
Receive Clock (RXC): For 100BASE-TX links, the receive clock is continuously recovered from the line. If the link goes down,
and auto-negotiation is disabled, the receive clock operates off the master input clock (X1 or TXC). For 10BASE-T links, the
receive clock is recovered from the line while carrier is active, and operates from the master input clock when the line is idle.
The KS8721CL synchronizes the receive data and control signals on the falling edge of RXC in order to stabilize the signals
at the rising edge of the clock with 10ns setup and hold times.
Transmit Enable: The MAC must assert TXEN at the same time as the first nibble of the preamble, and de-assert TXEN after
the last bit of the packet.
Receive Data Valid: The KS8721CL asserts RXDV when it receives a valid packet. Line operating speed and MII mode will
determine timing changes in the following way:
For 100BASE-TX links with the MII in 4B mode, RXDV is asserted from the first nibble of the preamble to the last
nibble of the data packet.
For 10BASE-T links, the entire preamble is truncated. RXDV is asserted with the first nibble of the SFD “5D” and
remains asserted until the end of the packet.
Error Signals: Whenever the KS8721CL receives an error symbol from the network, it asserts RXER and drives “1110” (4B)
on the RXD pins. When the MAC asserts TXER, the KS8721CL will drive “H” symbols (a Transmit Error defined in the IEEE
802.3 4B/5B code group) out on the line to force signaling errors.
Carrier Sense (CRS): For 100BASE-TX links, a start-of-stream delimiter, or /J/K symbol pair causes assertion of Carrier
Sense (CRS). An end-of-stream delimiter, or /T/R symbol pair, causes de-assertion of CRS. The PMA layer will also de-assert
CRS if IDLE symbols are received without /T/R, yet in this case RXER will be asserted for one clock cycle when CRS is de-
相关PDF资料 |
PDF描述 |
|---|---|
| MS27472E18B35P | CONN RCPT 66POS WALL MNT W/PINS |
| LTC2858IDD-2#PBF | IC TXRX RS485/RS422 10-DFN |
| MS3116P8-3P | CONN PLUG 3POS STRAIGHT W/PINS |
| VE-2N4-MX-F1 | CONVERTER MOD DC/DC 48V 75W |
| MS3102R20-18PW | CONN RCPT 9POS BOX MNT W/PINS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| KSZ8721SL | 功能描述:以太网 IC 10/100 Base-TX/FX Physical Layer Transceiver, Single 3.3V Supply, 48-SSOP (Lead Free) RoHS:否 制造商:Micrel 产品:Ethernet Switches 收发器数量:2 数据速率:10 Mb/s, 100 Mb/s 电源电压-最大:1.25 V, 3.45 V 电源电压-最小:1.15 V, 3.15 V 最大工作温度:+ 85 C 封装 / 箱体:QFN-64 封装:Tray |
| KSZ8721SL TR | 功能描述:以太网 IC 10/100 Base-TX/FX Physical Layer Transceiver, Single 3.3V Supply, 48-SSOP (Lead Free) RoHS:否 制造商:Micrel 产品:Ethernet Switches 收发器数量:2 数据速率:10 Mb/s, 100 Mb/s 电源电压-最大:1.25 V, 3.45 V 电源电压-最小:1.15 V, 3.15 V 最大工作温度:+ 85 C 封装 / 箱体:QFN-64 封装:Tray |
| KSZ8721SLA4 | 功能描述:TXRX 10/100 3.3V 48-SSOP RoHS:是 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 标准包装:1,140 系列:AU 类型:收发器 驱动器/接收器数:1/1 规程:CAN 电源电压:5.3 V ~ 27 V 安装类型:表面贴装 封装/外壳:14-SOIC（0.154"，3.90mm 宽） 供应商设备封装:14-SO 包装:管件 其它名称:935267940512AU5790D14AU5790D14-ND |
| KSZ8721SLA4 TR | 功能描述:TRANSCEIVER 10/100 3.3V 48-SSOP RoHS:是 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 标准包装:1,140 系列:AU 类型:收发器 驱动器/接收器数:1/1 规程:CAN 电源电压:5.3 V ~ 27 V 安装类型:表面贴装 封装/外壳:14-SOIC（0.154"，3.90mm 宽） 供应商设备封装:14-SO 包装:管件 其它名称:935267940512AU5790D14AU5790D14-ND |
| KSZ8721SL-EVAL | 功能描述:以太网开发工具 KSZ8721SL Evaluation Board RoHS:否 制造商:Micrel 产品:Evaluation Boards 类型:Ethernet Transceivers 工具用于评估:KSZ8873RLL 接口类型:RMII 工作电源电压: |
发布紧急采购，3分钟左右您将得到回复。